Troy-Bilt 31AM56R3711 Fast Start Guide

Type
Fast Start Guide

This manual is also suitable for

Troy-Bilt 31AM56R3711 is a powerful tool designed to help you tackle tough snow conditions. With its reliable electric start, you can easily get it up and running, even in cold weather. The chute control allows you to direct snow where you want it, while the adjustable chute deflector helps you control the height and distance of your throws.

Troy-Bilt 31AM56R3711 is a powerful tool designed to help you tackle tough snow conditions. With its reliable electric start, you can easily get it up and running, even in cold weather. The chute control allows you to direct snow where you want it, while the adjustable chute deflector helps you control the height and distance of your throws.

Upper Handle
Shift Lever
Chute
Control Rod
778-13254A© 2016 31AM56R3
Chute
Chute Base
A
B
A. Remove cotter pin, wing nut and
hex screw from chute control head.
B. Remove clevis
pin and bow-tie
pin from chute
support bracket.
Insert the opposite end of the chute
control rod into the coupler below the
handle panel.
Insert the cotter pin removed in Step 2
into the center hole to secure the round
end of the rod to the chute control head.
Secure the chute control head
to the support bracket with the
remaining hardware removed
in Step 2.
Place chute onto chute
base with the chute
control rod positioned
beneath the handle panel.
Reinstall the hex bolt
removed in Step 2 but
do not secure with wing
nut at this time.
Insert the round end of the chute control
rod (hole pointing upward) as far
as possible into the chute control head.
B
C
A. Loosen the top two lock nuts securing the upper
and lower handle and remove the two carriage
screws from the lower handle and set aside .
B. Place shift lever into
F6 position.
C. Pivot upper handle
into operating
position.
D. Attach the two
carriage screws and
lock nuts removed
in Step 1. Finish
securing the handle
by tightening the
top two lock nuts loosened
in Step 1.
D
A
Chute Control
Head
Chute Support
Bracket
1
4
2
5
3
6
READ AND UNDERSTAND ALL INSTRUCTION, WARNING, AND DANGER LABELS.
PARA INSTRUCCIONES EN ESPOL, REFIÉRASE AL MANUAL DEL OPERADOR.
IMPORTANT: READ OPERATOR'S MANUAL AND ENGINE MANUAL THOROUGHLY
AND FOLLOW THE IMPORTANT SAFE OPERATION PRACTICES BEFORE OPERATING .
Need Help? Call 1-888-TO-HELP-U
778-13254A© 2016 31AM56R3
Oil Fill /
Dipstick
Electric Starter
Button
Electric Starter
Outlet
Primer
Key
Throttle
Control
Choke
Control
Gas Fill
Move throttle control into
the Fast position.
Move the choke control
into the Choke
position.
A. Connect an extension cord
to the electric starter outlet.
B. Plug the other end of the
cord into a three-prong
120-volt, grounded, AC
receptacle.
Push primer
three times.
Insert the key into the
key switch until the key
snaps into place.
Do not turn the key!
A. To start engine,
push the starter
button.
B. When engine
starts, slowly move
choke knob into
the Run position.
C. Disconnect cord
from power
receptacle first and
then from snow
thrower’s outlet.
Fill fuel tank with clean,
fresh gasoline. Do not fill
above the base of fuel
tank neck.
Check the oil level using
the dipstick. Add oil if
necessary. (Refer to the
Operator’s Manual)
7
10
8
11
9
12
READ AND UNDERSTAND ALL INSTRUCTION, WARNING, AND DANGER LABELS.
PARA INSTRUCCIONES EN ESPOL, REFIÉRASE AL MANUAL DEL OPERADOR.
IMPORTANT: READ OPERATOR'S MANUAL AND ENGINE MANUAL THOROUGHLY
AND FOLLOW THE IMPORTANT SAFE OPERATION PRACTICES BEFORE OPERATING .
Need Help? Call 1-888-TO-HELP-U
  • Page 1 1
  • Page 2 2

Troy-Bilt 31AM56R3711 Fast Start Guide

Type
Fast Start Guide
This manual is also suitable for

Troy-Bilt 31AM56R3711 is a powerful tool designed to help you tackle tough snow conditions. With its reliable electric start, you can easily get it up and running, even in cold weather. The chute control allows you to direct snow where you want it, while the adjustable chute deflector helps you control the height and distance of your throws.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI