Welded Bottle Jack
Cric Bouteille Soudé
Geschweißter Flaschenheber
Cric a Bottiglia Saldata
Gato Hidráulico de Botella Soldado
Gelaste Potkrik
溶 接ボトルジャッキ
B07XFSH2FL, B07XFTCQY3
8-Ton 10-Ton
English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Français . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Deutsch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Italiano . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Español . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Nederlands . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
日本語 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
3
EN
IMPORTANT SAFEGUARDS
Read these instructions carefully and retain them for future use.
If this product is passed to a third party, then these instructions
must be included.
When using the product, basic safety precautions should always be
followed to reduce the risk of injury including the following:
DANGER
Risk of death! Never work
on, around, or under a load supported only
by the product. Use a pair of adequately
rated jack stands.
DANGER
Risk of death! Support the vehicle with appropriate
means, immediately after lifting.
DANGER
Risk of death! Lift only on areas of the vehicle as
specified by the vehicle manufacturer.
CAUTION
Risk of injury! Wear appropriate personal protective
equipment (PPE) as required by applicable local regulations.
• The owner and/or operator shall have an understanding of the
product, its operating characteristics, and safety operating
instructions before operating the product. Safety information shall
be understood. If the operator is not fluent in English, the product
and safety instructions shall be discussed with the operator in the
operator’s native language by the purchaser, owner, or owner’s
designee, making sure that the operator comprehends their contents.
• Study, understand, and follow all instructions before operating this
product.
• Visual inspection shall be made before each use of the product by
checking for abnormal conditions, such as cracked welds, leaks, and
damaged, loose, or missing parts.
• Other inspections shall be made per product operating instructions.
• The product shall be inspected immediately if the product is believed
to have been subject to an abnormal load or shock. This inspection
should be made by a manufacturer’s or supplier’s authorized repair
facility.
• Owners and operators should be aware that repair of this equipment
may require specialized knowledge and facilities.
• Any product that appears to be damaged in any way, is found to
be worn, or operates abnormally SHALL BE REMOVED FROM
SERVICE UNTIL REPAIRED. Necessary repairs should be made by
manufacturer’s or supplier’s authorized repair facility.
4
EN
• The product shall be maintained by a qualified person.
• Do not exceed rated capacity.
• Use only on a hard, level surface.
• Ensure load is secured to the product.
• No alterations shall be made to this product.
• Only attachments and/or adapters supplied by or approved by the
manufacturer shall be used.
• Release load-locking devices (if employed) slowly and carefully.
• Center load on saddle (lift pad) prior to lifting.
• Before using the product with the vehicle, always engage the vehicle
parking brakes and block the wheels.
SAVE THESE INSTRUCTIONS
Intended Use
• This product is designed to lift (not support), rated capacity loads
consisting of one end of a vehicle. Immediately after lifting, the load
must be supported by a pair of appropriately rated jack stands.
Woodblocks, bricks, or concrete blocks are not acceptable
substitutes for jack stands.
• This product is intended for private use only. It is not intended for
commercial use in garages or repair shops.
• This product is intended to be used in dry indoor and outdoor areas.
• No liability will be accepted for damages resulting from improper use
or non-compliance with these instructions.
Do not:
• Use on three wheel cars or trailers (caravans).
• Use in extreme climates, freezer application or in strong magnetic
fields.
• Do not use in potentially explosive atmospheres or in mines.
• Use for lifting of persons.
• Handle loads which could lead to dangerous situations (e.g molten
metal, acids, radiating materials, especially brittle loads).
5
EN
Product Description
B D E
C
F G
A
A
Actuating handle (extension)
E
Actuating handle receptacle
B
Actuating handle (base)
F
Release valve
C
Oil plug
G
Safety valve
D
Saddle (lift pad)
Before First Use
• Check the product for transport damages.
• Remove all the packing materials.
• Place the product on its base on a flat and level surface.
• Operate the pump 6 times to evenly distribute the hydraulic oil within
the hydraulic system.
DANGER
Risk of suffocation! Keep any packaging materials
away from children – these materials are a potential source of danger,
e.g. suffocation.
6
EN
Inspection
• Visual inspection shall be made before each use of the product by
checking for abnormal conditions, such as cracked welds, leaks, and
damaged, loose, or missing parts.
• The product shall be inspected immediately if the product is believed to
have been subject to an abnormal load or shock. This inspection should
be made by a manufacturer’s or supplier’s authorized repair facility.
• Inspect the working area. Keep work area clean and well lit. Cluttered
or dark areas can cause accidents.
Assembly
BA E
Operation
Lifting the vehicle
DANGER
Risk of death! Never work
on, around, or under a load supported only
by the product. Use a pair of adequately
rated jack stands.
• Engage the vehicle brake and block the wheels for better lift stability.
• Place the product at a 90º angle to the vehicle under the vehicle’s lift
point. Position the product so the saddle (lift pad) (D) is centered and
will contact the lift point firmly.
• Consult the vehicle’s owner manual if you are in doubt about the
location of the lift points.
• Close the release valve (F) by rotating it in a clockwise direction.
•
Pump the handle until the saddle (lift pad) (D) is in close proximity to
the lift point.
7
EN
• Continue pumping until the vehicle is lifted to the desired height.
• Remove the actuating handle (A and B) from the handle receptacle (E).
• After lifting, support the load with appropriately rated jack stands
(not provided).
NOTICE
If several jacks are used together, raise the vehicle on both
sides with the same speed. Keep the same height on both sides.
NOTICE
Always ensure that the load is stabilized or supported in
such a way that it will not shift during lifting or lowering procedure.
NOTICE
Operator must keep eyes on the product and load at all
times during operation.
Lowering the vehicle
DANGER
Risk of death! Ensure there are no objects or persons
under the vehicle before lowering the vehicle.
• Pump the handle to raise the vehicle from the jack stand(s).
• Remove the jack stand(s).
• Use the handle (B) to slowly turn the release valve (F) in a
counter-clockwise direction to lower the vehicle onto the ground.
WARNING
Risk of death or injury! Use extreme caution when
lowering the jack. The handle may move rapidly. Opening the release
valve (F) too fast can cause the jack to lower rapidly.
WARNING
Risk of death or injury! If the product should
malfunction at any time, secure the load with jack stands and refer to the
Troubleshooting section.
Purging air from hydraulic system
NOTICE
Air bubbles may become trapped occasionally inside
the hydraulic system, reducing its efficiency. Purge the air following the
directions below.
NOTICE
Oil can leak from the release valve (I) whilst purging air.
Have a rag ready in case of any leakages.
• Without any weight on the jack, open the release valve (F) by making
one full turn in a counter-clockwise direction.
• Pump the handle rapidly with 8 full strokes to push the air through the
system.
• Use a flat screwdriver and slightly push the oil plug (C) to the side to
purge trapped air.
• Securely close the release valve (F) in a clockwise direction.
8
EN
• Check for proper pump and lift action. Repeat the above steps until
the air is fully purged.
Troubleshooting
Causes and
solutions
The product
does not lift
load
The product
does not hold
load
The product
does not
lower
Completely close the
release valve (F).
X X
Weight capacity
exceeded.
X
Purge air from
system.
X
Add oil. X X
Drain excessive oil.
Lubricate moving
parts.
X
Jack is binding or
foreign obstruction.
X
Causes and
solutions
Poor jack lifting
The product does not
lift to full extension
Completely close the
release valve (F).
X
Weight capacity
exceeded.
Purge air from
system.
X
Add oil. X X
Drain excessive oil.
Lubricate moving parts.
Jack is binding or
foreign obstruction.
X
9
EN
Cleaning and Maintenance
Cleaning
• To clean the product, wipe with a soft, slightly moist cloth.
• Never use corrosive detergents, wire brushes, abrasive scourers,
metal or sharp utensils to clean the product. Do not use brake or
transmission fluids or regular motor oil.
Maintenance
• Lubricate the ram, linkages, saddle (D) and pump mechanism with
light oil. Grease wheel bearings and axles.
• Regularly check and maintain the oil level.
• Check the ram every 3 months for any rust or corrosion. Clean as
needed and wipe with an oil cloth.
• Keep the rating label clean and readable at all time. Stop using the
product if label is not readable or if it is detached.
• Necessary repairs or modification should be made by manufacturer’s
or supplier’s authorized repair facility.
Adding oil
• Place the product in an upright position.
• Turn the release valve (F) in a counter-clockwise direction to allow the
saddle (D) to fully retract. Use force if necessary.
• Remove the oil plug (C).
• Fill the Hydraulic Jack Oil up to the lower rim of the fill hole. Keep dirt
and other material clear when pouring. Do not overfill.
• Refit the oil plug (C).
Changing/draining oil
CAUTION
Take special care when handling hydraulic oil. Eye &
skin irritant. If contact with eyes occurs, flush thoroughly with water for
15minutes while lifting eyelids and get prompt medical attention.
NOTICE
For best performance replace the hydraulic oil at least once
per year.
• Lower the saddle (D) and remove the oil plug (C).
•
Lay the product on its side and drain the fluid into a certified oil container.
• Fill the Hydraulic Jack Oil up to the lower rim of the oil filler hole.
Keepdirt and other material clear when pouring. Do not overfill.
• Refit the oil plug (C).
10
EN
Oil disposal
•
Dispose of hydraulic oil, residue and the empty container in accordance
with all local, state and federal laws and regulations. It is illegal to dump
waste oil into landfill or waterways. Disposing of used hydraulic oil the
incorrect manner has the potential to pollute the environment.
Storage
• Always store the product in the fully lowered position.
• If the product is stored outdoors, lubricate all parts before and after
use to ensure the product stays in good working condition.
• For long term storage drain the hydraulic oil.
Specifications
Model: B07XFSH2FL
Net weight: 10.6 lbs (4.8 kg)
Dimensions (W x H x D):
4.88 x 8.74-17.60 x 4.17"
(124 x 222-447 x 106 mm)
Maximum lift capacity: 8-Ton (8,000 kg)
Product life time (all models): 2 years
Model: B07XFTCQY3
Net weight: 10.6 lbs (4.8 kg)
Dimensions (W x H x D):
4.88 x 8.74-17.6 x 4.17"
(124 x 222-447 x 106 mm)
Maximum lift capacity: 10-Ton (10,000 kg)
Product life time (all models): 2 years
11
EN
Exploded View
1
2
3
4
5
6
7
8
9
10
11
16
15
14
13
12
17
18
19
23
22
20
21
25
24
No. Description Quantity
1 Roundwire snap ring 1
2
Rectangular ring 2
3 0-ring 1
4 Ram assembly 1
5 Bowl washer 1
6 0-Ring 1
7 Roundwire snap ring 1
8 Base welding part 1
9 Oil plug 1
10 Steel ball bearing Ø6 mm 1
11 Release valve assembly 1
12 Plastic plug 1
13 Safety valve 1
14 Spring 1
12
EN
No. Description Quantity
15 Spring holder 1
16 Steel ball bearing Ø3 mm 1
17 Steel ball bearing Ø5 mm 2
18 Bowl washer 1
19 Pump plunger assembly 1
20 Reusable cotter pin Ø1.2 18 mm 2
21 Pin 2
22 Handle socket assembly 1
23 Handle assembly 1
24 Spring 1
25 Seal kit 1
Feedback and Help
Love it? Hate it? Let us know with a customer review.
AmazonBasics is committed to delivering customer-driven products
that live up to your high standards. We encourage you to write a review
sharing your experiences with the product.
US: amazon.com/review/review‑your‑purchases#
UK: amazon.co.uk/review/review‑your‑purchases#
US: amazon.com/gp/help/customer/contact‑us
UK: amazon.co.uk/gp/help/customer/contact‑us
amazon.com/AmazonBasics
V01-02/20
MADE IN CHINA
FABRIQUÉ EN CHINE
HERGESTELLT IN CHINA
PRODOTTO IN CINA
HECHO EN CHINA
GEMAAKT IN CHINA
中国製
/
