Beghelli ATX-CT Installation guide

Brand: Beghelli

Model: ATX-CT

Type: Installation guide

Beghelli ATX-CT is a versatile and reliable emergency exit sign that provides clear and effective guidance in the event of a power outage. With its dual AC and universal DC power supply, the ATX-CT can be connected to various power sources, ensuring uninterrupted operation even during emergencies. Its self-powered option with a built-in Ni-Cd battery offers additional peace of mind, providing up to 90 minutes of emergency illumination.

The ATX-CT features a durable construction and is suitable for both indoor and outdoor use. Its compact design and easy installation make it ideal for a wide range of applications, including commercial buildings, schools, hospitals, and industrial facilities. The universal copy kit allows for easy customization of the exit sign's message, ensuring compliance with specific requirements.

ATX-CT

INSTRUCTIONS

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be followed including the following:

1. READ AND FOLLOW ALL SAFETY INSTRUCTIONS

2. Disconnect power before performing work on electrical equipment.

3. Do not use outdoors.

4. Do not let power cords touch hot surfaces and do not mount near gas or electric heaters.

5. Use caution when servicing batteries. Battery acid can cause burns to skin and eyes. If acid is spilled on skin or

eyes, ﬂush with fresh water and contact a physician immediately.

6. Equipment should be mounted in locations and at heights where unauthorized personnel will not readily

subject it to tampering.

7. The use of accessory equipment not recommended by Beghelli USA may cause an unsafe condition,

and will void the unit’s warranty.

8. Do not use this equipment for other than its intended purpose.

9. Servicing of this equipment should be performed by qualiﬁed service personnel.

10. SAVE THESE INSTRUCTIONS!

INSTALLATION

WALL MOUNT - SINGLE FACE:

1. Extend unswitched 24 hour AC supply of rated voltage to junction box or appropriate wiring (supplied by others).

Leave at least eight (8) inches of slack wire. The circuit should not be energized at this time.

2. Remove the exit sign faceplate (Figure 2).

3. Remove the exit sign universal copy kit.

4. Knock out the appropriate mounting pattern and/or wire pass-thru hole on the exit back plate to ﬁt the junction box or wiring

connector being used (supplied by others).

5. Bring wires through the back of the sign and mount the exit securely in place. Screw directly to junction box if possible.

6. Connect AC supply per diagram provided (Figure 5). Insulate unused wire!

CAUTION! - Failure to insulate unused wire may result in a shock hazard or unsafe condition as well as equipment failure.

7. Route wires and secure them in place.

8. Remove any directional chevron arrows to be indicated as required from the exit stencil.

9. Remove red ﬁbre, peel back off double sided tape to secure red ﬁbre.

10. Replace the exit faceplate together with red ﬁbre.

11. Turn on the AC voltage supply.

CEILING/END MOUNT - SINGLE OR DOUBLE FACE:

1. Follow steps 1 to 3 of Wall Mounting instructions above.

2. If double face is required then remove the backplate cover screw and slide the backplate down and out from exit frame. Exit signs

that are speciﬁed double face will already have the second/rear faceplate installed.

3. On the top and both sides of the exit there are three (3) holes for the canopy - two (2) for the mounting screws and

one (1) wire pass-thru hole. Knock out the three appropriate canopy mounting holes for your installation (Figure 3).

4. Secure the canopy to the exit sign using the supplied 1 inch screws and washer nuts and the snap wire pass-thru hole plastic

bushing into the wire pass-thru hole in the centre of the canopy (Figure 3).

5. Bring wires through the wire pass-thru and connect AC supply as described in step 6 of Wall Mounting instructions

above.

6. Secure the exit to the wall or ceiling using the supplied 1 1/2 inch screws and nuts. Screw directly to junction box if

possible. A universal spider plate is supplied to allow for exit sign placement adjustment or connection to a variety of electrical boxes

(Figure 4).

7. For double face exits install the second/rear faceplate.

8. Follow steps 7 to 10 of Wall Mounting instructions above.

SELF-POWERED:

1. For models ATX-SA, plug the battery into the circuit board per (Figure 5) self-powered sign.

926000185 04/14/2010

Beghelli U.S.A., 3810 Executive Way, Miramar, Florida, Tel: (954) 442-6600 Fax: (954) 442-6677

MAINTENANCE

1. Code requires that the equipment be tested every 30 days for 30 seconds, and that written records be maintained.

Further, the equipment is to be tested once a year for 90 minutes duration as per Code. The equipment is to be

repaired whenever the equipment fails to operate as intended during the duration test. Written records of test results

and any repairs made must be maintained. Beghelli USA strongly recommends compliance with all Code

requirements.

2. Clean exit face(s) on a regular basis.

NOTE: The servicing of any parts should be performed by qualiﬁed service personnel only. The use of replacement

parts not furnished by Beghelli USA, may cause equipment failure and will void the warranty.

SAVE THESE INSTRUCTIONS

Chassis GND LED Board

AC ONLY SIGN

Chassis GND

GREEN Ground

BLACK 120VAC

RED 347VAC or ORANGE 277VAC

WHITE Neutral

LED Board

AC & UNIVERSAL DC SIGN

YELLOW

Positive 6 to 24VDC

PURPLE Negative

Emergency Supply

FROM Battery Pack

SELF-POWERED SIGN

Chassis GND

24 hours

Unswitched Supply

GREEN Ground

BLACK 105 to 360V

WHITE Neutral

LED Board

DUAL UNIVERSAL AC SIGN

From Generator OR

Emergency Supply

BROWN 105 to 360VAC

BLUE Neutral

NOTE: Cap unused AC Wire!

24 hours

Unswitched Supply

GREEN Ground

BLACK 120VAC

RED 347VAC or ORANGE 277VAC

WHITE Neutral

24 hours

Unswitched Supply

Chassis GND LED Board

NOTE: Cap unused AC Wire!

GREEN Ground

BLACK 120VAC

RED 347VAC or ORANGE 277VAC

WHITE Neutral

24 hours

Unswitched Supply

Ni-Cd

Battery

Figure 4

Figure 1 Frame

Faceplate

Figure 2

Figure 3

Figure 5

Ceiling

Mount

End Wall

Mount

Remove chevrons/

arrows as required

Universal

Spiderplate

Electrical Junction Box

(supplied by others)

Install canopy kit as shown

if required

926000185

04/14/2010

Beghelli U.S.A., 3810 Executive Way, Miramar, Florida, Tel: (954) 442-6600 Fax: (954) 442-6677

Beghelli ATX-CT Installation guide

Beghelli ATX-CT Installation guide

Beghelli ATX-CT Installation guide

Related papers

Other documents