MoTrade AURIS 2014-2019 User manual

Type
User manual

MoTrade AURIS 2014-2019 enables you to connect your CarPlay or Android Auto enabled device to your car's infotainment system. It supports various features including navigation, music playback, and hands-free calling. The interface connects via the radio connectors and doesn't require any programming. Installation involves removing the display, routing the cable, connecting the connectors, testing the system, and reconnecting all components. Enjoy an enhanced driving experience with seamless integration of your smartphone's features.

MoTrade AURIS 2014-2019 enables you to connect your CarPlay or Android Auto enabled device to your car's infotainment system. It supports various features including navigation, music playback, and hands-free calling. The interface connects via the radio connectors and doesn't require any programming. Installation involves removing the display, routing the cable, connecting the connectors, testing the system, and reconnecting all components. Enjoy an enhanced driving experience with seamless integration of your smartphone's features.

MoTrade
April 2023 ©
Installation instruction for Carplay Android Auto interface
Toyota AURIS 201 4-2019
The interface is connected via the connectors of the radio. It is
estimated that it takes 15-30 minutes of work to connect the interface. No
programming is necessary.
Step 1. Click the panel around the screen
Carefully pull off the frontpanel and disconnect the connectors.
MoTrade
April 2023 ©
(First unclip the little side panel left)
Step 2. Remove the display (unscrew)
Unscrew the screen. In total there are 2 or 4 bolts of 10 mm. Place a blanket on the
center console to avoid scratches. Pull the screen towards you.
Step 3. Prepare the cable
Route the main cable from the glove compartment to the screen (if you want to place
it in the glove compartment) or find another place for the interface.
MoTrade
April 2023 ©
Stap 4. Connect the three connectors
Disconnect the three plugs from the screen/radio. Reconnect themto the cable
counter-connectors. Connect the three connectors of the interface cable to the
screen/radio.
Step 5. Install the screen/radio
Pull back the screen/ radio and attach the 4 bolts.
Step 6. Test the system
Connect the interface and the USB cable. Read the manual to choose the correct
position of the dip switches. Choose AUX as the source for sound in the original
system. Switch to the interface by long pressing the Siri button, MODE button, or
AUX.
Remove and forget the existing bluetooth connection to the car.
Connect the phone to the bluetooth signal of the interface and turn on WIFI.
The bluetooth connection creates a WIFI network and then disconnects itself.
Test the system with respect to graphics, sound, scchopping between radio and
interface and backwards.
MoTrade
April 2023 ©
Step 7. Reconnect all components
Reconnect all components in reverse order. Don't forget to plug back in the front
panel plugs.
Step 8. Have fun!
MoTrade
April 2023 ©
This manual has been compiled on the basis of experience and with the necessary
care. No rights can be derived from it. Improvement tips/tricks are of course always
welcome! ([email protected])
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

MoTrade AURIS 2014-2019 User manual

Type
User manual

MoTrade AURIS 2014-2019 enables you to connect your CarPlay or Android Auto enabled device to your car's infotainment system. It supports various features including navigation, music playback, and hands-free calling. The interface connects via the radio connectors and doesn't require any programming. Installation involves removing the display, routing the cable, connecting the connectors, testing the system, and reconnecting all components. Enjoy an enhanced driving experience with seamless integration of your smartphone's features.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI