ROHS ITX-i7418VL User manual

ITX-i7418VL

Mini ITX Industrial Motherboard

User’s Manual

Version 1.0

2007.05

Table of Contents

Chapter 1 Introduction ...........................................................4

1.1 Copyright Notice ..........................................................................5

1.2 About this User’s Manual ...........................................................5

1.3 Warning ......................................................................................5

1.4 Replacing the lithium battery .......................................................6

1.5 Technical Support .......................................................................6

1.6 Warranty .....................................................................................7

1.7 Packing List ................................................................................8

1.8 Ordering Information ...................................................................8

1.9 Speciﬁcation ...............................................................................9

1.10 Board Dimensions ..................................................................10

1.11 Installing the CPU ...................................................................12

1.12 Installing the Memory .............................................................13

Chapter 2 Installation .............................................................14

2.1 Jumpers and Connectors .........................................................15

2.2 ATX: ATX Power Supply Connector .........................................16

2.3 JVLCD1: LCD Panel Voltage Selection ...................................16

2.4 LVDS1: LVDS LCD Connector .................................................17

2.5 CPUF1: CPU Fan Power Connector ........................................17

2.6 SYSF1: System Fan Power Connector ....................................18

2.7 IDE2: Secondly 44-pin IDE Connector .....................................18

2.8 IDE1: Primary 40-pin IDE Connector .......................................19

2.9 JFRT1: Switches and Indicators ..............................................19

2.10 MPCI1: MiniPCI slot ...............................................................19

2.11 PCI1: Standard 32 bit/33MHz PCI slot ..................................19

2.12 JBAT1: CMOS Setup ..............................................................20

2.13 FDD1: FDD Connector ...........................................................20

2.14 IR1: Infrared Connector ..........................................................20

2.15 INV1: LCD Inverter Connector ................................................21

2.16 DIO1: Digital I/O Connector ....................................................21

2.17 COM1: Two D-SUB 9 Connector .............................................22

2.18 USB5: USB Connector ............................................................22

2.19 CN2: 10/100 RJ-45 + USB1 + USB2 .......................................22

2.20 AUDIO1: Audio Interface Port ................................................23

2.21 USB3/ USB4 ...........................................................................23

2.22 LPT1: Parallel Port Connector ...............................................23

2.23 VGA1: CRT Connector ...........................................................24

2.24 KBM1: PS/2 Keyboard & Mouse ............................................24

Index

2

Index

3

Chapter 3 BIOS ......................................................................26

3.1 BIOS Introduction .....................................................................27

3.2 BIOS Setup ..............................................................................27

3.3 Standard CMOS Features ........................................................28

3.4 Advanced BIOS Features ........................................................31

3.5 Advanced Chipset Features .....................................................35

3.6 Integrated Peripherals ..............................................................39

3.7 Power Management Setup .......................................................44

3.8 PNP/PCI Conﬁgurations ...........................................................47

3.9 PC Health Status ......................................................................49

3.10 Frequency/Voltage Control .....................................................50

3.11 Load Optimized Defaults ........................................................51

3.12 Set Password .........................................................................52

3.13 Save & Exit Setup ..................................................................53

3.14 Exit Without Saving ................................................................54

3.15 BIOS Beep Sound code list ....................................................55

3.16 BIOS memory mapping ..........................................................55

3.17 Award BIOS Post Codes .......................................................56

Chapter 4 Appendix ...............................................................60

4.1 I/O Port Address Map ...............................................................61

4.2 Interrupt Request Lines (IRQ) ..................................................62

1Chapter 1

Introduction

4

1.1 Copyright Notice

The information in this document is subject to change without prior notice in

order to improve the reliability, design and function. It does not represent a

commitment on the part of the manufacturer.

Under no circumstances will the manufacturer be liable for any direct, indi-

rect, special, incidental, or consequential damages arising from the use or in-

ability to use the product or documentation, even if advised of the possibility

of such damages.

This document contains proprietary information protected by copyright. All

rights are reserved. No part of this manual may be reproduced by any me-

chanical, electronic, or other means in any form without prior written permis-

sion of the manufacturer.

1.2 About this User’s Manual

This User’s Manual is intended for experienced users and integrators with

hardware knowledge of personal computers. If you are not sure about any

description in this User’s Manual, please consult your vendor before further

handling.

1.3 Warning

Single Board Computers and their components contain very delicate

Integrated Circuits (IC). To protect the Single Board Computer and its

components against damage from static electricity, you should always follow

the following precautions when handling it :

1. Disconnect your Single Board Computer from the power source when you

want to work on the inside

2. Hold the board by the edges and try not to touch the IC chips, leads or

circuitry

3. Use a grounded wrist strap when handling computer components.

4. Place components on a grounded antistatic pad or on the bag that came

with the Single Board Computer, whenever components are separated

from the system

Introduction

5

1.4 Replacing the lithium battery

Incorrect replacement of the lithium battery may lead to a risk of explosion.

The lithium battery must be replaced with an identical battery or a battery

type recommended by the manufacturer.

Do not throw lithium batteries into the trashcan. It must be disposed of in

accordance with local requlations concerning special waste.

1.5 Technical Support

If you have any technical difﬁculites, please consult the user’s manual ﬁrst

at:

ftp://ftp.arbor.com.tw/pub/manual

Please do not hesitate to call or e-mail our customer service when you still

can not ﬁnd out the answer.

http://www.arbor.com.tw

E-mail:info@arbor.com.tw

Introduction

6

1.6 Warranty

This product is warranted to be in good working order for a period of two

years from the date of purchase. Should this product fail to be in good

working order at any time during this period, we will, at our option, replace

or repair it at no additional charge except as set forth in the following terms.

This warranty does not apply to products damaged by misuse, modiﬁcations,

accident or disaster.

Vendor assumes no liability for any damages, lost proﬁts, lost savings or any

other incidental or consequential damage resulting from the use, misuse of,

or inability to use this product. Vendor will not be liable for any claim made

by any other related party.

Vendors disclaim all other warranties, either expressed or implied, including

but not limited to implied warranties of merchantibility and ﬁtness for a par-

ticular purpose, with respect to the hardware, the accompanying product’s

manual(s) and written materials, and any accompanying hardware. This

limited warranty gives you speciﬁc legal rights.

Return authorization must be obtained from the vendor before returned

merchandise will be accepted. Authorization can be obtained by calling or

faxing the vendor and requesting a Return Merchandise Authorization (RMA)

number. Returned goods should always be accompanied by a clear problem

description.

Introduction

7

1.7 Packing List

If any of the above items is damaged or missing, contact your vendor

immediately.

1.8 Ordering Information

ITX-i7418VL w/o

CF

Mini-ITX Pentium M Socket 478 Industrial Motherboard

with CRT/LCD, Audio and LAN

ITX-i7418VL Mini-ITX Pentium M Socket 478 Industrial Motherboard

with CRT/LCD, Audio, CF socket (Optional) and LAN

ITX-i7418VL/

CM600 (optional)

Mini-ITX Celeron M 600MHz Industrial Motherboard

with CRT/LCD, Audio, CF socket and LAN

ITX-i7418VL/

CM1000

(optional)

Mini-ITX Celeron M 1.0GHz Industrial Motherboard

with CRT/LCD, Audio, CF socket and LAN

Cable Kit CBK-05-7418-00

1x ITX-i7418VL Mini ITX Industrial MB

1x I/O Bracket

or

1x CPU Heat Sink or Cooler

1x CD-ROM (For Driver used)

1x Quick Installation Guide

1x Warranty Card

Introduction

8

1.9 Speciﬁcation

Product Name ITX-i7418VL

Form Factor Mini ITX Industrial MB (170 x 170 mm)

Processor μFC-PGA478 pin Pentium-M Up to 1.8GHz

FSB 400MHz

μFC-BGA479 pin Celeron-M 600MHz or 1GHz

FSB 400MHz (Optional)

Chipset Intel 852GM + Intel ICH4

System Memory 2 x 184-pin DDR 200/266 DIMM Up to 2GB

SDRAM

VGA/LCD Controller UMA 852GM AGP Video Controller w/ CRT and

LVDS support (dual mode independent display)

Ethernet Intel 82562EZ PHY 10/100Mbps Fast Ethernet

I/O Chips WINBOND W83627HG

BIOS Phoenix-Award BIOS 6.0PG, 4MB Flash ROM

Audio AC’97 Codec, MIC-in/Line-in/Line-out

IDE Interface 1 x ATA-100 and 1 x ATA-33 (4 ATAPI devices)

1 x CompactFlash II up to 4GB

Serial Port 2 x COM port (COM 1, COM 2: RS-232)

Parallel Port SPP/EPP/ECP mode

KBMS Standard PS/2 KBMS

Universal Serial Bus 6 x USB 2.0 (4 ports Stack connectors & 2 ports

by pin header.)

DIO 16 bit programmable Digital I/O

LCD 18/36 bit LVDS

Expansion Interface 1 x MiniPCI & 1 x PCI Slot

Hardware Monitor

Chip

Integrated in W83627HG

RTC Real Time Clock

Power Input Connector ATX Power Connector

Operation Temp.

0ºC ~ 60ºC

Watchdog Timer

127-level Reset

Dimension (L x W)

170 x 170 mm (6.7” x 6.7”)

Introduction

9

1.10 Board Dimensions

Introduction

10

Introduction

11

1.11 Installing the CPU

Introduction

12

The processor socket comes with a screw to secure the CPU. As showing in

the picture as below, loose the screw ﬁrst before inserting the CPU.

Place the CPU into the socket by making sure the notch on the corner of

the CPU corresponding with the notch on the inside of the socket. Once the

CPU has slide into the socket, lock the screw.

Make sure that heat sink of the CPU top surface is in complete contact to

avoid the CPU overheating problem.

If not, it would cause your system or CPU to be hanged, unstable, damaged.

Loose

Lock

1.12 Installing the Memory

Introduction

13

To install the Memory module, locate the Memory DIMM slot on the board

and perform as below:

1. Hold the Memory module so that the key of the Memory module align

with those on the Memory DIMM slot.

2. Gently push the Memory module in an upright position and a right way

until the clips of the DIMM slot close to lock the Memory module in place,

when the Memory module touches the bottom of the DIMM slot.

3. To remove the Memory module, just pressing the clips of DIMM slot with

both hands.

Lock Lock

2Chapter 2

Installation

14

2.1 Jumpers and Connectors

Installation

15

2.2 ATX: ATX Power Supply Connector

Pin Description Pin Description

11

3.3V 1 3.3V

12 -12V 2 3.3V

13 GND 3 GND

14 PS-ON 4 5V

15 GND 5 GND

16 GND 6 5V

17 GND 7 GND

18 -5V 8 PW-OK

19 5V 9 5VSB

20 5V 10 +12V

1

1020

11

2.3 JVLCD1: LCD Panel Voltage Selection

The voltage of LCD panel could be selected by JVLCD1 in 5V or 3.3V.

Pin Voltage

1-2 5V

2-3 3.3V (Default)

1 3

Installation

16

2.4 LVDS1: LVDS LCD Connector

The LVDS connector on board DF-13 30-pin header and supports 18-bit or

36-bit.

Pin Description Pin Description

2 VDD 1 VDD

4 TX2CLK+ 3 TX1CLK+

6 TX2CLK- 5 TX1CLK-

8 GND 7 GND

10 TX2D0+ 9 TX1D0+

12 TX2D0- 11 TX1D0-

14 GND 13 GND

16 TX2D1+ 15 TX1D1+

18 TX2D1- 17 TX1D1-

20 GND 19 GND

22 TX2D2+ 21 TX1D2+

24 TX2D2- 23 TX1D2-

26 GND 25 GND

28 TX2D3+ 27 TX1D3+

30 TX2D3- 29 TX1D3-

2.5 CPUF1: CPU Fan Power Connector

CPUF1 is a 3-pin header for the CPU fan. The fan must be a 12V fan.

Pin Description

1 GND

2 +12V

3 FAN_CTL

Installation

17

12

30 29

13

2.6 SYSF1: System Fan Power Connector

SYSF1 is a 3-pin header for the CPU fan. The fan must be a 12V fan.

Pin Description

1 GND

2 +12V

3 FAN_CTL

2.7 IDE2: Secondly 44-pin IDE Connector

Pin Description Pin Description

1 IDE RESET 2 GND

3 DATA7 4 DATA8

5 DATA6 6 DATA9

7 DATA5 8 DATA10

9 DATA4 10 DATA11

11 DATA3

12 DATA12

13 DATA2 14 DATA13

15 DATA1 16 DATA14

17 DATA0 18 DATA15

19 GND 20 N/C

21 REQ 22 GND

23 IO RWITE 24 GND

25 IO READ 26 GND

27 IO READY 28 IDESEL

29 DACK 30 GND

31 IRQ14 32 N/C

33 ADDR1 34 ATA66 DETECT

35 ADDR0 36 ADDR2

37 CS#2 38 CS#3

39 IDEACTP 40 GND

41 VCC(+5V) 42 VCC(+5V)

43 GND 44 N/C

1 2

4443

13

Installation

18

2.8 IDE1: Primary 40-pin IDE Connector

2.10 MPCI1: MiniPCI slot

2.11 PCI1: Standard 32 bit/33MHz PCI slot

2.9 JFRT1: Switches and Indicators

It provides connectors for system indicators that provides light indication

of the computer activities and switches to change the computer status.

Pin Description Pin Description

1 Power LED+ 2 PWRBTN+

3 GND 4 PWRBTN-

5 GND 6 RESET+

7 HDD LED+ 8 RESET-

9 HDD LED- 10 SPEAKER+

11

SMBCLK 12 SPEAKER+

13 SMBDATA 14 SPEAKER-

15 GND 16 SPEAKER-

2

16

1

15

1

240

39

Installation

19

Page is loading ...

ROHS ITX-i7418VL User manual

ROHS ITX-i7418VL User manual

Related papers

Other documents