MoTrade C-HR Installation guide

Type
Installation guide

MoTrade C-HR is an innovative interface that transforms your Toyota C-HR's infotainment system into a versatile hub for smartphone connectivity and multimedia enjoyment. With CarPlay and Android Auto compatibility, you can seamlessly integrate your mobile device, accessing navigation, music, messaging, and a wide range of apps directly from your car's display. The interface also supports Bluetooth connectivity, allowing you to make hands-free calls and stream audio wirelessly. Installation is straightforward, and the included detailed instructions guide you through the process step by step.

MoTrade C-HR is an innovative interface that transforms your Toyota C-HR's infotainment system into a versatile hub for smartphone connectivity and multimedia enjoyment. With CarPlay and Android Auto compatibility, you can seamlessly integrate your mobile device, accessing navigation, music, messaging, and a wide range of apps directly from your car's display. The interface also supports Bluetooth connectivity, allowing you to make hands-free calls and stream audio wirelessly. Installation is straightforward, and the included detailed instructions guide you through the process step by step.

Motrade December 2023 ©
Installation instruction for Carplay Android Auto interface
Toyota C-HR 2016-2019
The interface is connected via three connection plugs on the radio.
It is estimated that it takes about 30-45 minutes of work to connect the interface. No
programming is necessary.
Step 1. Remove the front cap (unclip)
Open the glovebox and take off the front cap.
Step 2. Remove the control panel (unclip)
Take off the control panel and unplug the connector.
Motrade December 2023 ©
Step 3. Remove the air vents (unscrew)
Unscrew the two screws (crosshead) that hold the air vents. Take of the air vents and
unplug the connector. Be careful, do not force. At the left corner there is a little
obstruction. Just wiggle a bit to disconnect the vents.
Step 4. Remove the bezel of the screen (unclip)
Start at the narrow part of the bezel and work towards the screen. Unclip the bezel.
Disconnect the connector. Be careful, do not force. At the corner near the ignition a
little part of the bezel is behind the frame of the car (see red arrow in the picture
below).
Motrade December 2023 ©
Step 5. Remove the screen (unscrew)
Unscrew the screen. In total there are 4 10 mm bolts (not the bolts behind the
screen!). Place a blanket on the middle console to avoid scratches. Pull the screen
towards you.
Step 6. Prepare the cable
Lead the main cable from the glovebox to the screen (if you want to hide it in the
glovebox) or find another place for the interface.
Motrade December 2023 ©
Step 7. Connect the three connectors
Disconnect the three connectors from the screen/radio. Reconnect them to the new
contra-connectors from the cable. Connect the three connectors from the interface
cable to the screen/radio.
Step 8. Reinstall the screen/radio
Push back the screen/radio and fasten the 4 bolts.
Step 9. Test the system
Connect the interface and the USB-cable. Read the manual to choose the right
position of the dipswitches. Choose AUX as a source for sound in the original system.
Switch to the interface by long-pressing Siri-button, MODE button or AUX.
Remove and forget the existing bluetooth connection with the car.
Connect the phone to the bluetooth signal of the interface and put WIFI on.
The bluetooth connection will create a WIFI-network and disconnect itself after that.
Test the system with regard to graphics, sound, switching between radio and
interface and reverse.
Motrade December 2023 ©
The image is a bit blurry. There is no way to avoid this because it’s an analogue video
signal. It does not affect the functionalities.
Step 10. Reconnect all parts
Reconnect all parts in reverse order. Dont forget the connectors of the air-vents, the
bezel and the control panel.
Step 11. Enjoy!
This manual has been compiled on the basis of experience and with due care. No
rights can be derived from it. Improvement tips / tricks are of course always welcome!
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

MoTrade C-HR Installation guide

Type
Installation guide

MoTrade C-HR is an innovative interface that transforms your Toyota C-HR's infotainment system into a versatile hub for smartphone connectivity and multimedia enjoyment. With CarPlay and Android Auto compatibility, you can seamlessly integrate your mobile device, accessing navigation, music, messaging, and a wide range of apps directly from your car's display. The interface also supports Bluetooth connectivity, allowing you to make hands-free calls and stream audio wirelessly. Installation is straightforward, and the included detailed instructions guide you through the process step by step.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI