Beghelli WLX Installation guide

SELF-POWERED:

1. For SA models, plug the battery into the circuit board per (Figure 3) self-powered sign.

WLX

04/14/2010

CEILING/END MOUNT - SINGLE OR DOUBLE FACE:

1. Loosen the four (4) plastic screws (one in each corner) on the front cover / faceplate and then remove the faceplate.

For double face exits the other faceplate is attached from the inside with screws recessed behind the front ones.

2. Remove the canopy/nipple assembly by unscrewing the nut from the inside of the cabinet (Figure 4)

3. Feed the supply wires through the threaded nipple - leave at least 8 inches of slack wire.

4. Securely mount the canopy in place (mounting holes fit standard electrical boxes)

5. Mount the exit sign on the installed canopy, passing the threaded nipple and slack wires through the drilled hole.

6. Secure the exit sign to the threaded nipple using the supplied lock-washer and nut (Figure 4).

7. Connect voltage supply per diagram supplied (Figure 3). Insulate unused wire! CAUTION! - Failure to insulate

unused wire may result in a shock hazard or unsafe condition as well as equipment failure.

8. Route wires and secure them in place.

9. Peel the backing off the double sided tape from inside the cover. Select the pictogram, align and stick to the inside of

the cover.

10. Replace the cover and tighten the four (4) plastic screws.

11. Turn on the voltage supply.

WALL MOUNT - SINGLE FACE:

1. Loosen the four (4) plastic screws (one in each corner) on the front cover / faceplate and then remove the cover.

(Figure 1)

2. Install the four (4) mounting feet to the back of the cabinet (Figure 2)

3. Mount the exit securely in place using the four (4) mounting screw holes (one located in each corner -

screws not supplied).

4. Drill appropriate sized hole(s) in the enclosure for electrical entrance.

Use a rated watertight connector/conduit hub(s) to connect AC supply to the enclosure.

5. Pass power wires through previously drilled holes(s) and connector(s).

6. Connect supply per diagram provided (Figure 3). Insulate unused wire! CAUTION! - Failure to insulate unused

wire may result in a shock hazard or unsafe condition as well as equipment failure.

7. Route wires and secure them in place.

8. Peel the backing off the double sided tape from inside the cover. Select the pictogram, align and stick to the inside of

the cover.

9. Replace the cover and tighten the four (4) plastic screws.

10. Turn on the voltage supply.

INSTRUCTIONS

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be followed including the following:

1. READ AND FOLLOW ALL SAFETY INSTRUCTIONS

2. Disconnect power before performing work on electrical equipment.

3. Use caution when servicing batteries.

4. Equipment should be mounted in locations and at heights where unauthorized personnel will not readily subject it to

tampering.

6. Do not use this equipment for other than its intended purpose.

7. Servicing of this equipment should be performed by qualified service personnel.

8. SAVE THESE INSTRUCTIONS!

The use of accessory equipment not recommended by Beghelli USA, may cause an unsafe condition, and

will void the unit’s warranty.

Beghelli U.S.A., 3810 Executive Way, Miramar, Florida, Tel: (954) 442-6600 Fax: (954) 442-6677

234

Thisdocument is thepropertyof and contains information proprie

purpose for which it wasfurnished and returned upon request. Thi

otherwise inwhole orin part without priorauthorization of Beghell

agreement to the foregoing.

UNLESS OTHERWISE SPECIFIED

ALL DIMENSIONS = INCHES

ANGLES + 1/2

TOLERANCES:

.X = .020

.XX = .010

.XXX = .005

.XXXX = .003

3900 14Th. Avenue

MarkhamOntario

Tel. # 905 948-9500

email: sales@begh

Web: http://www.

DRAWN BY

SIZE SCALE

PART #

L D

A A

B B

C C

D D

Thisdocument is the propertyof and contains information proprietary to Beghelli Canada, Inc. It is submittedin confidence andis to be used solelyfor the

purpose for which it wasfurnishedand returned upon request. This document andsuch information is not to be reproduced, transmitted,disclosed, or used

otherwise inwhole or in part without prior authorization of Beghelli Canda, Inc. Therecepient's acceptanceof this document shall be consideredan

agreement to the foregoing.

UNLESS OTHERWISESPECIFIED

ALL DIMENSIONS = INCHES

ANGLES + 1/2

TOLERANCES:

.X = .020

.XX = .010

.XXX = .005

.XXXX = .003

3900 14Th. Avenue

Markham Ontario,L3R 4R3

Tel. # 905 948-9500 Fax# 905 948 8673

email: sales@beghellicanada.com

Web: http://www.beghelli.com

MATERIAL

FINISH

DRAWN BY DATE

SIZE SCALE

REV

SHEET

PART NAME

DWG NO

REF NO

DO NOT SCALE

2/23/2015

PART #

L D

MAINTENANCE

1. Code requires that the equipment be tested every 30 days, and that written records be maintained.

Further, the equipment is to be tested once a year for the required duration. The equipment is to be replaced or

repaired whenever it fails to operate as intended during the duration test. Written records of test results and any

repairs made must be maintained for presentation to the authority having jurisdiction. It is strongly recommended

to comply with all Code requirements.

2. The lamps listed herein when used according to the instructions with this unit are in accordance with the

requirements of CSA Standard C22.2, No. 141 – Unit Equipment for Emergency Lighting.

3. Clean faceplates/lenses on a regular basis.

CAUTION: Always turn off AC power before servicing. The servicing of any parts, should be performed by qualified

service personnel. The use of replacement parts not furnished and may cause

equipment failure and will void the warranty.

Chassis GND LED Board

AC ONLY SIGN

Chassis GND

GREEN Ground

BLACK 120VAC

RED 347VAC or ORANGE 200-277VAC

WHITE Neutral

LED Board

AC & UNIVERSAL DC SIGN

YELLOW Positive 6 to 24VDC

PURPLE Negative

Emergency Supply

FROM Battery Pack

SELF-POWERED SIGN

Chassis GND

24 hours

Unswitched Supply

GREEN Ground

BLACK 105 to 360VAC

WHITE Neutral

LED Board

DUAL UNIVERSAL AC SIGN

From Generator OR

Emergency Supply

BROWN 105 to 360VAC

BLUE Neutral

NOTE: Cap unused AC Wire!

24 hours

Unswitched Supply

GREEN Ground

BLACK 120VAC

RED 347VAC or ORANGE 200-277VAC

WHITE Neutral

24 hours

Unswitched Supply

Chassis GND LED Board

NOTE: Cap unused AC Wire!

GREEN Ground

BLACK 120VAC

RED 347VAC or ORANGE 200-277VAC

WHITE Neutral

24 hours

Unswitched Supply

Ni-Cd

Battery

TROUBLESHOOTING

EXIT SIGN DOES NOT COME ON AT ALL

1. Check AC supply and all AC connections - be sure exit has 24 hour AC supply (unswitched).

2. Check supply voltage and AC connections. The AC supply must be at least 80% of nominal (96V on a 120V line)

for equipment to function normally. At lower voltages the LEDs may begin to glow dimly until the source voltage

drops below the full “turn-on/off” point.

NOTE: This condition may also be caused by incorrectly connecting a voltage supply line

to the transformer lead.

3. If AC supply is OK; replace LED circuit board assembly.

SAVE THESE INSTRUCTIONS

Figure 1 Cover /

Faceplate

Cover Screws (4)

Cabinet /

Backbox

Figure 4

Mounting Feet

Screws (4)

Mounting Feet

Figure 2

Figure 3

Thisdocument is the propertyof and contains information proprietary to Beghelli Canada, Inc. It is submitted in confidence andis to be usedsolely for the

purpose for which it wasfurnished and returned upon request. This document and suchinformation is not to be reproduced, transmitted, disclosed, or used

otherwise inwhole ori n part without prior authorization of Beghelli Canda, Inc. The recepient's acceptance of thisdocument shallbe considered an

agreement to the foregoing.

UNLESS OTHERWISE SPECIFIED

ALL DIMENSIONS = INCHES

ANGLES + 1/2

TOLERANCES:

.X = .020

.XX = .010

.XXX = .005

.XXXX = .003

3900 14Th. Avenue

MarkhamOntario, L3R 4R3