CNB SxB2xZ12F P User manual

Brand: CNB

Model: SxB2xZ12F P

Category: Security cameras

Type: User manual

This manual is also suitable for

SxB2xZ12F N

Compact PTZ Dome Camera SxB2xZ12F(N/P)

User’s Manual Ver 1.2 (3810-0287A2)

www.cnbtec.com

Compact PTZ Dome Camera SxB2xZ12F(N/P)

User’s Manual Ver 1.2

www.cnbtec.com

This lightning flash with arrowhead symbol is intended to alert the

user to the presence of un-insulated "dangerous voltage" within the

product's enclosure that may be of sufficient magnitude to constitute

a risk of electric shock to persons.

◎ Read all of the safety and operating instructions before using the product.

◎ Save these instructions for future reference.

◎ Do not use attachments or accessories unless recommended by the appliance

manufacturer as they may cause hazards, damage product and void warranty.

◎ Do not use this product near water or moisture.

◎ Do not place or mount this product in or on an unstable or improperly supported location.

Improperly installed product may fall, causing serious injury to a child or adult, and

damage to the product. Use only with a mounting device recommended by the

manufacturer, or sold with the product. To insure proper mounting, follow the

manufacturer's instructions and use only mounting accessories recommended by

CAUTION : TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT OPEN COVERS.

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICEING TO QUALIFIED SERVICE PERSONAL.

CAUTION

RISK OF ELECTRIC

SHOCK DO NOT OPEN

Important Safeguard

Warnings

Cautions

a risk of electric shock to persons.

This exclamation point symbol is intended to alert the user to the

presence of important operating and maintenance (servicing)

instructions in the literature accompanying the appliance.

WARNING : TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK HAZARD,

DO NOT EXPOSE THIS CAMERA TO RAIN OR MOISTURE.

manufacturer's instructions and use only mounting accessories recommended by

manufacturer.

◎ This product should be operated only from the type of power source indicated on the

marking label.

◎ Before using, make sure power supply and others are properly connected.

◎ While operating, if any abnormal condition or malfunction is observed, stop using the

camera immediately and then contact your local dealer.

◎ Do not disassemble or tamper with parts inside the camera.

◎ Do not drop or subject the camera to shock and vibration as this can damage camera.

◎ Care must be taken when you clean the clear dome cover. Especially, scratch and dust

will ruin your quality of camera.

◎ Do not install the camera in areas of extreme temperature, which exceed the allowable

range.

◎ Avoid installing in humid or dusty places.

◎ Avoid installing in places where radiation is present.

◎ Avoid installing in places where there are strong magnetic fields and electric signals.

◎ Avoid installing in places where the camera would be subject to strong vibrations.

◎ Never expose the camera to rain and water.

Precautions

Features

Product

Installation

Operation

Check points before operation ------------------------------------------------------------------ 20

Preset and Pattern Function Pre-Check ------------------------------------------------------ 20

Each protocol function number ------------------------------------------------------------------- 20

Starting OSD Menu --------------------------------------------------------------------------------- 21

Reserved Preset

-------------------------------------------------------------------------------------

------------------------------------------------- 6 -------------------------------------------- 26

General Rules of Key Operation for Menu ---------------------------------------------- 26

MAIN MENU ------------------------------------------------------------------------------------- 26

DISPLAY SETUP ------------------------------------------------------------------------------- 27

CAMERA SETUP ------------------------------------------------------------------------------ 28

MOTION SETUP ------------------------------------------------------------------------------- 32

PRESET SETUP ------------------------------------------------------------------------------- 34

SWING SETUP --------------------------------------------------------------------------------- 36

PATTERN SETUP ----------------------------------------------------------------------------- 36

GROUP SETUP -------------------------------------------------------------------------------- 37

SYSTEM INITIALIZE -------------------------------------------------------------------------- 40

------------------------------------------------- 8

------------------------------------------------- 9

------------------------------------------------- 20

Specifications

----------------------------------

Reserved Preset

-------------------------------------------------------------------------------------

PRESET ----------------------------------------------------------------------------------------------- 21

SWING ------------------------------------------------------------------------------------------------- 22

PATTERN --------------------------------------------------------------------------------------------- 22

GROUP ------------------------------------------------------------------------------------------------- 23

Others Functions ------------------------------------------------------------------------------------ 24

OSD Display of Main Screen --------------------------------------------------------------------- 25

Specifications

----------------------------------

◎ 1/4'' High Sensitivity CCD

◎ x12 Optical Zoom, x12 Digital Zoom(Max x144)

◎ Day & Night, BLC (Backlight Compensation), WDR(Wide Dynamic Range),

ECL(Eclipse)

◎ Auto-Focus, Manual Focus, Semi-Auto Focus.

◎ Multi language OSD.

◎ 360°/sec high-speed movement to preset position.

◎ Simultaneous pan/tilt action when moving to preset locations for fast and natural

view transition.

◎ Low speed 0.05°/sec. joystick movement for accurate operation. The joystick speed

automatically changes as the zoom rate changes for easier operation.

◎ Up to 255 cameras can be connected in the same network.

◎ Pelco-D, Pelco-P, and BOSCH protocol can be used.

◎ Various camera functions can be configured through the OSD (On Screen Display)

Menu.

◎ Information such as Camera ID, Pan/Tilt location, Direction, Alarm In/Output, Preset

can be displayed.

Video Specification

Pan/Tilt Control

Multi-Language OSD Menu

PTZ Control

Alarm In/Output

automatically changes as the zoom rate changes for easier operation.

◎ 127 preset locations can be stored, and each preset location can have its own image

settings and label.

◎ 8 Swing functions. (continuously swinging in between 2 pre-set locations back and

forth)

◎ 4 Patterns (Saves specific Joystick operations and endlessly repeats them.)

◎ 8 groups (running a combination of up to 20 preset/pattern/ swing actions saved by

the user in sequence)

※ Maximum numbers for each function differs in each protocol

(Refer to “Function numbers in each protocol”, Page 59)

◎ There are 4 Alarm Inputs and one alarm output.

◎ In order to filter out the external noise, use a port coupling at the input and a relay

at the output.

◎ The sensor can be set to Normaly Open or Normaly Close

◎ Sensor inputs can be DC 5~12V.

◎ Relay output can be up to AC 125V/0.5A or DC 24V/1A.

◎ A Sensor input can be configured to move the PTZ to any preset location.

Preset, Pattern, Swing, Group

◎ A numeric Camera ID can be set by the DIP switch, and the values for each switch

position are like the following:

- To set up the Camera ID, remove the lid at the

bottom of the camera by unscrewing the three screws

marked with arrows.

Basic Contents

Camera ID Set Up

•Camera

•Dome Cover

•Camera with Sunshield

•L wrench-1EA

• Maximum 255 IDs can be used from 1 to 255. Do not use address 0.

• The default address is 1.

• When using a Keyboard type controller, make sure that the address set in the

keyboard matches the camera’s ID before controlling.

Optional Contents

Pin 1 2 3 4 5 6 7 8

ID Value 1 2 4 8 16 32 64 128

ex) ID=5 on off on off off off off off

ex) ID=10 off on off on off off off off

•Rubber gasket

•Installation Guide

•Manual

•PLASTIC ANKER

And mounting

bolt set 3EA

•DC or AC Adaptor

•Rubber Gasket for

Wall Mount Bracket

•Wall Mount Bracket

•Installation Guide

•Screws

•L wrench-2EA

◎ The forth DIP switch position sets the termination Impedance on the camera.

◎ When the controller is far away from the camera (1:1 connection)

- An impedance mismatch can happen when the controller is far from the camera.

Set the termination impedance on the camera as well as the controller to match

the impedance.

◎

When connecting many cameras in the same network.

◎ The three DIP switch positions shown below sets the communication protocol.

Communication Protocol Termination Impedance

Use the termination Impedance in the following cases:

1 2 3 4

NO PROTOCOL BAUDRATE #1 #2 #3

0 PELCO-D 2400bps OFF OFF OFF

1 PELCO-D 9600bps ON OFF OFF

2 PELCO-P 4800bps OFF ON OFF

◎

When connecting many cameras in the same network.

- The signal loss can happen when too many cameras are connected to the same

network. Set the termination impedance on the furthest camera only as well as

the controller. Do not turn on the termination impedance on other cameras.

◎ On the controller (Keyboard-type or DVR), make sure the same protocol and

baud rate are selected before controlling.

◎ Turn the camera’s power off before changing the protocol setting.

PELCO-P 9600bps ON ON OFF

4 BOSCH 9600bps OFF OFF ON

Others

Reserved

# 2# 1 # n

Keyboard Controller/DVR

RS-485

① Put the dome cover on the camera where the

marks on the casings line up. Tighten the 4

crews using the wrench supplied.

② Attach the rubber gasket to the surface mount

bracket and mount the bracket on the

installation surface using the screws provided.

④ Put the camera into the bracket where the

mark lines up with ‘unlocked’ (I) mark on

the bracket. Lock the camera in by slightly

turning it clockwise.

⑤ Make sure to turn the camera to the

position where the mark on the camera

lines up with ‘locked’ (II) mark on the

Installation

Installation of a basic type PTZ

③ Attach the service wire. Power & video connect

the cables.

☞ Attach the service wire properly to avoid

dropping the product to the ground.

lines up with ‘locked’ (II) mark on the

bracket.

⑥ Tighten the locking screw on the

opposite side using the L wrench. Remove

the protection cover from the dome cover.

The installation is now complete.

•With Sunshield

•Without Sunshield

Installation with a Wall Mount Bracket

① Attach the rubber gasket and Sunshield*

or Surface Mount bracket on the

Wall Mount bracket using the

screws provided.

☞ Applicable only when using

the Sunshield.

④ Put the camera into the bracket

where the mark lines up with

‘unlocked’ (I) mark on the bracket.

Lock the camera in by slightly turning

it clockwise.

⑤

Make sure to turn the camera to the

② Mount the wall mount assembly on

a wall using the bolts provided.

③ Attach the service wire. Power & video

connect the cables.

☞ Attach the service wire properly to

avoid dropping the product to the

ground.

⑤

Make sure to turn the camera to the

position where the mark on the camera

lines up with ‘locked’ (II) mark on the

bracket.

⑥ Tighten the locking screw on the

opposite side using the L wrench.

Remove the protection cover from

the dome cover. The installation is

now complete.

◎ RS-485

- Connect the RS-485 devices such as a PTZ controller or a DVR to operate the PTZ

camera. Please connect parallel when connecting multiple cameras together.

Cable Connections

- ALARM Line

- CVBS

Keyboard Controller/DVR

◎ Power

- The power rating for this product is DC 12V/1A and AC 24V/1.5A.

Please check to make sure the power supply is rated at DC 12V and more than 1A

before connecting.

◎ Video Output

- Connect the video cable to camera’s video output cable (provided).

Input Power Allowable Range Current Draw

For DC 12V model

DC 12V ± 10%

For AC 24V model

AC 24V ± 10%

1.5A (When the Heater

is on)

- AC/DC Power

- 485 Line

◎ Check the sensor’s drive voltage and signal type before connecting.

◎ Maximum allowable power ratings for the output resistance are like the following:

Relay OutputSensor Input

Operating Voltage

Internal Circuitry

+ -

IN 1 -

IN 4 -

Sensor

IN COM +

+5V ~ 12V

Resistance

AC or DC

Internal Circuitry

OUT 1

Sensor

The sensor signal type can be Open Collector or Voltage Output, and the

connection has to be made accordingly.

◎ In order to use the sensor inputs, configure the sensor type in the OSD menu. The

Sensor Input type can either be Normaly Open or Normaly Closed. When this

is not configured properly, the alarm will operate the opposite way from

desired.

Connection

Function

COM+

Connect to (+) of the Sensor drive voltage.

IN1-, IN2-,

IN3- , IN4-

Connect to sensor signals.

Operating Voltage

Maximum Rating DC 24V, 1A AC 125V, 0.5A

Type Description

Normal Open The voltage is on at the sensor when the sensor is on.

Normal Close The voltage is on at the sensor when the sensor is off.

• Function : Using the OSD menu, you can configure the image settings or program

PTZ operations such as Preset, Pattern, Swing, and Group.

• Open : Go Preset [95] (Pelco® protocols only).

• Keys used : save the configurations using Focus NEAR button, and use Focus FAR

button to cancel. (All protocols)

• Reason : Reserved presets can be used when the controller does not have dedicated

menu buttons.

• Function :

◎ Check to see if all connections are made securely before connecting power.

◎ Make sure the camera’s ID matches the ID selected by the controller. The camera’s ID

is displayed on the screen, or you can check the Address DIP switch on the camera.

◎ Make sure both Camera and the controller are configured with the same protocol.

◎ Turn off the power before changing the protocol on the camera.

◎ Operation of a controller may be different depending on the manufacturer, so please

refer to the manual for your controller. Otherwise, this manual is written based on Pelco

standard protocol controller.

◎ First, see how to operate Preset and Pattern on your controller or DVR.

◎ In case of using Pelco standard protocol controller, the operation is like the following:

Installation Checklist

Preset and Pattern

OSD Menu

Presets reserved for special functions

Go Preset

Press [Preset No]

button and [Preset] button.

Go Preset [95] : Open OSD Menu (Pelco® protocols only).

Go Preset [131~134] : Run Pattern 1~4

Go Preset [141~148]

: Run Swing 1~8

• Description : Maximum 127 preset locations can be saved in between 1 to 128

except for 95 (Reserved for opening Menu). Each preset can have its own image

settings and label. When saving a preset location using the controller, a blank label

and global image settings will be saved. Use the OSD menu if you want to change

the settings of each preset. Preset locations can also be saved in the OSD menu.

• To Configure : Set Preset [1~128]

• To Run : Go Preset [1~128]

• To Delete : Presets can be deleted in the OSD Menu.

◎ Even if your controller does not have a Pattern button, all functions for the camera can

still be operated. Please refer to the ‘presets reserved for special functions’ section of this

manual.

Preset

Go Preset

Press [Preset No]

button and [Preset] button.

Set Preset Press [Preset No] button and press and hold the [Preset] button for

two seconds.

Run Pattern Press [Pattern No] button and [Pattern] button.

Set Pattern Press [Pattern No] button and press and hold the [Pattern] button

for two seconds.

Go Preset [141~148]

: Run Swing 1~8

Go Preset [151~158] : Run Group 1~8

Protocol

Function

Pelco® BOSCH

Preset

127 98

Swing

8 1

Pattern

4 2

Group

8 1

Protocol and Maximum numbers for each function

• Description : In Swing mode, the PTZ will continuously swing between two preset

positions. It will first move from the first position to the second clockwise, and then it will

go from the second position to the first counterclockwise.

If you set the first and the second position the same, the camera will continuously do

a 360

tour. The moving speed can be selected in between 1

/Sec and 180

/second.

• To Configure : Configure the pattern operations using either of the two following methods.

1) Set Pattern [Pattern No.]

- The screen shown in the figure will open.

- Operate the joystick or keyboard controller to move

the PTZ the way you want for the pattern.

- Remaining time to save the operation is displayed

on the bar.

- To finish the operation and save, press NEAR button. Or

press FAR button to cancel.

2) The same can be configured in the OSD Menu.

• To Run :

• To delete : A pattern can be deleted in the OSD Menu.

Swing

EDIT PATTERN 1

[NEAR:SAVE /FAR:DELETE ]

■■■■■■ ■■■■■■ ■■■■■■ ■

0/0/x1/N

1) Run Pattern [Pattern No.] ex) To run Pattern 2 : Run Pattern [2]

2) Go Preset [Preset No. + 130] ex) To run Pattern 2 : Go Preset [132]

1st Preset

2nd Preset

• To Configure : use the OSD menu.

• To Run :

• To Delete : A Swing can be deleted in the OSD Menu.

• Description: A Pattern saves and repeats a series of pan/tilt/zoom and preset

operations. A maximum four patterns can be saved, and maximum 1200 operations

can be saved in each pattern.

• Description : A Group saves and repeats a series of Preset, Pattern, and Swing actions.

A maximum 8 Groups can be saved, and each group can contain maximum 20 actions

(Preset, Pattern, or Swing). In a Group, a moving speed for Presets and repeat numbers for

Patterns and Swings can be configured. In addition, a hold time in between the operations

can also be configured.

• To Configure : Use the OSD Menu for configuration.

• To Run :

• To Delete : A Group can be deleted in the OSD Menu.

Pattern

Group

Preset 1 Pattern 1 Swing 1

Hold Time

Max. 20 Actions

1) Run Pattern [Swing No. + 10] ex) To run Swing 3 : Run Pattern [13]

2) Go Preset [Swing No. +140] ex) To run Swing 3: Go Preset [143]

1) Run Pattern [Group No. +20] ex) To run group 7: Run Pattern [27]

2) Go Preset [Group No. +150] ex) To run group 7: Go Preset [157]

• PWR UP ACTION : This function lets the PTZ camera continue to run the last

operation when an unexpected power reset happens. Preset, Pattern, Swing, and Group

is resumed, while a location manually moved by a joystick is not recovered.

• AUTO FLIP : This function flips the image when the Tilt angle goes over 90°.

The flipped image is indicated by a display of an ‘F’ on the screen.

When this function is not used, the Tilt angle limits are -5 and 95°

• PARKING ACTION : This function automatically starts a pre-configured preset operation

when the camera is not manually operated for a given time. "Wait Time“ can be

between 1 minute and four hours.

• ALARM I/O : There are four sensor Inputs and one Alarm output. The PTZ can go to a

pre-configured preset location when there is an alarm input. When there are multiple

Alarm inputs, the camera will respond to the latest Alarm Input.

• P/T/Z Information : This indicates the current Pan/Tilt/Zoom location as well as the

direction of the PTZ.

Other Main Features OSD Menu

• CAM ADJUST : Each preset can have its own WB(White Balance) and AE(Auto Exposure)

configuration. Either "Global" mode or "Local" mode can be selected. The WB/AE

values set in "ZOOM CAMERA SET" menu are the “Global” values, and the WB/AE

values set in each preset menu are the "Local" values. When a preset is loaded, its

"Local" image configuration values are automatically applied. When the preset

selection is cancelled by a joystick operation, the image configuration automatically

changes to “Global” values. The Local values configured at each preset menu will not

change even when the global values are changed.

• FOCUS MODE : This function automatically switches between Manual Focus and Auto

Focus. The Focus will be Manual in preset mode, and it changes to Auto upon a

manual Joystick operation. In a preset operation, recalling the saved focus location

makes the focus transition quick.

direction of the PTZ.

• Alarm Information : This indicates the status of Alarm Inputs and Output. The

number is displayed when there is an input or an output. No input or output is

displayed as '-‘.

For example) When Input 2, Input 3, and output 1 is on:

• Camera ID : Camera’s ID gets displayed here.

• Action Title : The followings are the information that is displayed in the Action Title.

• Preset Label : This displays the label saved at each preset

• Image Flip : In Auto Flip mode, this indicates the Flip status.

• IRIS Information : This indicates the Camera’s IRIS information.

I:-23- O:1

“SET PRESET xxx” When setting a preset location

“PRESET xxx” When moving to a preset location

“PATTERN x” When a pattern is operated

“SWGx/PRESET xxx” Swing number and Preset Number during a Swing

operation

“UNDEFINED” When an undefined operation is executed.

◎ ( ) indicates a sub-Menu.

◎ Press NEAR button to go into a sub menu.

◎ In any Menu, press FAR button to go to the previous screen.

◎ Use joystick or Up/Down and Left/Right button to move the cursor in the menu.

◎ To change parameter values, use Joystick Up/Down.

◎ Press NEAR button to save the configuration change, and press FAR button to

cancel the change.

• SYSTEM INFORMATION

- Displays product Information and configuration

status.

◎ Configures the main screen and sets North

direction

◎ Sets On/Off the display of each display items

- In ‘AUTO’, the information only gets displayed

when the configuration is being changed.

Menu Operation

Main Menu

OSD Setup

Display setup

status.

• DISPLAY SETUP

- Configures Display of OSD with its

Display items.

• DOME CAMERA SETUP

- Configures the camera functions

• SYSTEM INITIALIZE

- Recalls the default configuration values or

restarts the system.

when the configuration is being changed.

◎ Configures the North direction of the PTZ.

Move the PAN location to north direction and

press NEAR button to save.

Set North Direction

• CAMERA ID : [ON/OFF]

• PTZ INFORMATION : [ON/OFF/AUTO]

• ACTION TITLE : [ON/OFF/AUTO]

• PRESET LABEL : [ON/OFF/AUTO]

• ALARM I/O : [ON/OFF/AUTO]

• LANGUAGE : ENGLISH / SPANISH / CZECH

/ RUSSIAN / TURKISH / KOREA

/ PORTUGUESE / CHINESE

◎ Sets the Configuration of the Zoom Camera

module.

• FOCUS MODE [AUTO/MANUAL/SEMIAUTO]

- Configures the Focus Mode. In SemiAuto

Mode, the focus will only change to Manual

when a preset is loaded. Otherwise, it will

always be Auto.

• DIGITAL ZOOM [ON/OFF]

- Turns Digital Zoom On/Off

• IMAGE FLIP [ON/OFF]

- Flips the image vertically and horizontally.

• LINE LOCK

[ON/OFF]

◎ Configures the image parameters.

• STABILIZER [ON/OFF]

- This stabilizes the image when the camera is

wobbled or wavered.

• SHARPNESS [0~100]

- Adjusts the sharpness of the image

• GAMMA [CRT/LCD]

- Adjusts the gamma gain value to optimize the

image for monitor types.

Zoom Camera Setup

IMAGE ADJUST

• LINE LOCK

[ON/OFF]

- Turn this feature On to synchronize the image with the AC Power’s input

frequency. (Only used in AC Model.)

• WB MODE [ATW/AWB/MANUAL]

- In Manual Mode, RED and BLUE level can be

adjusted manually.

- AWB : This automatically adjusts the white balance.

(3000k~6000k)

- ATW : 2000k~10000k

• RED ADJUST [-100~100]

• BLUE ADJUST [-100~100]

WHITE BALANCE

• BACKLIGHT [OFF/BLC/WDR/ECL]

- BLC : Back light compensation

- WDR: Wide Dynamic Range Processing

- ECL : Eclipses. This masks off the brightest spot.

• DAY/NIGHT [AUTO/DAY/NIGHT]

- AUTO : Automatic Day/Night switching.

In AUTO Mode, a light level for switching can

be selected. The higher sensitivity level

causes the switching at lower light level.

• BRIGHTNESS [0~100]

- Sets the Image’s normal brightness level. The values for Iris, Shutter Speed, and Gain

will be based on this level.

※ Below is the reference table for various AUTO EXPOSURE functions.

AUTO EXPOSURE

3D-DNR Day&Night BACKLIGHT

Exposure ON OFF Auto D&N OFF WDR ECL BLC

IRIS

Auto O O O O O O O O

Manual O O O O O X O O

Shutter

Auto O O O O O O O O

A-FLK O O O O O O O O

Manual O O O O O X O O

OFF O O O O O X O O

High O O O O O O O O

• IRIS [AUTO/MANUAL(0~100)]

- In Auto Iris mode, the AE (Auto Exposure) is mainly controlled by the Iris value, while

the Shutter Speed is fixed. In Manual Iris Mode, the Iris is fixed, and the AE is mainly

controlled by other parameters.

• SHUTTER SPEED [OFF/AUTO/A-FLK/MANUAL(x128~1/90000 Sec]

- In Manual Iris (AUTO Shutter Speed) mode, the Shutter Speed mainly controls the

Auto Exposure. In A.Flicker(A-FLK) Mode, the Shutter Speed is set to 1/120 in NTSC

and 1/100 in PAL to avoid flickering.

• AGC [OFF/LOW/MIDDLE/HIGH]

- When the image gets darker than a certain level, the signal’s gain value increases to

make it brighter.

• 3D-DNR [OFF/LOW/MIDDLE/HIGH]

- Configures the 3D Digital Noise Reduction level.

• SENS-UP [x2~x128/OFF]

- Sets the maximum number of frame overlays at low light.

AGC

Middle O O O O O O O O

Low O O O O O O O O

OFF X O X O O X O O

◎ This menu configures all Motion functions of the

PTZ.

. • MOTION LOCK [ON/OFF]

- When the Motion Lock is on, users can only run

Preset, Swing, Pattern, and groups. Those

functions can not be deleted or edited.

However, all other OSD menu can be accessed

and changed.

• PWR UP ACTION [ON/OFF]

- Please refer to “Other Functions”

• AUTO FLIP [ON/OFF]

Please refer to “Other Functions

”

◎ This function automatically runs a pre-configured

operation when the camera is not in use for the

configured "Wait Time“.

• PARK ENABLE [ON/OFF]

• WAIT TIME [1 min.~4 hours]

- Gets displayed in “hh : mm : ss” format, and it

can be incremented by minutes.

• PARK ACTION [HOME/PRESET/PATTERN/SWING/GROUP]

- "HOME" would bring the PTZ location to the

initial position when the camera is not in

operation for the given time.

Motion Setup

PARKING ACTION Setup

Please refer to “Other Functions

”

• JOG MAX SPEED [1°/Sec~360°/Sec]

- Sets the maximum speed of the joystick operation. Zoom speed gets reduced in

higher magnifications for easy controlling.

• JOG DIRECTION [INVERSE/NORMAL]

- In Inverse mode, the screen moves to the same direction with the Joystick. In Normal

mode, the screen moves to the opposite direction from the Joystick.

• FRZ IN PRESET [ON/OFF]

- Turn this on to freeze the image while the PTZ moves to a preset location.

operation for the given time.

◎ This configures preset operations in response

to Alarm inputs.

• ALARMx TYPE [NORMAL OPEN/CLOSE]

- Configures Normal types for each Alarm input

• ALARMx ACTION [NOT USED/PRESET 1~128]

- Activate desired Alarm inputs and enter which

preset location to be loaded.

ALARM INPUT Setup

• PRESET NO. [1~128]

- Select a Preset No. to configure.

When the number already contains a location,

the PTZ will move to the saved location and

display related information such as LABEL and

CAM ADUJUST values.

If an unused number is selected, "UNDEFINED“

will be displayed underneath the selected

preset number.

• CLEAR PRESET [CANCEL/OK]

- Deletes the preset number with its configuration parameters.

• EDIT SCENE

- Opens up a sub-Menu in which you can move the PTZ to a desired location and

save.

◎ Move the PTZ to a desired position using the

joystick.

◎ Press NEAR button to save the position.

◎ Press FAR button to cancel the Preset Position

Setup.

Preset Setup

Preset Label Setup

Preset Position Setup

save.

• EDIT LABEL

- Name the preset location to be displayed on the screen when the preset is loaded.

The Label can contain up to 10 characters.

• RELAY OUTPUT [ON/OFF]

- Turn this on to activate the Alarm relay output when the preset is loaded.

• CAM ADJUST [GLOBAL/LOCAL]

- Each preset location can have its own White Balance and AE configurations.

"GLOBAL“ indicates that the preset will have image parameters saved in "ZOOM

CAMERA SETUP" menu, and "LOCAL“ indicates that the preset will have its own

image parameters. When "LOCAL“ is selected, a menu to configure WB/AE will

open up.

◎ The blinking cursor indicates the location of the

character to be saved. The cursor automatically

moves to right when a character is selected.

◎ Select a character from the Character Map. Move

the cursor to desired character using the joystick

(LEFT/RIGHT/UP/DOWN) and press NEAR button

to select.

• Select (" ") for a space and select ("<-") for backspace.

◎ Once desired label is completed, go to "OK" using

the Joystick and press NEAR button to save. Otherwise,

select "CANCEL“ to exit.

(■ )

↑

The Cursor

2 3 4 5 6 7 8 9

ABC DEFGH I

KLM NOPQR S

UVWXYZa b c

e f g h i j k l m

opq r s t u v w

yz < >

▬

/ : .

Space

Backspace

• SWING NO. [1~8]

- Select a Swing No. to configure. The 1

and 2

Position will be displayed as “NOT USED”

if the swing number was not used before.

• 1st POS, 2nd POS [PRESET 1~128]

- Select two positions to Swing. When an unused

preset number is selected, "UNDEFINED“ will be

displayed.

◎ When a Swing is loaded, it will first move from the first position to the second clockwise,

and then it will go from the second position to the first counterclockwise. If you set the first

and the second position the same, the camera will continuously do a 360° tour.

• SWING SPEED

/Sec

~ 180

/Sec]

◎ Move the PTZ to a desired starting position. Press NEAR button to start recording

the pattern operation.

Press FAR Button to cancel the edit.

◎

The selected presets and joystick operations during this period will be saved in the

Swing Setup Edit Pattern

NEAR

• SWING SPEED

/Sec

~ 180

/Sec]

- Sets the Swing speed.

• CLEAR SWING [CANCEL/OK]

- Deletes the selected Swing Number.

• PATTERN NO. [1~4]

- Select a Pattern number to configure.

“UNDEFINED” is displayed underneath the Pattern

number when an unused pattern number is

selected.

• CLEAR PATTERN [CANCEL/OK]

- Deletes the selected pattern number.

• EDIT PATTERN

- Starts recording the pattern operations.

◎

The selected presets and joystick operations during this period will be saved in the

pattern. The time left to record the operations is displayed in the bar at the top of

the screen. 1200 operations can be saved in a pattern.

◎ Press NEAR button to finish and save the recording. Press FAR button to discard

recording and exit.

• GROUP NO. [1~8]

- Select a Group Number to configure.

“UNDEFINED” is displayed underneath the

Group No. when an unused number is selected.

• CLEAR GROUP [CANCEL/OK]

- Deletes the selected Group Number.

• EDIT GROUP

- Opens the Edit Group menu.

Pattern Setup

Group Setup

SWING SETUP

SWING NO .

2ND POS .

PRESET 5

NOT USED

1ST POS .

☞

UNDEFINED

Page is loading ...

CNB SxB2xZ12F P User manual

Brand: CNB

Model: SxB2xZ12F P

Category: Security cameras

Type: User manual

This manual is also suitable for

SxB2xZ12F N

Download PDF

report

CNB SxB2xZ12F P User manual

This manual is also suitable for

CNB SxB2xZ12F P User manual

Related papers

Other documents