2. Toro
  3. 40in Bagger Enhancement Kit, TURBO FORCE Cutting Unit for Mid-Size Mowers

Toro 40in Bagger Enhancement Kit, TURBO FORCE Cutting Unit for Mid-Size Mowers Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Toro 40in Bagger Enhancement Kit, TURBO FORCE Cutting Unit for Mid-Size Mowers Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Form No. 3354-112 Rev A
40in Bagger Enhancement Kit
For 2006 and After Mid-Size Mowers
Model No. 110–2025
Installation Instructions
Loose Parts
Use the chart below to verify that all parts have been shipped.
Step
Description
Qty.
Use
1
No parts required
–
Prepare the mower deck for
installation.
Right side rubber bafe
1
Left side rubber bafe
1
Left metal bafe stiffener
1
Carriage bolt (5/16 x 1 inch)
8
Locknut (5/16 inch)
8
2
Right metal bafe stiffener
1
Install the bafes.
Step
1
Preparing the Mower Deck
No Parts Required
Procedure
1. P osition the mo w er on a flat surface .
2. Diseng ag e the PTO , mo v e the motion control
lev ers to the neutral loc k ed position and set
the parking brak e .
3. Stop the engine , remo v e the k ey , and w ait for
all mo ving par ts to stop before lea ving the
operating position.
4. Lift the front of the mac hine and suppor t the
mac hine using jac k stands .
5. T horoughly clean the mo w er dec k. All debris
m ust be remo v ed to ensure the baffle will fit
properly ag ainst the mo w er dec k.
6. R e pair all bent and damag ed areas of the
mo w er dec k and re place any missing par ts .
Mechanical or h y draulic jacks may f ail to
suppor t the machine and cause a serious
injur y .
• Use jack stands when suppor ting the
machine.
• Do not use h y draulic jacks.
Step
2
Installing the Bafes
Parts needed for this step:
1
Right side rubber bafe
1
Left side rubber bafe
1
Left metal bafe stiffener
8
Carriage bolt (5/16 x 1 inch)
8
Locknut (5/16 inch)
1
Right metal bafe stiffener
Procedure
Note: Install bolts as sho wn in Figure 1 .
© 2005—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Register at www.Toro.com. Original Instructions (EN)
Printed in the USA.
All Rights Reserved
Note: T here are different ends on the left and
right metal baffle stiffeners . See Figure 1 to
identify the difference betw een the left and right
metal stiffeners .
1. Install the left side r ubber baffle and the left
metal baffle stiffener with 4 bolts (5/16 x 1
inc h) and 4 loc kn uts (5/16 inc h) ( Figure 1 ).
2. Install the right side r ubber baffle and the right
metal baffle stiffener with 4 bolts (5/16 x 1
inc h) and 4 loc kn uts (5/16 inc h) ( Figure 1 ).
3. R otate the cutting blades and mak e sure they
do not hit the baffles .
Figure 1
1. Mower deck
5. Carriage bolt (5/16 x 1
inch)
2. Locknut (5/16 inch)
6. Right side rubber bafe
3. Left side rubber bafe 7. Left metal bafe stiffener
4. Right metal bafe stiffener 8. Note the different ends on
bafes
2
/