Konica Minolta BIZHUB 500 Setting-Up Manual

Page 1 of 25

AD_NDS_SMB userauthentication set-up_ver_1_10.doc

Setting-up Guide for

bizhub C250/C351/C450/420/500/600/750

User Authentication

In combination with

Active Directory environment

NDS environment

SMB /NTLM environment

Page 2 of 25

AD_NDS_SMB userauthentication set-up_ver_1_10.doc

Page 3 of 25

AD_NDS_SMB userauthentication set-up_ver_1_10.doc

KONICA MINOLTA BIZHUB C250 / C351 / C450 / 750 / 600 – SETTING-UP OF USER

AUTHENTICATION ON ACTIVE DIRECTORY........................................................................................... 4

P

REPARATION

...................................................................................................................................................... 4

C

HECK

TCP/IP

SETTINGS

..................................................................................................................................... 4

C

ONFIGURE

U

SER AUTHENTICATION

(A

CTIVE

D

IRECTORY

) ................................................................................ 7

KONICA MINOLTA BIZHUB C250 / C351 / C450 / 750 / 600– SETTING-UP OF USER

AUTHENTICATION ON NOVELL NDS........................................................................................................ 12

C

ONFIGURE

U

SER AUTHENTICATION

(NDS) ...................................................................................................... 12

KONICA MINOLTA BIZHUB C250 / C351 / C450 / 750 / 600– SETTING-UP SMB/NTLM USER

AUTHENTICATION ......................................................................................................................................... 17

C

ONFIGURE

U

SER AUTHENTICATION

(SMB/NTLM) ......................................................................................... 17

APPENDIX .......................................................................................................................................................... 22

W

HERE TO FIND REQUIRED

I

NFORMATION

......................................................................................................... 22

T

HINKS WHICH MAKES YOUR LIFE EASIER

.......................................................................................................... 23

U

PDATES IN THIS

D

OCUMENT RELEASE

.............................................................................................................. 25

Page 4 of 25

AD_NDS_SMB userauthentication set-up_ver_1_10.doc

Konica Minolta bizhub C250 / C351 / C450 / 750 / 600 – Setting-up of User authentication on

Active Directory

This chapter described the setting-up procedure for User Authentication function in combination with a

MS Windows server supporting Active Directory. It’s mandatory that the C450 is connected to a

TCP/IP network and the correct TCP/IP settings are applied to it.

Preparation

Before setting up user authentication, please collect following information. If you have difficulties to

find the required information, please refer to the appendix “Where to find required Information:

MFP’s Administrator password

MFP’s IP address

Subnet Mask

Default gateway (optional)

Priority DNS Server address

Substitute 1 DNS Server address (optional)

Substitute 2 DNS Server address (optional)

MFP’s DNS Host Name

MFP’s DNS Domain Name

Default Domain Name

Valid user account and Password for function

check

Check TCP/IP settings

a) Press the Utility key on the Operation panel

Page 5 of 25

AD_NDS_SMB userauthentication set-up_ver_1_10.doc

b) Select “Administrator Setting”

c) Enter the Administrator Password and touch the “OK”-button.

d) Select “Network Setting”

Page 6 of 25

AD_NDS_SMB userauthentication set-up_ver_1_10.doc

e) Select “TCP/IP Settings”

f) Ensure that the right TCP/IP configuration is applied and select the Forward button (FWD. )

g) Ensure that at least the Priority DNS Server IP address is set. If no DNS server address is

set, “User Authentication” and “LDAP search with GSS-SPNEGO authentication” will not

work. Select the Forward button (FWD. )

Page 7 of 25

AD_NDS_SMB userauthentication set-up_ver_1_10.doc

h) Enter the DNS Default Domain Name and select the Forward button (FWD. ).

i) Enter the DNS Host Name and press “OK”

Configure User authentication (Active Directory)

a) Enter the Administrator Mode and select “User Authentication / Account Track”

Page 8 of 25

AD_NDS_SMB userauthentication set-up_ver_1_10.doc

b) Select “General Settings”

c) Select User Authentication “ON (External Server)”

d) Choose “Active Directory”

Page 9 of 25

AD_NDS_SMB userauthentication set-up_ver_1_10.doc

e) Select the field (button) “01” and touch “Registration” in order to register the domain name of

the domain against the user authentication shall take place.( up to 20 domain different domain

names can be registered).

f) Enter the Domain Name and press “OK”

g) Leave the registration screen by touching “OK”

Page 10 of 25

AD_NDS_SMB userauthentication set-up_ver_1_10.doc

h) Leave the External Server Authentication screen by touching “OK”

i) Leave the general settings screen by touching “OK”

j) In order to activate “User Authentication” this message has to be confirmed by touching the

[Yes] button. Please be aware that this will clear all previous programmed accounting and

Authentication data.

Page 11 of 25

AD_NDS_SMB userauthentication set-up_ver_1_10.doc

k) Try to login with a valid user account name and password. If you face any difficulties to login,

please re-check all settings and refer to the appendix – known issues.

Page 12 of 25

AD_NDS_SMB userauthentication set-up_ver_1_10.doc

Konica Minolta bizhub C250 / C351 / C450 / 750 / 600– Setting-up of User authentication on

Novell NDS

This chapter described the setting-up procedure for User Authentication function in combination with a

Novell Netware Server Ver. 5 and later.

Preparation

Before setting up user authentication, please collect following information. If you have difficulties to

find the required information, please refer to the appendix “Where to find required Information:

MFP’s Administrator password

Default NDS Tree Name

Default NDS Context Name

Valid user account name and Password for

function check (admin credential will not work,

due to Netware security setting)

Configure User authentication (NDS)

a) Press the “Utility” key on the Operation panel

Page 13 of 25

AD_NDS_SMB userauthentication set-up_ver_1_10.doc

b) Select “Administrator Setting”

c) Enter the Administrator Password and touch the “OK”-button.

d) select “User Authentication / Account Track”

Page 14 of 25

AD_NDS_SMB userauthentication set-up_ver_1_10.doc

e) Select “General Settings”

f) Select User Authentication ”ON (External Server)”

g) Choose “NDS”

Page 15 of 25

AD_NDS_SMB userauthentication set-up_ver_1_10.doc

h) Select “Default NDS Tree Name”

i) Input the default NDS tree name and touch the “OK” button

j) Select “Default NDS context name”

Page 16 of 25

AD_NDS_SMB userauthentication set-up_ver_1_10.doc

k) Input the default NDS context name and touch the “OK” button

l) Leave the administrator mode and switch off and on the main device

l) Try to login with a valid user account and password. If you face any difficulties to login, please

re-check all settings and refer to the appendix – known issues.

Page 17 of 25

AD_NDS_SMB userauthentication set-up_ver_1_10.doc

Konica Minolta bizhub C250 / C351 / C450 / 750 / 600– Setting-up SMB/NTLM User

authentication

This chapter described the setting-up procedure for User Authentication function in combination with a

Windows PC or a Computer running Samba service.

Preparation

Before setting up user authentication, please collect following information. If you have difficulties to

find the required information, please refer to the appendix “Where to find required Information:

MFP’s Administrator password

Default Domain Name

Valid user account and Password for function

check (admin credential will not work, due to

Netware security setting)

Configure User authentication (SMB/NTLM)

b) Please ensure a basic TCP/IP configuration of the MFP. IP-address and subnet mask must be

programmed. All other TCP/IP settings are optional.

c) Press the Utility key on the Operation panel

Page 18 of 25

AD_NDS_SMB userauthentication set-up_ver_1_10.doc

e) Select “Administrator Setting”

f) Enter the Administrator Password and touch the “OK”-button.

g) select “User Authentication / Account Track”

Page 19 of 25

AD_NDS_SMB userauthentication set-up_ver_1_10.doc

h) Select “General Settings”

i) Select User Authentication “ON (External Server)”

j) Choose [NTLM v1] for user authentication against a SAMBA server, or [NTML v2] for user

authentication against a Windows Server.

OR

Page 20 of 25

AD_NDS_SMB userauthentication set-up_ver_1_10.doc

k) Select “Default Domain Name”

l) Input the default Domain Name by using capital characters and touch the “OK” button

m) Leave the administrator mode and switch off and on the main device

Page is loading ...

Konica Minolta BIZHUB 500 Setting-Up Manual

This manual is also suitable for

Konica Minolta BIZHUB 500 Setting-Up Manual

Related papers

Other documents