Preset
Red
1.Presss MENU two times, then enter the
OPTION menu.
2.Select item with CH+ and CH-, the selected
item will highlighted red.
3.Select the language you would like to see
on your screen (English/Francais/Espanol)
with VOL+ and VOL-.
4.Press CH+ and CH- to select C.CAPTION,
the selected item highlighted with red.
When OFF displays, C.CAPTION is set off.
When displays, C.CAPTION is set active.
Press VOL+ repeatedly , the option will display
followed on the screen in turn:
C1
OPTION
Language English
Getting Started With
Personalized Setup
Getting Started With
Personalized Setup
Setting up this TV can be personalized, please refer to
this manual. It contains instructions to help you. The TV
is preset with default setting preset by manufacturer. To
get personalized setting, please read on.
1. Page 5 a brief introduction to the key functions.
2. Page 6 PICTURE.
3. Page 6 OPTION
4. Page 7 TIME
5. Page 7 PRESET
6. Page 7 V-CHIP
red.
1.Press MENU three times, then enter the CLOCK menu.
2.TIME, selected item will highlight to red;
3.Use VOL+ to adjust minute and use VOL- to adjust hour.
4.Press CH+ and CH- to change the selected parameter
as you wish; Similarly, you can set a Time On/Time
Off/Reminder/Choice;
5.You can also set a time on a channel you want, enter the
channel menu, press VOL+ or VOL- to change the
number of the channel.
Setup PRESET
1.Press the MENU four times, then enter the PRESET menu.
2.Channel: press VOL+ to change the channel you want to
preset.
3.Add/Erase: use CH+ and CH- to select the option, press
VOL+ and VOL- to add or erase TV channels to/from the
program.
4.Antenna: the default parameter is Air, which indicates
the signal receiving method is through the antenna of the
TV. Use VOL+ to change it to CATV
(IRC)/CATV(HIR)/
CATV(DDD) if you are using cable service.
5.AUTO SEARCH: press the VOL+ or VOL-, it will
automatically search for TV channels. (When
available signal is detected, the channel locked in will
release the lock, press VOL+, and the search resumes).
Setup V-CHIP
Pressing Rating on your remote controller will bring
V-CHIP to set up display on TV. Yo u will see the
following on your TV screen.
This function enables you to block certain TV
channels in according to the V-CHIP requirements
established by the FCC.
Follow the procedure below to set the V-CHIP:
Press the Rating button, you will see the V-CHIP
menu on your TV screen:
1. Press CH+ and CH- to go up and go down the menu.
2. Press VOL+ and VOL- to enter password and then
go into TV Rating and Movie Rating menu.
3. Press VOL+/- to set the and
When TV Rating is selected, press VOL+, then you
will find you need enter password, after entering the
default password 0000, you will see the following
rating table on your TV screen.
BLOCK ON BLOCK OFF.
When MPAA Rating is selected, press VOL, then you
will find you need enter password, after entering the
default password 0000, you will see the following
rating table on your TV screen.
CLOCK
V-CHIP
BLOCK OFF
TV RATING
MPAA RATING
CHANGE PASSWORD
V-CHIP
BLOCK OFF
TV RATING
MPAA RAT ING
CHANGE PASSWORD
CH key
key
VOL
1.To turn on the set press the ON/OFF button or
press the on/off key on the remote controller.
Turning The TV On
Note: When block is selected, you will see V-CHIP
function is activated .
When block is selected, you will
see V-CHIP function is not be activated .
ON
OFF
You can press
MENU button
to exchange B and U under TV Rating and MPAA
Rating.
Note: When block is selected, you will see V-CHIP
function is activated .
When block is selected, you will see
V-CHIP function is not be activated .
ON
OFF
You can press
MENU button
to exchange B and U under TV Rating and MPAA
Rating.
PICTURE parameters:
Press M(MENU) key and select PICTURE.
Press CH- and CH+ to select an item (menu will
roll and show those hidden items with the action
of the CH+ and CH-).
When a certain item is selected, it will be
highlighted red, use VOL+ and VOL- to change
the parameter to your preference.