AmazonBasics B07XFSSFDS is a 2-Ton Capacity Hydraulic Trolley Jack designed to lift (but not support) loads consisting of one end of a vehicle. It features a sturdy construction, a low profile design, and a convenient carrying handle for easy portability. With a maximum lifting height of 13.4 inches, this jack is suitable for most cars and light trucks. It also comes equipped with a release valve for controlled lowering of the load. For safety, it is recommended to use a pair of adequately rated jack stands to support the vehicle after lifting.
AmazonBasics B07XFSSFDS is a 2-Ton Capacity Hydraulic Trolley Jack designed to lift (but not support) loads consisting of one end of a vehicle. It features a sturdy construction, a low profile design, and a convenient carrying handle for easy portability. With a maximum lifting height of 13.4 inches, this jack is suitable for most cars and light trucks. It also comes equipped with a release valve for controlled lowering of the load. For safety, it is recommended to use a pair of adequately rated jack stands to support the vehicle after lifting.
Hydraulic Trolley Jack, 2-Ton Capacity
Cric Rouleur Hydraulique, Capacité de 2Tonnes
Hydraulischer Hebelroller, 2Tonnen Kapazität
Cric Idraulico a Carrello, Capacità 2Tonnellate
Gato Hidráulico de Botella, Capacidad 2Toneladas
Hydraulische Autokrik, Capaciteit 2 Ton
油 圧トローリージャッキ、容 量 2トン
B07XFSSFDS
English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Français . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Deutsch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Italiano . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Español . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Nederlands . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
日本語 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
3
EN
IMPORTANT SAFEGUARDS
Read these instructions carefully and retain them for future use.
If this product is passed to a third party, then these instructions
must be included.
When using the product, basic safety precautions should always be
followed to reduce the risk of injury including the following:
DANGER
Risk of death! Never work
on, around, or under a load supported only
by the product. Use a pair of adequately
rated jack stands.
DANGER
Risk of death! Support the vehicle with appropriate
means, immediately after lifting.
DANGER
Risk of death! Lift only on areas of the vehicle as
specified by the vehicle manufacturer.
CAUTION
Risk of injury! Wear appropriate personal protective
equipment (PPE) as required by applicable to local regulations.
• The owner and/or operator shall have an understanding of the
product, its operating characteristics, and safety operating
instructions before operating the product. Safety information shall
be understood. If the operator is not fluent in English, the product
and safety instructions shall be discussed with the operator in the
operator’s native language by the purchaser, owner, or owner’s
designee, making sure that the operator comprehends their contents.
• Study, understand, and follow all instructions before operating this
product.
• Visual inspection shall be made before each use of the product by
checking for abnormal conditions, such as cracked welds, leaks, and
damaged, loose, or missing parts.
• Other inspections shall be made per product operating instructions.
• The product shall be inspected immediately if the product is believed to
have been subject to an abnormal load or shock. This inspection should
be made by a manufacturer’s or supplier’s authorized repair facility.
• Owners and operators should be aware that repair of this equipment
may require specialized knowledge and facilities.
• Any product that appears to be damaged in any way, is found to
be worn, or operates abnormally SHALL BE REMOVED FROM
SERVICE UNTIL REPAIRED. Necessary repairs should be made by
manufacturer’s or supplier’s authorized repair facility.
4
EN
• The product shall be maintained by a qualified person.
• Do not exceed rated capacity.
• Use only on a hard, level surface.
• Ensure load is secured to the product.
• No alterations shall be made to this product.
• Only attachments and/or adapters supplied by or approved by the
manufacturer shall be used.
• Release load-locking devices (if employed) slowly and carefully.
• Center load on saddle (lift pad) prior to lifting.
• Do not move or dolly the vehicle while it is on the jack.
• Before using the product with the vehicle, always engage the vehicle
parking brakes and block the wheels.
SAVE THESE INSTRUCTIONS
Intended Use
• This product is designed to lift (not support), rated capacity loads
consisting of one end of a vehicle. Immediately after lifting, the load
must be supported by a pair of appropriately rated jack stands. Wood
blocks, bricks, or concrete blocks are not acceptable substitutes for
jack stands.
• This product is intended for private use only. It is not intended for
commercial use in garages or repair shops.
• This product is intended to be used in dry indoor and outdoor areas.
• No liability will be accepted for damages resulting from improper use
or non-compliance with these instructions.
5
EN
Do not:
• Use on three wheel cars, trailers, mobile homes (caravans), RVs and
campers.
• Use on curved or tubular vehicles.
• Use in extreme climates, freezer application or in strong magnetic
fields.
• Use in potentially explosive atmospheres or in mines.
• Use for lifiting of persons.
• Handle loads which could lead to dangerous situations (e.g molten
metal, acids, radiating materials, especially brittle loads).
Product Description
A
B
C E
G
I
D
F
H
A Actuating handle (base) F Lift arm (lifting beam)
B Actuating handle receptacle G Saddle (lift pad)
C Cover plate H Actuating handle (extension)
D Oil plug I Release valve
E Carrying handle
6
EN
Before First Use
• Check the product for transport damages.
• Remove all the packing materials.
• Perform air purging procedure as described in the “Purging Air from
Hydraulic System” section.
DANGER
Risk of suffocation! Keep any packaging materials
away from children – these materials are a potential source of danger,
e.g. suffocation.
Assembly
Step 1:
H
A
Step 2:
C
B
7
EN
Step 3:
E
Purging Air from Hydraulic System
NOTICE
Air bubbles may become trapped occasionally inside
the hydraulic system, reducing its efficiency. Purge the air following the
directions below.
NOTICE
Oil can leak from the release valve (I) whilst purging air.
Have a rag ready in case of any leakages.
• Without any weight on the jack, open the release valve (I) by making
one full turn in a counter-clockwise direction.
• Remove the cover plate (C) to expose the oil plug (D).
• Pump the handle rapidly with 8 full strokes to push the air through the
system.
• Use a flat screwdriver and slightly push the oil plug (D) to the side to
purge trapped air.
• Securely close the release valve (I) in a clockwise direction.
• Refit the cover plate (C).
• Check for proper pump and lift action. Repeat the above steps until
the air is fully purged.
8
EN
Inspection
• Visual inspection shall be made before each use of the product by
checking for abnormal conditions, such as cracked welds, leaks, and
damaged, loose, or missing parts.
• The product shall be inspected immediately if the product is believed
to have been subject to an abnormal load or shock. This inspection
should be made by a manufacturer’s or supplier’s authorized repair
facility.
• Inspect the work area as well. Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
Operation
Lifting up the vehicle
DANGER
Risk of death! Never work
on, around, or under a load supported only
by the product. Use a pair of adequately
rated jack stands.
• Engage the vehicle brake and block the wheels for better lift stability.
• Place the product at a 90º angle to the vehicle under the vehicle’s lift
point. Position the product so the saddle (lift pad) (G) is centered and
will contact the lift point firmly.
• Consult the vehicle’s owner manual if you are in doubt about the
location of the lift points.
• Ensure the product is at a 90º angle to the vehicle and under the
specified points for lifting.
• Close the release valve (I) by rotating it in a clockwise direction.
• Pump the handle until the saddle (lift pad) (G) is in close proximity to
the lift point.
• Continue pumping until the vehicle is lifted to the desired height.
• Remove the actuating handle (A and H) from the handle
receptacle (B).
• After lifting, support the load with appropriately rated jack stands
(notprovided).
9
EN
NOTICE
Operator must keep eyes on the product and load at all
times during operation.
NOTICE
If several jacks are used together, raise the vehicle on both
sides with the same speed. Keep the same height on both sides.
NOTICE
Always ensure that the load is stabilized or supported in
such a way that it will not shift during lifting or lowering procedure.
NOTICE
Never wire, clamp or otherwise disable the release valve (I)
function. Use the handle (A) to ensure proper release valve (I) operation.
Lowering the vehicle
DANGER
Risk of death! Ensure there are no objects or persons
under the vehicle before lowering the vehicle.
• Pump the handle to raise the vehicle from the jack stand(s).
• Remove the jack stand(s).
• Use the handle (A) to slowly turn the release valve (I) in a
counter-clockwise direction to lower the vehicle onto the ground.
WARNING
Risk of death or injury! Use extreme caution when
lowering the jack. Opening the release valve (I) too fast can cause the
jack to lower rapidly.
WARNING
Risk of death or injury! If the product should
malfunction at any time, secure the load with jack stands and refer to the
Troubleshooting section.
Specifications
Maximum loading capacity: approx. 4409 lbs (2000 kg)
Lifting height:
min. 5.31" (135 mm)
max. 13.4" (340 mm)
Net weight: approx. 19.2 lbs (8.7 kg)
Dimensions (W x H x D):
approx. 17.6 x 7.72 x 5.3"
(447 x 196 x 135 mm)
Product life time: 2 years
10
EN
Troubleshooting
Causes and
solutions
The product
does not lift
load
The product
does not hold
load
The product
does not
lower
Completely close the
release valve (I).
X X
Weight capacity
exceeded.
X
Purge air from
system.
X
Add oil. X X
Drain excessive oil.
Lubricate moving
parts.
X
Jack is binding or
foreign obstruction.
X
Causes and
solutions
Poor jack lifting
The product does not
lift to full extension
Completely close the
release valve (I).
X
Weight capacity
exceeded.
Purge air from
system.
X
Add oil. X X
Drain excessive oil.
Lubricate moving
parts.
Jack is binding or
foreign obstruction.
X
11
EN
Cleaning and Maintenance
Cleaning
• To clean the product, wipe with a soft, slightly moist cloth.
• Never use corrosive detergents, wire brushes, abrasive scourers,
metal or sharp utensils to clean the product.
Adding oil
• Place the product in an upright position.
• Turn the release valve (I) in a counter-clockwise direction to allow the
saddle (G) to fully retract. Use force if necessary.
• Remove the cover plate (C) and then the oil plug (D).
• Fill the Hydraulic Jack Oil up to the lower rim of the fill hole. Keep dirt
and other material clear when pouring. Do not overfill.
• Refit the oil plug (D) and then the cover plate (C).
Changing/draining oil
CAUTION
Take special care when handling hydraulic oil. Eye &
skin irritant. If contact with eyes occurs, flush thoroughly with water for
15minutes while lifting eyelids and get prompt medical attention.
NOTICE
For best performance replace the hydraulic oil at least once
per year.
• Place the product in an upright position.
• Turn the release valve (I) in a counter-clockwise direction to allow the
saddle (G) to fully retract. Use force if necessary.
• Remove the cover plate (C) and then the oil plug (D).
• Turn the product upside down and drain the fluid into a certified oil
container.
• Refit the oil plug (D) and then the cover plate (C).
Lubricating
NOTICE
Risk of malfunction! Never lubricate or grease the rods of
the pump and lifting cylinder.
• For light duty use, regularly lubricate for all external moving parts
once a month.
• For heavy duty and frequent use, lubricate once a week.
• Use only SAE10 grade, special-purpose hydraulic oil (not provided).
Dispose of all used and spilled oil.
12
EN
Other maintenance
• Regularly check and maintain the oil level.
• Check the ram every 3 months for any rust or corrosion. Clean as
needed and wipe with an oil cloth.
• Keep the rating label clean and readable at all time. Stop using the
product if label is not readable or if it is detached.
• Necessary repairs or modification should be made by manufacturer’s
or supplier’s authorized repair facility.
Oil disposal
• Dispose of hydraulic oil, residue and the empty container in
accordance with all local, state and federal laws and regulations. It
is illegal to dump waste oil into landfill or waterways. Disposing of
used hydraulic oil the incorrect manner has the potential to pollute the
environment.
Storage
• Always store the product in the fully lowered position.
• If the product is stored outdoors, lubricate all parts before and after
use to ensure the product stays in good working condition.
• For long term storage drain the hydraulic oil.
Feedback and Help
Love it? Hate it? Let us know with a customer review.
AmazonBasics is committed to delivering customer-driven products
that live up to your high standards. We encourage you to write a review
sharing your experiences with the product.
US: amazon.com/review/review‑your‑purchases#
UK: amazon.co.uk/review/review‑your‑purchases#
US: amazon.com/gp/help/customer/contact‑us
UK: amazon.co.uk/gp/help/customer/contact‑us
13
EN
Exploded View
41
40 39
38
37
36
35
34
33
32
31
30
29
28
42
2
31617181718
19
18
17
20
21
22
15
27 92623
24 25
14 13 12 11 10
8
7
6
1
4
5
14
EN
No. Part Description Quantity
1
QLQD2A.1-1 Handle cover 1
2 T820033.1(asm) Actuating handle 1
3 T820050-1 Cover plate 1
4 Locating pin 1
5 Positioning spring 1
6 Supporting shaft 1
7 Pin for frame 1
8 Supporting shaft 1
9 Connecting rod 2
10 Lift arm assembly 1
11 GB894.1-16 C-clip Ø16 mm 2
12 GB91-2X20 Cotter pin Ø2 x 20 mm 1
13 T82000Y.3-1 Saddle 1
14 QLQD2C.5-2a Saddle pin 1
15 GB894.1-10 C-clip Ø10 mm 4
16 Right frame assembly 1
17 Spring washer M12 6
18 GB6170-M12 Nut M12 6
19 Carrying handle 1
20 GB97.1-12 Washer M12 2
21 T820013-7 Sleeve for front wheel 2
22 T820013D-2 Front wheel 2
23 Saddle base assembly 1
24 Pin for saddle base 1
25 GB894.1-13 C-clip Ø13 mm 1
26 Shaft for front wheel 1
15
EN
No. Part Description Quantity
27
Pin for lift arm 1
28 T820033XE.2(asm) Rear caster assembly 2
29 Left frame assembly 1
30 Return spring 1
31 TF1201C-29 Oil plug 1
32
T820050.1 Power unit assembly 1
33 GB308-6 Steel ball bearing Ø6 mm 1
34 T83003.2-10(asm) Release value assembly 1
35 QLQD2A.2-5(asm) Pump plunger assembly 1
36 QLQD2A.2-7b U-Bracket for plunger 1
37 T820050.1-2 Handle receptacle 1
38 QLQD2B-3
Roundwire snap ring
Ø1.4 x 26 mm
1
39 QLQD2A.2-19 Pin for pump plunger 1
40 QLQD2A.2-20 Pin for unit base 1
41 QLQD2B.2-5
Roundwire snap ring
Ø1.2 x 20 mm
1
42 T820050.MF Seal kit 1
amazon.com/AmazonBasics
V01-12/19
MADE IN CHINA
FABRIQUÉ EN CHINE
HERGESTELLT IN CHINA
PRODOTTO IN CINA
HECHO EN CHINA
GEMAAKT IN CHINA
中国製
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
AmazonBasics B07XFSSFDS is a 2-Ton Capacity Hydraulic Trolley Jack designed to lift (but not support) loads consisting of one end of a vehicle. It features a sturdy construction, a low profile design, and a convenient carrying handle for easy portability. With a maximum lifting height of 13.4 inches, this jack is suitable for most cars and light trucks. It also comes equipped with a release valve for controlled lowering of the load. For safety, it is recommended to use a pair of adequately rated jack stands to support the vehicle after lifting.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
AmazonBasics B07XFTCQY3 User manual
-
AmazonBasics B083T54H2S User manual
-
AmazonBasics B07TVBYDV2 User manual
-
AmazonBasics HF-50006-BY User manual
-
AmazonBasics B071DZHLXH User manual
-
AmazonBasics WI143654BW User manual
-
AmazonBasics B07W48YG15 User manual
-
AmazonBasics B07W48JPQX User manual
-
AmazonBasics B07WMRJ68R User manual
-
AmazonBasics WK3003-2 User manual
Other documents
-
BigRed T80501 Operating instructions
-
Autojack TJ300 Owner's manual
-
Ronix RH-4903 User manual
-
-
-
BigRed T84025 User manual
-
-
BigRed T93007 User manual
-
Strongway 3-Ton Long Ram Hydraulic Jack Owner's manual
-
Strongway 8-Ton Long Ram Air/Hydraulic Jack Owner's manual
