mTrade Evoque 2015-2017 Operating instructions

Brand
mTrade
Model
Evoque 2015-2017
Category
Car kits
Type
Operating instructions

The mTrade Evoque 2015-2017 seamlessly integrates CarPlay and Android Auto into your Range Rover Evoque, allowing you to access your favorite apps, music, and navigation directly from your vehicle's touchscreen. With a simple plug-and-play installation, you can enjoy a wide range of features without the need for any programming.

The mTrade Evoque 2015-2017 seamlessly integrates CarPlay and Android Auto into your Range Rover Evoque, allowing you to access your favorite apps, music, and navigation directly from your vehicle's touchscreen. With a simple plug-and-play installation, you can enjoy a wide range of features without the need for any programming.

Motrade December 2022 ©
Installation instruction for Carplay Android Auto interface
Range Rover Evoque 201 5-2017 with touchscreen
The interface is connected via a connection plug on the radio. It is
estimated that it takesabout 30-45 minutes of work to connect the interface. No
programming is necessary.
Step 1 Disconnect the battery
To be on the safe side, disconnect the battery first. In that case, make sure that the
locks no longer work!
Step 2. Remove narrow plastic parts next to the center console (unplug)
Snap off both narrow plastic parts next to the center console. Two torx screws are
released (size 30).
Step 3a. System WITH CD-player (beneath the screen)
Remove center console (screws and unplug)
Remove the two torx screws (size 20) on the bottom of the center console. Then plug
the center console off. Disconnect three rectangular plugs on both sides and in the
middle (tabs press and pull). Note: the plug in the middle has an extra locking. First
pull this (red) lock first out a bit. Set the console aside or rotate it so that you can pull
the radio forward.
Motrade December 2022 ©
Remove the radio (screws)
Unscrew the radio and pull it forwards. Place the interface under the radio.
The CarPlay interface comes approximately at the location of the red shaded
compartment in the center console.
Step 3b. System WITHOUT CD-player (radio beneath the passenger seat )
https://youtu.be/8UBlKyEJ0M8
Motrade December 2022 ©
Step 4. Connect the interface (plug in)
Connect the big black connector and the videocable labeled "to OEM radio" to the
radio. Connect the released video cable to the video cable labeled "to OEM monitor".
Connect the WIFI antenna, the purple and blue video plugs and the white powerplug
to the interface.
Step 5. Prepare for testing
Choose AUX as a source for sound in the OEM-system.
Remove the existing bluetooth connection with the car.
Connect the phone to the bluetooth signal of the interface and put WIFI on.
The bluetooth connection will create a WIFI-network and disconnect itself after that.
Step 6. Test the system (operation)
Test the system with regard to graphics, sound, switching between radio and
interface and reverse switching. Activate the system via the HOME button.
The dip switches are standard at 00010000 (0 = OFF, 1 is ON).
In case the display is shifted, try 000 00000 or 00001000. After modification, pull out
the power plug and put it back in.
Step 7. Close the system again (clicks, screws)
Step 8. Enjoy!
This manual has been compiled on the basis of experience and with due care. No
rights can be derived from it. Improvement tips / tricks are of course always welcome!
(motra[email protected])
Motrade December 2022 ©
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

mTrade Evoque 2015-2017 Operating instructions

Brand
mTrade
Model
Evoque 2015-2017
Category
Car kits
Type
Operating instructions

The mTrade Evoque 2015-2017 seamlessly integrates CarPlay and Android Auto into your Range Rover Evoque, allowing you to access your favorite apps, music, and navigation directly from your vehicle's touchscreen. With a simple plug-and-play installation, you can enjoy a wide range of features without the need for any programming.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents