Javad TRIUMPH-1 User manual

TRIUMPH-1
Brand
Javad
Model
TRIUMPH-1
Type
User manual

Javad TRIUMPH-1 is a versatile GNSS receiver designed for high-precision positioning and data collection. With its advanced technology, it offers accurate and reliable positioning solutions for various applications. The receiver features multiple connectivity options, including serial ports, USB, and Ethernet, allowing for easy data transfer and communication with external devices. It also supports Bluetooth and UHF/GSM antennas for wireless communication. The TRIUMPH-1 is equipped with an internal battery and can be connected to an external power source for continuous operation.

Javad TRIUMPH-1 is a versatile GNSS receiver designed for high-precision positioning and data collection. With its advanced technology, it offers accurate and reliable positioning solutions for various applications. The receiver features multiple connectivity options, including serial ports, USB, and Ethernet, allowing for easy data transfer and communication with external devices. It also supports Bluetooth and UHF/GSM antennas for wireless communication. The TRIUMPH-1 is equipped with an internal battery and can be connected to an external power source for continuous operation.

55
88.75
182*
L2 Up Offset: 98.05
L1 Up Offset: 93.25
1. All dimensions are in mm
2. * Reference dimension
3. ARP - Antenna Reference Point
SHMP - Slant Hei
g
ht Measurement Point
NGS ARP
SHMP
TRIUMPH-1
900 Rock Avenue, San Jose, CA 95131 USA
Phone: +1(408)770-1770 Fax: +1(408)770-1799
www.javad.com
Copyright © JAVAD GNSS, Inc., 2010
Download
• TRIUMPH-1 Operators Manual
• Latest firmware version
• USB driver
• NGS Information
http://www.javad.com/jgnss/products/receivers/triumph-1.html
TRIUMPH-1 is very simple to operate. Turn it on and
six green lights, one after the other, glow to tell you
that all is going well.
The ON/OFF button turns the receiver on and off.
FN button starts/stops data recording. Holding
both FN and ON/OFF buttons down for
more than 30 seconds will reset the
receiver. Holding FN down while
turning receiver ON using
ON/OFF button (or after
resetting receiver) until four
LEDs start to blink yellow
and than releasing FN
button while four LEDs still
blink yellow will bring
receiver to its initial factory-
default state (i.e., will clear
NVRAM).
• Power – used to connect the
receiver to an external
power source.
• Serial – used for
communication between
the receiver and an
external device.
• Ethernet - used to
connect the receiver to
local network.
• USB – used for high-speed
data transfer and communication
between the receiver and an
external device.
Communication with TRIUMPH-1 is easy. In
addition to two serial ports (A and B) and a USB,
TRIUMPH-1 also has Ethernet connectivity.
MinPad Connectors
To install the SIM card:
• Ensure the receiver is turned off.
• Open the small SIM card door.
• Open the SIM card holder.
• Carefully insert the SIM card into
the SIM card holder and push them
to LOCK to close it tightly.
SIM Card Slot
Function Symbol Green Yellow Red OFF
BATTERY 1Full Half Almost Empty OFF/No power
BLUETOOTH Connected Searching No connection Not Active
MODEM Connected Marginal
Connectivity No connection Not Active
SATELLITES28 or more 5 to 7 Less than 5 No Satellite
POSITION Fixed/Diff/
OK (Base) Float/No-Diff No Position Receiver OFF
RECORDING3Recording Less than 10 min
memory left Memory Full Not Active
TRIUMPH-1
Quick Start Guide
1. LED solid according to the battery means receiver is ON without external power. Blinking every 1 sec
according to the battery means external power is connected.
2. Effective number of satellites are total number of satellites tracked minus the number of non-GPS
systems tracked. For example if 8 GPS and 5 GLONASS are tracked the effective number of satellites is 12.
3. RECORDING LED blinks on each recording.
UHF/GSM Antenna
SHMP
Revision 1.6
April 10, 2012
  • Page 1 1
  • Page 2 2

Javad TRIUMPH-1 User manual

TRIUMPH-1
Brand
Javad
Model
TRIUMPH-1
Type
User manual

Javad TRIUMPH-1 is a versatile GNSS receiver designed for high-precision positioning and data collection. With its advanced technology, it offers accurate and reliable positioning solutions for various applications. The receiver features multiple connectivity options, including serial ports, USB, and Ethernet, allowing for easy data transfer and communication with external devices. It also supports Bluetooth and UHF/GSM antennas for wireless communication. The TRIUMPH-1 is equipped with an internal battery and can be connected to an external power source for continuous operation.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents