ROHS EmCORE-i2702 User manual

EmCORE-i2702

3.5” Miniboard

User’s Manual

Version 1.0

2010.10

This page is intentionally left blank.

- i -

Index

Contents

Chapter 1 - Introduction ............................................ 1

1.1 Copyright Notice .........................................................2

1.2 About this User’s Manual ...........................................2

1.3 Warning .......................................................................2

1.4 Replacing the Lithium Battery ...................................3

1.5 Technical Support .......................................................3

1.6 Warranty ......................................................................4

1.7 Packing List.................................................................5

1.8 Ordering Information ..................................................5

1.9 Specications .............................................................6

1.10 Board Dimensions ....................................................7

1.11 Installing the Memory ...............................................8

Chapter 2 - Installation ..............................................9

2.1 Block Diagram...........................................................10

2.2 Jumpers and Connectors ........................................11

Jumpers ............................................................................12

CMOS Jumper Settings (JBAT1)...........................12

CF Card Select (J2) ................................................13

LCD Power (JVLCD1) .............................................14

COM2 RS-232/422/485 Slect (JRS2) .....................15

Connectors .......................................................................16

External SMB Connector (JSMB1) .......................16

FRONT PANEL (JFRT1) .........................................17

Serial ATA (SATA1/SATA2) .....................................18

RS-422/485 Serial Port (JCOM2) ...........................19

RS-232/422/485 Serial Port (COM2) ......................20

SATA Power Connector (J8) ..................................21

3DUDOOHO3RUWConnector (LPT).............................22

LED for Ethernet (CN2) ..........................................23

LAN Connector (LAN2) ..........................................24

Audio Connector (AUDIO1) ...................................25

USB Connector (USB2) .........................................26

- ii -

PWR-ATX Connector (PWR1/2) .............................27

ATX Feature Connector (PWR3) ...........................28

AT Power Switch (JPWR1) ....................................29

TV Connector (TV1) ...............................................30

INVERTOR Connector (INV1) ................................31

LVDS LCD Connector (LVDS1) ..............................32

Digital I/O (DIO1) ....................................................33

FAN Connector (SYSF1) ........................................34

2.3 The Installation Paths of CD Driver.........................35

Chapter 3 - BIOS ......................................................36

3.1 BIOS Introduction .....................................................37

3.2 BIOS Setup ................................................................38

3.3 Standard CMOS Features ........................................39

3.4 Advance BIOS Features ...........................................42

3.5 Advanced Chipset Features ....................................44

3.6 Integrated Peripherals ..............................................46

3.7 Power Management Setup .......................................50

3.8 PNP/PCI Congurations ...........................................52

3.9 PC Health Status .......................................................53

3.10 Load Optimized Defaults .......................................54

3.11 Set Password .........................................................55

3.12 Save & Exit Setup ...................................................56

3.13 Exit Without Saving ................................................57

3.14 Award BIOS POST Codes ......................................58

Chapter 4 - Appendix .........................................62

4.1 I/O Port Address Map ...............................................63

4.2 Interrupt Request Lines (IRQ) ..................................64

4.3 BIOS memory mapping ............................................65

4.4 Watchdog Timer (WDT) Setting ...............................65

4.5 Digital I/O Setting ......................................................66

Index

- 1 -

Introduction

1Chapter 1

Introduction

- 2 -

Introduction

The information in this document is subject to change without prior notice in

order to improve the reliability, design and function. It does not represent a

commitment on the part of the manufacturer.

Under no circumstances will the manufacturer be liable for any direct, indirect,

special, incidental, or consequential damages arising from the use or inability

to use the product or documentation, even if advised of the possibility of such

damages.

This document contains proprietary information protected by copyright.

All rights are reserved. No part of this manual may be reproduced by any

mechanical, electronic, or other means in any form without prior written

permission of the manufacturer.

1.2 About this User’s Manual

This User’s Manual is intended for experienced users and integrators with

hardware knowledge of personal computers. If you are not sure about any

description in this User’s Manual, please consult your vendor before further

handling.

1.3 Warning

Single Board Computers and their components contain very delicate

Integrated Circuits (IC). To protect the Single Board Computer and its

components against damage from static electricity, you should always follow

the following precautions when handling it :

Disconnect your Single Board Computer from the power source when you

want to work on the inside.

Hold the board by the edges and try not to touch the IC chips, leads or

circuitry.

Use a grounded wrist strap when handling computer components.

Place components on a grounded antistatic pad or on the bag that came

with the Single Board Computer, whenever components are separated

from the system.

1.

2.

3.

4.

1.1 Copyright Notice

- 3 -

Introduction

1.4 Replacing the Lithium Battery

Incorrect replacement of the lithium battery may lead to a risk of explosion.

The lithium battery must be replaced with an identical battery or a battery type

recommended by the manufacturer.

Do not throw lithium batteries into the trash-can. It must be disposed of in

accordance with local regulations concerning special waste.

1.5 Technical Support

If you have any technical difculties, please do not hesitate to call or e-mail

our customer service.

http://www.arbor.com.tw

E-mail:info@arbor.com.tw

- 4 -

Introduction

1.6 Warranty

This product is warranted to be in good working order for a period of two years

from the date of purchase. Should this product fail to be in good working order

at any time during this period, we will, at our option, replace or repair it at no

additional charge except as set forth in the following terms. This warranty

does not apply to products damaged by misuse, modications, accident or

disaster.

Vendor assumes no liability for any damages, lost prots, lost savings or any

other incidental or consequential damage resulting from the use, misuse of,

or inability to use this product. Vendor will not be liable for any claim made by

any other related party.

Vendors disclaim all other warranties, either expressed or implied, including

but not limited to implied warranties of merchantibility and tness for a

particular purpose, with respect to the hardware, the accompanying product’s

manual(s) and written materials, and any accompanying hardware. This

limited warranty gives you specic legal rights.

Return authorization must be obtained from the vendor before returned

merchandise will be accepted. Authorization can be obtained by calling or

faxing the vendor and requesting a Return Merchandise Authorization (RMA)

number. Returned goods should always be accompanied by a clear problem

description.

- 5 -

Introduction

1.7 Packing List

1.8 Ordering Information

Before you begin installing your single board, please make sure that the following

materials have been shipped:

1 x EmCORE-i2702 3.5” Miniboard with heat sink

1 x Driver CD

1 x Quick Installation Guide

If any of the above items is damaged or missing, contact your vendor immediately.

EmCORE-i2702

Intel Atom™ N270 1.6GHz 3.5” Miniboard

CBK-8-3945-00

Cable Kit

1 x USB Cable

1 x KB & MS Cable

1 x Audio Cable

1 x SATA Cable

1 x COM Cable

1 x Print Cable

1 x LAN Cable

1 x IDE Cable

- 6 -

Introduction

1.9 Specications

Form Factor 3.5” Miniboard

CPU Intel®

Atom™ N270 CPU 1.6GHz with 533MHz FSB

Chipset Intel® 9

45GSE + Intel® ICH7M

System Memory 1 x 200-pin DDR2

533MHz SO-DIMM Socket Up to 1GB

VGA/ LCD

Controller

Integrated Intel Graphics Media

Accelerator 950, support

QXGA up to 2048 x 1546, LVDS support 18/36-bit, support

dual dispaly, TV-out

Ethernet 2 x Realtek 8111C PCIe Gigabit Ethernet controllers

I/O Chips ITE 8718F

BIOS

Phoenix-A

ward BIOS version 6.0PG, support 4MB SPI

Flash ROM

Audio

Realtek

ALC655 AC97 Audio CODEC, MIC-in/ Line-In/ Line-

Out

Serial Port

2 x COM ports

(COM1: RS-2

32, COM2: RS-232/422/485 selectable)

Digital I/O 4

-in / 4-out

Storage

2 x Serial

ATA 150MB/s HDD transfer rate

1 x ATA-66, support 2 ATAPI devices

1 x Floppy connector share with LPT port

Parallel Port 1 x LPT Port (SPP/EPP/ECP mode selectable)

KB/MS Support Standard PS/2 Keyboard and Mouse

Universal Serial Bus 4

x USB 2.0 ports

Expansion Interface Mini PCI

Watchdog Timer 1~2

55 levels (sec or min)

Hardware Monitor

Chip

Integrated in ITE8718F

RTC Support Real Time Clock

Power Connector DC +12V

Operation Temp. 0

o

C ~ 60

o

C

Dimension (L x W) 1

46 x 102 mm (5.7 ” x 4.0 ”)

- 7 -

Introduction

1.10 Board Dimensions

- 8 -

Introduction

1.11 Installing the Memory

To install the Memory module, locate the Memory SO-DIMM slot on the board

and perform as below:

Adjust the socket polarizing key and the board key to the same direction.

Insert the board obliquely. Moreover, lay the board in parallel to the opening

at angle of 20

o

to 30

o

, and softly insert the board so as to hit the socket

bottom. Stopping insertion halfway will result in improper insertion.

Applying the board side notch in parallel to the socket bottom so that the

board position cannot be displaced, press the board side notch up, and x

it to the latch portion at both socket edges. Press the board side notch, and

release the notch with a snap “click” tone, if the printed board exceeds the

latch claw head.

1.

2.

3.

Side notch

Key

Latch knob

Latch claw

Latch section

Latch arm

Polarizing key

1

2

3

Procedures for board extraction

Apply the thumb nail to the latch knob at both socket edges. Forcibly widen

the latch knobs to right and left ways, and release the latch. Then draw the

board out along an angle where the board is raised.

- 9 -

Installation

2Chapter 2

Installation

Chapter 2 - Installation

- 10 -

Installation

2.1 Block Diagram

TV-Out

Mobile

Intel®

945GSE

Intel®

Atom

N270

FSB

533MHz

400/533MHz

1 x 200-pin SO-DIMM

up to 1GB

Intel®

ICH7-M

AC Link

Single Channel DDR2

Analog

R.G.B.

Super IO

ITE 8718F

DMI

Serial ATA I/F

IDE ATA-66

2 x SATA

VGA

1 x IDE

PCIe*1 I/F

1 x Connector

1 x pin-header

COM ports

COM1,2

LPT1

LPT

KB/ MS

KB, MS

8-bit

Programmable

DIO

LPC

PCI Bus

Mini-PCI

Socket

AUDIO

2 x Realtek

8111C GbE

ALC655

AC97

CODEC

USB ports x 4

USB x 4

LVDS1

Dual-Channel 18/36-bit

- 11 -

Installation

2.2 Jumpers and Connectors

- 12 -

Installation

Jumpers

CMOS Jumper Settings (JBAT1)

Type: onboard 3-pin 2.0mm header

Pin Mode

1-2 Keep CMOS

2-3 Clear CMOS

Default setting: Keep CMOS

INV1LED2

LVDS2

JVLCD4

INV2

SATA2

USB1

LAN1

KBM1

RN1

VGA1

COM1

Mini PCI

SYF1

- 13 -

Installation

CF Card Select (J2)

Type: onboard 2.0mm 3-pin headers.

Pin Mode

1 N/A

2-

3 ON Master

2-

3 OFF Slave

INV1LED2

LVDS2

JVLCD4

INV2

SATA2

USB1

LAN1

KBM1

RN1

VGA1

COM1

Mini PCI

SYF1

- 14 -

Installation

LCD Power (JVLCD1)

Type: onboard 3-pin 2.54mm header

Power

JVLCD1

5

V

1-2 ON

3

.3V

2-3 ON

Default setting: 3.3V

INV1LED2

LVDS2

JVLCD4

INV2

SATA2

USB1

LAN1

KBM1

RN1

VGA1

COM1

Mini PCI

SYF1

- 15 -

Installation

COM2 RS-232/422/485 Slect (JRS2)

Type: onboard 2.0mm 2x3-pin header

JRS2 Select 1-2 3-4 5-6

RS-232 ON OFF OFF

RS-422 OFF ON OFF

RS-

485 OFF OFF ON

Default setting: RS-232

INV1LED2

LVDS2

JVLCD4

INV2

SATA2

USB1

LAN1

KBM1

RN1

VGA1

COM1

Mini PCI

SYF1

- 16 -

Installation

External SMB Connector (JSMB1)

Type: onboard 2.0mm 3-pin header

Pin Description

1 SMB_DATA_MAIN

2 SMB_CLK_MAIN

3 ETX_SMI#

Connectors

INV1LED2

LVDS2

JVLCD4

INV2

SATA2

USB1

LAN1

KBM1

RN1

VGA1

COM1

Mini PCI

SYF1

Page is loading ...

ROHS EmCORE-i2702 User manual

ROHS EmCORE-i2702 User manual

Related papers

Other documents