Compaq Evo D510 e-pc Upgrade Manual

Brand: Compaq

Model: Evo D510 e-pc

Type: Upgrade Manual

Thank you for purchasing this Factory Service

Manual CD/DVD from servicemanuals4u.com.

Please check out our eBay auctions for more great

deals on Factory Service Manuals:

servicemanuals4u

Upgrade Guide

Evo D510 e-pc

Document Part Number: 305513-001

August 2002

305513-001.bookPageiTuesday,August20,20024:35PM

Compaq and the Compaq logo are trademarks of Compaq Information

Technologies Group, L.P. in the U.S. and/or other countries.

Intel, Pentium, Intel Inside, and Celeron are trademarks of Intel Corporation in

the U.S. and/or other countries.

All other product names mentioned herein may be trademarks of their respective

companies.

Compaq Computer Corporation shall not be liable for technical or editorial

errors or omissions contained herein or for incidental or consequential damages

in connection with the furnishing, performance, or use of this material. The

information in this document is provided “as is” without warranty of any kind,

including, but not limited to, the implied warranties of merchantability and

fitness for a particular purpose, and is subject to change without notice. The

warranties for Compaq products are set forth in the express limited warranty

statements accompanying such products. Nothing herein should be construed as

constituting an additional warranty.

This document contains proprietary information that is protected by copyright.

No part of this document may be photocopied, reproduced, or translated to

another language without the prior written consent of Compaq Computer

Corporation.

WARNING:

Text set off in this manner indicates that failure to follow

directions could result in bodily harm or loss of life.

CAUTION: Text set off in this manner indicates that failure to follow

directions could result in damage to equipment or loss of information.

Upgrade Guide

Evo D510 e-pc

First Edition August 2002

Document Part Number: 305513-001

305513-001.bookPageiiTuesday,August20,20024:35PM

Upgrade Guide iii

Contents

For Your Safety and Comfort

Upgrading and Replacing Hardware

General Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Opening the e-pc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Internal Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Upgrading or Replacing Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Replacing the Hard Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Replacing the Optical Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Configuring an IDE Device After Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Removing or Replacing the System Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Replacing the Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Replacing the Power Supply Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Replacing the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

305513-001.bookPageiiiTuesday,August20,20024:35PM

Upgrade Guide 1

For Your Safety and Comfort

WARNING: Misuse of your personal computer or failure to establish a

safe and comfortable work environment may result in discomfort or serious

injury. Refer to the

Safety & Comfort Guide,

included in the documentation

provided with your computer and available on the Web site at

http://www.compaq.com/comfortguide

, for more information on

choosing a workspace and creating a safe and comfortable work

environment.

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. For more

information, refer to Safety & Regulatory Information, also included in the

documentation provided with your computer.

305513-001.bookPage1Tuesday,August20,20024:35PM

Upgrade Guide 3

Upgrading and Replacing Hardware

This guide describes how to upgrade or replace hardware

components, such as memory, hard drive, optical drive, processor,

system board, battery, and power supply.

If you want to find out about accessories available for your e-pc, refer

to the following Web site:

http://www.compaq.com/products/desktops/options/index.html

General Precautions

Before upgrading or replacing components, be sure to carefully read

all of the applicable instructions, cautions, and warnings in this guide.

WARNING:

To reduce the risk of personal injury from electrical shock

and/or hot surfaces, be sure to disconnect the power cord from the wall

outlet, and allow the internal system components to cool before touching.

CAUTION:

Static electricity can damage the electronic components of

the personal computer or optional equipment. Before beginning these

procedures, ensure that you are discharged of static electricity by briefly

touching a grounded metal object.

Opening the e-pc

1. Exit all software applications, shut down the operating system

software, turn off the personal computer and any external devices,

then disconnect the power cord from the power outlet.

2. Unlock the e-pc and remove the port control system (if fitted).

305513-001.bookPage3Tuesday,August20,20024:35PM

4 Upgrade Guide

Upgrading and Replacing Hardware

3. Disconnect all cables from the computer.

4. Push the two green latches inward.

5. Slide out the chassis from the enclosure.

305513-001.bookPage4Tuesday,August20,20024:35PM

Upgrade Guide 5

Upgrading and Replacing Hardware

Internal Components

Hard Drive

You can replace hard drive with a

larger one

One Front-Access Device Shelf

CD-ROM drive, CD-RW drive or DVD drive

Main Memory Modules:

(266MHz DDR SDRAM)

2 sockets for 128 MB, 256 MB, 512

MB or 1GB modules up to 2 GB

maximum

Switch block

One Front-Access Device Shelf

CD-ROM drive, CD-RW drive or DVD drive

305513-001.bookPage5Tuesday,August20,20024:35PM

6 Upgrade Guide

Upgrading and Replacing Hardware

Upgrading or Replacing Memory

✎

Use only memory modules provided for your e-pc model. The use of

other memory modules is not supported. For information about

supported accessories, connect to

http://www.compaq.com.

32 MB

and 64 MB modules are not supported. Install 128 MB, 256 MB,

512 MB or 1 GB non-ECC DDR SDRAM modules.

1. Open the e-pc as shown in “Opening the e-pc” on page 3.

2. Lift up the hard drive retaining bracket.

3. Slide out the drive tray to gain access to the memory modules.

memory modules

305513-001.bookPage6Tuesday,August20,20024:35PM

Upgrade Guide 7

Upgrading and Replacing Hardware

4. There are two memory sockets. Align the notches on the bottom

of the module with the corresponding marks on the socket and

push it firmly into place. The clips close automatically.

5. Replace the chassis in the enclosure.

Replacing the Hard Drive

WARNING: For your safety, disconnect the power cord and all external

cables.

1. Open the e-pc as shown in “Opening the e-pc” on page 3.

2. Lift up the hard drive retaining bracket.

305513-001.bookPage7Tuesday,August20,20024:35PM

8 Upgrade Guide

Upgrading and Replacing Hardware

3. Detach the data and power cables from the hard drive.

✎

To prevent damage to the data and power cables, pull on the tab or

connector instead of the cable itself.

To prevent damage to the hard drive, handle it with care and do not

drop it.

4. Lift the drive tray clear of the e-pc.

305513-001.bookPage8Tuesday,August20,20024:35PM

Upgrade Guide 9

Upgrading and Replacing Hardware

5. Remove the four screws securing the old hard drive to the tray

and pull the drive out of the tray.

6. Insert a new drive in the tray and install the four drive-retaining

screws.

7. Insert the drive tray in the e-pc (the drive will only fit into the

tray one way).

8. Reattach the data and power cables.

9. Replace the chassis in the enclosure.

10. Verify the new configuration by checking the Summary screen.

To access the Summary Screen, press

immediately after

startup, then press

Esc.

✎

To reinstall the operating system and drivers on the newly-installed

hard drive, use the Restore Plus! CD and operating system CD

provided with the e-pc. In addition, you can find the most up-to-date

versions of drivers on the support site at

http://www.compaq.com/support.

screws

scre

305513-001.bookPage9Tuesday,August20,20024:35PM

10 Upgrade Guide

Upgrading and Replacing Hardware

Replacing the Optical Drive

WARNING: Do not operate controls, make adjustments, or perform

procedures to a laser device other than those specified in the operators

manual or in the laser device installation guide.

Allow only Compaq authorized service technicians to repair the laser

equipment.

1. Open the e-pc as shown in “Opening the e-pc” on page 3.

2. Pull on the plastic latch below the optical drive to release it.

305513-001.bookPage10Tuesday,August20,20024:35PM

Upgrade Guide 11

Upgrading and Replacing Hardware

3. Slide the optical drive tray out the front of the chassis and detach

the cable at the back of the drive.

4. Release the catch holding the old drive in place and remove the

old drive from the tray.

5. Place the new drive in the tray and secure with the sliding catch.

6. Attach the cable to the new drive and slide the drive tray back into

the e-pc until it clicks into place.

7. Replace the chassis in the enclosure.

8. Verify the new configuration by checking the Summary screen.

Restart the computer. When the Compaq logo is displayed,

press

F8,

then press

Esc.

305513-001.bookPage11Tuesday,August20,20024:35PM

12 Upgrade Guide

Upgrading and Replacing Hardware

Configuring an IDE Device After Installation

After installing any device, you can check via the Summary Screen

that your e-pc has correctly identified the new configuration. To view

the Summary screen, restart the computer. When the Compaq logo is

displayed, press

F8,

then select Summary from the list of options.

If the configuration is not correct, run the Setup program to configure

the device. To enter the Setup program, To access Computer Setup,

restart the computer. When the Compaq logo is displayed, press

F8,

then select Setup from the list of options.

IDE drives are automatically detected by the Setup program.

However, a newly installed device may require that you install an

appropriate device driver. Refer to your operating system

documentation for details. You can obtain the latest drivers from the

support Web site at

http://www.compaq.com/support.

The IDE cables in your e-pc are cable select. You must, therefore, set

the jumpers on any IDE devices you install to cable select. See the

documentation for the device for more information.

305513-001.bookPage12Tuesday,August20,20024:35PM

Upgrade Guide 13

Upgrading and Replacing Hardware

Removing or Replacing the System Board

1. Open the e-pc as shown in “Opening the e-pc” on page 3.

2. Remove all cables from the old system board.

3. Turn the chassis over and remove the six screws that secure the

system board to the chassis.

305513-001.bookPage13Tuesday,August20,20024:35PM

14 Upgrade Guide

Upgrading and Replacing Hardware

4. Remove the old system board from the chassis.

a. Lift up the board at the front side of the chassis.

b. Carefully disengage the rear connectors and lift the board out

of the chassis.

5. If you are replacing the system board, remove the memory

modules, heatsink, and processor from the old system board and

install them on the new system board. (Refer to “Upgrading or

Replacing Memory” on page 6 and “Replacing the Processor” on

page 15 for instructions.)

6. Insert the system board. Line up the rear connectors carefully,

then reconnect the four cables. Lower the front end of the board

into position and fasten the screws to secure the board.

7. Replace the chassis in the enclosure.

305513-001.bookPage14Tuesday,August20,20024:35PM

Upgrade Guide 15

Upgrading and Replacing Hardware

Replacing the Processor

1. Open the e-pc as shown in “Opening the e-pc” on page 3.

2. Remove the system board as shown in “Removing or Replacing

the System Board” on page 13.

3. Locate the processor (it is covered by a heatsink).

4. Unscrew the screws that secure the heatsink to the system board

and remove the heatsink.

CAUTION: If the processor is stuck to the heatsink, twist the heatsink

to break the seal. Never attempt to pry the heatsink from the processor

as doing so may pull the processor from its socket and irreparably

damage it.

processor (covered by heatsink)

screws

305513-001.bookPage15Tuesday,August20,20024:35PM

16 Upgrade Guide

Upgrading and Replacing Hardware

5. Lift the processor socket lever and remove the old processor.

Carefully insert the new processor, then lower the lever back into

place while pressing lightly down on the processor to ensure that

it seats properly.

CAUTION: Insert the processor carefully, making sure that the orientation

is correct. It can go in one way only; do not apply excessive force.

6. Remove all old thermal interface material from the underside of

the heatsink by using the alcohol wipe that is provided with the

processor kit.

7. Squeeze the contents of the thermal grease syringe onto the top of

the processor.

8. Place the heatsink on top of the processor.

305513-001.bookPage16Tuesday,August20,20024:35PM

Upgrade Guide 17

Upgrading and Replacing Hardware

9. Secure the heatsink using the springs and screws. Attach the

screws in the order shown, first with just a few turns and then,

once all four are in place, screwing them in fully.

10. Replace the system board in the chassis.

11. Replace the chassis in the enclosure.

12. Ensure that the latest version of BIOS is installed on your e-pc.

To learn which version of BIOS is currently installed on your

e-pc, restart the e-pc. When the Compaq logo is displayed, press

F8,

then select Summary from the list of options. To get the

latest BIOS version for your e-pc, connect to the support Web site

http://www.compaq.com/support.

305513-001.bookPage17Tuesday,August20,20024:35PM

Page is loading ...

Compaq Evo D510 e-pc Upgrade Manual

Compaq Evo D510 e-pc Upgrade Manual

Compaq Evo D510 e-pc Upgrade Manual

Related papers

Other documents