ALFAtron 20X-NDIC / W User manual

Brand: ALFAtron

Model: 20X-NDIC / W

Category: Security cameras

Type: User manual

This manual is also suitable for

www.alfatronelectronics.com

ALFATRON ELECTRONICS GmbH GERMANY

ALF-12X-NDIC, ALF-20X-NDIC, ALF-30X-NDIC

Full HD PTZ Camera User Manual

ALFATRON ALF-12X-NDIC, ALF-20X-NDIC and ALF-30X-NDIC

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

---Reorient or relocate the receiving antenna.

---Increase the separation between the equipment and receiver.

---Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

---Consult the dealer or an experienced radio/TV technician for help.

WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the

user's authority to operate the equipment.

Radiation Exposure

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two

conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the device.

"Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.

L'exploitation est autorisée aux deux conditions suivantes :

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,

même si le brouillage est susceptible d'en compromettre le fonctionnement."

Radiation Exposure:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment.

Déclaration d'exposition aux radiations: Cet équipement est conforme aux limites d'exposition aux rayonnements IC

établies pour un environnement non contrôlé.

Preface

This manual describes in detail the functions, installation and operation principles and methods of

the product. Before installing and using this product, please read it carefully.

1. Safety precautions

• During transportation, storage, installation and use, it is necessary to prevent heavy

pressure, severe vibration and immersion to avoid damage to products.

• The product shell is made of organic material. It is strictly forbidden to contact with

corroded liquid, gas or solid substances.

• Do not let the product get wet or rained on. Don't use it beyond the limit of temperature

and humidity.

• When cleaning the lens, please use a dry soft cloth to wipe. When there is a lot of dust,

please use a neutral cleaner and wipe gently.

• Do not use strong or corrosive detergents to avoid scratching the lens and affecting the

image.

• This product has no parts that users can repair by themselves, and the damage caused

by users ‘self-disassembly does not fall within the scope of warranty.

2. Electrical safety

• The installation and use of products must strictly comply with the national and local

electrical safety standards.

• Do not use power adapters beyond the specifications of the power supply, otherwise the

equipment components will burn out and will not work properly.

• In the process of using the product, we should keep enough distance from the high-

power equipment, and do a good job of lightning protection, surge protection and other

protective measures when necessary.

• When the product is not in use, please disconnect the power switch and

disconnect the power adapter from the power socket.

• The product uses DC 12V power supply, and the polarity of the power

plug is as shown in the picture.

ALFATRON ALF-12X-NDIC, ALF-20X-NDIC and ALF-30X-NDIC

3. Installation Safety

• Do not rotate the cylinder of the product by hand, otherwise it will destroy the rotating

shaft of the structure.

• Installation and placement of equipment should be horizontal and stable, and the

product should not be tilted, otherwise the picture may be skewed.

• Installation ensures that there are no obstacles in the rotating range of the platform to

prevent damage to the rotating shaft of the structure.

• Do not turn on power until all installation work is completed.

4. Magnetic Interference

• The electromagnetic field at a specific frequency may affect the local image. The

product is Class A product. Radio interference may occur in the home environment, and

users need to take appropriate measure.

Alfatron ALF-12X-SDIC and ALF-20X-SDIC

Content

1. Fast Installation ........................................................................................................................................ 2

1.1 Camera Interface Explanation ....................................................................................................................... 2

1.2 Power on initial configuration ....................................................................................................................... 2

1.3 Video Output.................................................................................................................................................. 2

2. Product overview ...................................................................................................................................... 5

2.1 Product Introduction ...................................................................................................................................... 5

2.1.2 Dimension ....................................................................................................................... 5

2.1.3 Accessory ............................................................................................................................. 5

2.2 Main Features ................................................................................................................................................ 6

2.2.1 Camera Performance ........................................................................................................... 6

2.2.2 Network performance ........................................................................................................... 6

2.3 Technical Specification .................................................................................................................................. 7

2.4 Interface Instruction ....................................................................................................................................... 8

2.4.1 External Interface.................................................................................................................. 8

2.4.2 Bottom Dial Switch ............................................................................................................... 9

2.4.3 RS-232 Interface................................................................................................................... 9

3. Application Instruction ............................................................................................................................. 10

3.1 Video Output................................................................................................................................................ 11

3.1.1 Power-On Initial Configuration ............................................................................................ 11

3.1.2 Video Output ........................................................................................................................ 11

3.2 Remote Controller ....................................................................................................................................... 11

3.2.1 Keys Instruction .................................................................................................................................. 11

3.2.2 Applications .......................................................................................................................... 12

3.3 MENU SETTING ........................................................................................................................................ 13

3.3.1 Main Menu ........................................................................................................................... 13

3.3.2 System Setting ..................................................................................................................... 14

3.3.3 Camera Setting .................................................................................................................... 14

3.3.4 P/T/Z .................................................................................................................................... 17

3.3.5 Video Format ....................................................................................................................... 18

3.3.6 Version ................................................................................................................................. 18

3.3.7 Restore Default .................................................................................................................... 18

4. Network Connection ...................................................................................................................................... 19

4.1 Connecting Mode .................................................................................................................... 19

4.2 IE Log In ...................................................................................................................................................... 21

4.2.1 Web client ............................................................................................................................ 21

2)Download/Install Plug in ............................................................................................................ 21

4.2.2 Preview ................................................................................................................................ 22

4.2.3 Playback .............................................................................................................................. 22

4.2.4 Configuration ....................................................................................................................... 22

4.2.5 Video configuration .............................................................................................................. 23

4.2.6 Network configuration .......................................................................................................... 24

4.2.7 System configuration ........................................................................................................... 25

ALFATRON ALF-12X-NDIC, ALF-20X-NDIC and ALF-30X-NDIC

4.2.8 Logout .................................................................................................................................. 26

5. Serial Communication Control ................................................................................................................ 26

5.1 VISCA protocol list ..................................................................................................................................... 26

5.1.1 Camera return command ..................................................................................................... 26

5.1.2 Camera control command ................................................................................................... 27

5.1.3 ,Inquiry command ................................................................................................................. 29

5.2 ,Pelco-D protocol command list ................................................................................................................... 31

5.3 Pelco-P protocol command list .................................................................................................................... 31

6. Camera Maintenance and Troubleshooting ............................................................................................ 32

6.1 Camera Maintenance ................................................................................................................................... 32

6.2 Troubleshooting ........................................................................................................................................... 32

7. Warranty .................................................................................................................................................. 34

Limited warranty in respect of Alfatron Products Only ................................................................................ 34

Alfatron ALF-12X-SDIC and ALF-20X-SDIC

1. Fast Installation

1.1

Camera Interface Explanation

Figure 1.1 Interface

1. Camera Lens

2. Camera Base

3. Remote Controller Receiver Light

4. Bottom Dial Switch

5. Tripod Screw Hole

6. RS232 Control Interface (input)

7. RS232 Control Interface (output)

8. RS485 Input (left +, right-)

9. Audio Input Interface

10. 3G-SDI interface

11. HDMI Interface

12. 10/100M Network Interface

13. DC12V Input Power Supply Socket

1.2

Power on initial configuration

1) Power on: Connect DC12V power supply adapter with power supply socket.

2) Initial configuration: Power on with power indicator light on and remote-control receiver light blinking, camera head moves

from bottom left to the bottom, and then goes to the HOME position (intermediate position of both horizontal and vertical),

while the camera module stretches. When remote control receiver light stops blinking, the self-checking is finished

Note: If you set preset 0, when Power on self-test is completed, the camera automatically moves to the preset 0 position.

1.3

Video Output

Video output from LAN, HDMI and 3G-SDI

1) Video Output from LAN

a. Network Cable Connection Port

b. Webpage Login: Open your browser and enter 192.168.5.163 in the address bar (factory default); press Enter to enter

the login page; click on the “player is not installed, please download and install!" and follow the installation steps for

installation. Then enter the username admin and password admin (factory default); press Enter to enter the preview

page, users can carry out PTZ control, video recording, playback, configuration and other operations.

2) HDMI Video Output

a. HDMI Video Cable Connection

b. Connect the camera and the monitor via HDMII video cable; video output is available after camera self-test.

3) 3G-SDI Video Output

a. 3G-SDI video cable connection

b. Connect the camera and the monitor via 3G-SDI video cable; video output is available after camera self-test.

ALFATRON ALF-12X-NDIC, ALF-20X-NDIC and ALF-30X-NDIC

1.4

Bracket mount

Note: Bracket can only be wall mounted or ceiling mounted on a concrete wall and cannot be installed on plasterboard.

1) Wall mount step

ALFATRON ALF-12X-NDIC, ALF-20X-NDIC and ALF-30X-NDIC

2. Ceiling mount steps

ALFATRON ALF-12X-NDIC, ALF-20X-NDIC and ALF-30X-NDIC

2. Product overview

2.1

Product Introduction

2.1.2

Dimension

Camera dimension

2.1.3

Accessory

When you unpack, check that all the supplied accessories are included:

Standard

1x Power adapter

1x RS232 cable

User manual

4x Double-side glue shim

1x IR Remote controller 1

piece

Wall / Ceiling mounting bracket

ALFATRON ALF-12X-NDIC, ALF-20X-NDIC and ALF-30X-NDIC

2.2

Main Features

2.2.1

Camera Performance

The ALF-NDIC series is a Full HD PTZ camera with either a 12x, 20x or 30x optical zoom lens. The features include

advanced ISP processing algorithms to provide vivid images with a strong sense of depth, high resolution, and fantastic

color rendition. It supports H.264/H.265 encoding which makes motion video fluent and clear even under less than ideal

bandwidth conditions

1. Superb High-definition Image: It employs 1/2.8-inch-high quality CMOS sensor. Resolution is up to 1920x1080 with

frame rate up to 60 fps.

2. Various Optical Zoom Lens: It has 5X/10X/12X/20X optical zoom lens for options. The 5X zoom lens is with 80.9 ° wide

view angle without distortion.

3. Leading Auto Focus Technology: Leading auto focus algorithm makes lens a fast, accurate and stable auto-focusing.

4. Low Noise and High SNR: Low Noise CMOS effectively ensure high SNR of camera video.

Advanced 2D/3D noise reduction technology is also used to further reduce the noise, while ensuring image sharpness.

5.Quiet PTZ: By adopting high accuracy step driving motor mechanism, it works extremely quiet and moves smoothly and

very quickly to designated position.

6. Multi-Format Video Outputs: support HDMI,3G-SDI, USB, wired LAN and wireless LAN interfaces

The 3G-SDI is available for 100m transmission at 1080p60 format.

7. Multiple Remote Controls: There is IR remoter and 2.4G wireless remote for options. The 2.4G wireless remote

controller will not be affected by angle, distance or IR interference. Support transparent transmission function.

8. Low-power Sleep Function: Support low-power sleep/wake up, the consumption is lower than 500mW under sleep

mode

9. Support Multiple Control Protocol: Support VISCA, PELCO-D, PELCO-P protocols which can also be automatically

recognized. Support VISCA control protocol through IP port.

10. RS-232 Cascade Function: ST series support RS-232 cascade function which is convenient for installing.

11.255 Presets Positions: Up to 255 presets (10 presets by remoter).

12.Wide Application: Tele-education, Lecture capture, Webcasting, Videoconferencing, Tele-training, Tele-medicine,

Interrogation and Emergency command systems.

2.2.2

Network performance

1. Audio Input Interface: Support 16000,32000,44100,48000 sampling frequency and AAC, MP3, PCM audio coding. Audio

input only embeds on the network stream. It does not embed on the HDMI or SDI Outputs of the camera.

2. Multiple Audio/Video Compression: Support H.264/H.265 video compression; AAC, MP3 and PCM audio

compression; Support compression of resolution up to 1920x1080 with frame up to 60 fps and 2 channel 1920x1080p

with 30 fps compression.

3. Multiple network protocol: Support ONVIF, RTSP, RTMP protocols and RTMP push mode, easy to link streaming

media server (Wowza, FMS)

ALFATRON ALF-12X-NDIC, ALF-20X-NDIC and ALF-30X-NDIC

2.3

Technical Specification

Model

ALF-12X-NDIC

ALF-20X-NDIC

ALF-30X-NDIC

Camera Parameter

Optical Zoom 12X

f＝3.9~46.8mm

20X

f＝5.5~110mm

30X

f＝4.3~129mm

Sensor 1/2.8-inch-high quality HD CMOS sensor

Effective Pixels 16: 9, 2.07 megapixel

Video Format HDMI/SDI

1080P60/50/30/25/59.94/29.97; 1080I60/50/59.94; 720P60/50/30/25/59.94/29.97

View Angle

6.3°(tele)

72.5°(wide)

3.3°(tele)

54.7°(wide)

2.34°(tele)

65.1°(wide)

F1.8 – F2.4

F1.6 – F3.5

F1.6– F4.7

Digital Zoom

10X

Minimum

Illumination

0.1Lux

DNR 2D & 3D DNR

White Balance Auto / Manual/ One Push/ 3000K/ 4000K/5000K/6500K

Focus Auto/Manual/One key focus

Aperture/Electron

ic Shutter

Auto/Manual

BLC ON/OFF

WDR OFF/ Dynamic level adjustment

Video Adjustment Brightness, Color, Saturation, Contrast, Sharpness, B/W mode, Gamma curve

SNR >55dB

Input / Output Interface

Video Interfaces SDI, HDMI, LAN (NDI & POE), RS232 (In & Out), RS485, A-IN

Video output interface HDMI, SDI, LAN,

Video Compression

Format H.264, H.265, Dual stream output

Control Protocol

VISCA/Pelco-D/Pelco-P;Baud Rate:115200/9600/4800/2400bps

Audio Input Interface

A-IN: Double track 3.5mm linear input;(Network Stream embedding only, does

not embed to HDMI or SDI outputs)

Audio Compression

Format

AAC/MP3/G.711A Audio compression

HD IP Interface

100M IP Port(10/100BASE-TX); Support VISCA protocol control through IP port.

Network Protocol

RTSP, RTMP, ONVIF, GB/T28181, NDI

Power Interface

HEC3800 Outlet (DC12V)

Supply Adapter

AC110V-AC220V to DC12V/1.5A

Input Voltage

DC12V±10%

Input current 1A (Max)

Consumption 12W (Max)

PTZ Parameter

Pan/Tilt Rotation ±170°, -30°～+90°

Pan Control Speed 0.1 -60°/sec

ALFATRON ALF-12X-NDIC, ALF-20X-NDIC and ALF-30X-NDIC

Tilt Control Speed 0.1-30°/sec

Preset Speed Pan: 60°/sec, Tilt: 30°/sec

Preset Number 255 presets (10 presets by remote controller)

Other Parameter

Storage temperature -10℃～+60℃

Storage humidity

20%

～

95%

Working temperature

-10

℃～

+50

℃

Working humidity

20%

～

80%

Dimension

150mmX150mmX167.5mm

Weight

1.4KG

Remote Operation (IP)

Remote Upgrade, Reboot and Reset

Accessories

Accessories (with

camera)

12V/1.5A power supply, RS232 cable, remote control, manual, warranty card,

Bracket

2.4

Interface Instruction

2.4.1

External Interface

1) External interface of ST models: RS232 Input /Output, RS485 Input, Audio Input,3G-SDI Output, HDMI Output,

LAN, DC12V Power Interface.

ALFATRON ALF-12X-NDIC, ALF-20X-NDIC and ALF-30X-NDIC

2.4.2

Bottom Dial Switch

Two DIP switches are set to ON or OFF to select different modes of operation as shown in Table 2.2

Table 2.2 Dial Switch setting

No.

SW1

SW2

Explanation

OFF

Working mode

OFF

Updating mode

2.4.3

RS-232 Interface

1) RS-232C interface specification as shown below

Computer or keyboard and camera connection method

Camera WindowsDB-9

1.DTR

1.DCD

2.DSR

2.RXD

3.TXD

4.GND

4.DTR

5.RXD

5.GND

6.GND

6.DSR

7.IR OUT

7.RTS

8.NC

8.CTS

9.RI

2) RS-232 Mini-DIN 8-pin Port Definition

ALFATRON ALF-12X-NDIC, ALF-20X-NDIC and ALF-30X-NDIC

Note: RS232 input and output interface, so you can cascade as shown above;

NO.

Port Definition

1 DTR Data Terminal Ready

DSR Data Set Ready

TXD Transmit Data

GND

System Ground

RXD Receive Data

6 GND System Ground

IR OUT

IR Commander Signal

No Connection

3) RS232 (DB9) Port Definition

NO.

Port

Definition

DCD

Data Carrier Detect

RXD

Receive Data

TXD

Transmit Data

DTR

Data Terminal Ready

GND

System Ground

DSR

Data Set Ready

RTS

Request to Send

CTS

Clear to Send

Ring Indicator

2) VISCA networking as shown below:

Camera cascade connection method

Camera 1

Camera 2

1.DTR

2.DSR

3.TXD

4.GND

5.RXD

6.GND

7.IR OUT

7.OPEN

8. NC

8.OPEN

3. Application Instruction

ALFATRON ALF-12X-NDIC, ALF-20X-NDIC and ALF-30X-NDIC

3.1

Video Output

3.1.1

Power-On Initial Configuration

Connecting the power, camera will have initial configuration, R indicator light will be flashing. When the camera return to the

HOME position (middle position for P/T), and lens finish zoom in/out, the auto-testing is finished. IR led will also stop

flashing. If the preset 0 is set, camera will rotate to the 0-preset position after initial configuration.

3.1.2

Video Output

Connect to the video output cable: the user selects the output mode.

1) network output: connect this product and your computer through the network cable, then open the browser, enter the

camera IP address (factory default 192.168.5.163) in the address bar, then to the login page and input a user name

and password (factory default are “admin”) ,Finally enter the preview page, and the image comes out.

(Note: If you forget your username, password, IP address, you can manually restore the default by the remote

controller key combination * #)

2) 3G-SDI output or (HDMI) output: Connect the monitor with the corresponding video output interface, then the monitor

output image.

3.2

Remote Controller

3.2.1 Keys Instruction

1. Standby Key

After 3S long press, the camera will step into standby mode. Long press 3S again, the

camera will self-test again and back to HOME position. (Note: If power-on mode is turned on

and Preset 0 is set, and there is no operation within 12s, it will automatically point to the

specified preset position.

2. Camera Address Selection

Select the camera address which wants to be controlled

3. Number Key

Set or run 0-9 presets

4, *, # Key

Key combination use

5. Focus Control Key

Auto Focus: Enter auto focus mode.

Manual Focus: The camera focus mode is manual

Switch the camera focus mode to manual focus by pressing [focus +] or [focus -] to adjust.

6. Zoom Control Key

Zoom＋: Lens near

Zoom－: Lens far

7. Set or Clear Preset key:

Set Preset: Set preset key + 0-9 number key:

Clear Preset key: Clear preset key + 0-9 number key

8. Pan/Tilt Control Key

Press Key: Up

Press Key: Down

Press Key: Left

Press Key: Right

“HOME” Key: Return to the middle position or enter the next level menu

9. BLC Control Key

Back Light ON / OFF: Turn on or off the back light

10. Menu Setting

Open or close the OSD menu

Enter / exit the OSD menu or return to the previous menu.

11. Camera IR Remote Control Address Setting

【*】+【＃】+【F1】:Camera Address No.1

【*】+【＃】+【F2】:Camera Address No. 2

ALFATRON ALF-12X-NDIC, ALF-20X-NDIC and ALF-30X-NDIC

【*】+【＃】+【F3】:Camera Address No. 3

【*】+【＃】+【F4】:Camera Address No. 4

12. Key Combination Functions

【

】

【

】

【

】

: Clear all presets

【

】

【

】

【

】

: Restore factory defaults

【

】

【

】

【

】

: Flip switch

【

】

【

】

+Auto: Enter the aging mode

5) 【*】+【#】+【3】: Menu set to Chinese

6) 【*】+【#】+【4】: Menu set to English

【

】

【

】

+Manual: Restore the default username,

password, and IP address

【

】

【

】

【

】

: Switch the video format to 1080P60

9)【#】+【#】+【1】: Switch the video format to 1080P50

10)【#】+【#】+【2】: Switch the video format to 1080I60

11)

【

】

【

】

【

】

: Switch the video format to 1080I50

12)

【

】

【

】

【

】

: Switch the video format to 720P60

13)【#】+【#】+【5】: Switch the video format to 720P50

14)【#】+【#】+【6】: Switch the video format to 1080P30

15)

【

】

【

】

【

】

: Switch the video format to 1080P25

16)

【

】

【

】

【

】

: Switch the video format to 720P30

17)【#】+【#】+【9】: Switch the video format to 720P25

3.2.2

Applications

Finishing initialization, it can receive and execute the IR commands. Press the remote controller button, the indicator

light is flashing; release the button, the indicator light stops flashing. Users can control the pan/tilt/zoom, setting and

running preset positions via the IR remote controller.

Key Instruction:

1. In this instruction, “press the key” means a click rather than a long-press, and a special note will be given if a long-

press for more than one second is required.

2. When a key-combination is required, do it in sequence. For example, “【 *】+【#】+【F1】” means press “【*】” first

and then press “【#】” and last press “【F1】”.

1) Camera Selection

Select the camera address to control.

2) Pan/Tilt Control

Up: press Down: press

Left: press Right: press

Back to middle position: press “【HOME】”

Press and hold the up/down/left/right key, the pan/tilt will

keep running, from slow to fast, until it runs to the endpoint;

the pan/tilt running stops as soon as the key is released.

3) Zoom Control

ZOOM IN: press “ZOOM “ key

ZOOM OUT: press “ZOOM ” key

Press and hold the key, the camera will keep zooming in or

zooming out and stops as soon as the key is released.

4) Focus Control

ALFATRON ALF-12X-NDIC, ALF-20X-NDIC and ALF-30X-NDIC

5) BLC

6) Pres

7) Camera Remote Controller Address Setting

3.3

MENU SETTING

【*】+【＃】+【F1】:Camera Address No.1

【*】+【＃】+【F2】:Camera Address No. 2

【*】+【＃】+【F3】:Camera Address No. 3

【*】+【＃】+【F4】:Camera Address No. 4

3.3.1

Main Menu

In normal working mode, press 【MENU】key to display the menu, using scroll arrow to point at or highlight the selected

items.

Setting

ets Setting, Running, Clearing

Focus (near): Press “

【

focus+

】

” key (Valid only in manual

focus mode)

Focus (far): Press “【focus-】”key (Valid only in manual focus

mode)

Auto Focus: Support

Manual Focus: Support

Press and hold the key, the action of focus will keep

continue and stops as soon as the key is released.

BLC ON / OFF: support

1. Preset setting: to set a preset position, the users should

press the “【SET PRESET】” key first and then press the

number key 0-9 to set a relative preset,

Note: 10 preset positions in total are available by

remote controller.

2. Preset Running: Press a number key 0-9 directly to run

a relative preset.

Note: Action in vain if a relative preset position is not

existed.

3. Preset clearing: to clear a preset position, the user can

press the “【CLEAR PRESET】” key first and then press the

number key 0-9 to clear the relative preset;

Note: press the “

【

】

” key three times continually to

cancel all the presets.

ALFATRON ALF-12X-NDIC, ALF-20X-NDIC and ALF-30X-NDIC

LANGUAGE: Language setting, Chinese / English

SETUP: System setting

CAMERA OPTION: Camera setting

PTZ OPTION: Pan tilt setting

VERSON: camera version setting

Restore Default: Reset setting

[↑↓] Select: for selecting menu

[← →] Change Value: for modify parameters

[MENU] Back: Press [MENU] to return

[Home] OK: Press [Home] to confirm

3.3.2

System Setting

Move the pointer to the (Setup) in the Main Menu, click the【HOME】key and enter into the (System Setting) as shown

below,

PROTOCOL: VISCA/Pleco-P/Pleco-D/Auto

Visca ADDR: VISCA=1~7 Pelco-P=1~255 Pelco-D = 1~255

Baud rate: 2400/4800/9600/115200

Visca Address Fix: On/Off

3.3.3

Camera Setting

Move the pointer to the (CAMERA) in the Main Menu, click the【HOME】key and enter the (CAMERA) as follow,

SETUP

＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝

Protocol Auto

Visca Address 1

Visca Address Fix OFF

PELCO-P Address 1

PELCO-D Address 0

Baudrate 9600

[↑↓]Select

Value

[← →]Change

＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝

Language

English

(Setup)

(Camera)

(P/T/Z)

(Video

Format)

(Version)

(Restore Default)

[ ↑↓ ]Select

Value

[ ← → ]Change

ALFATRON ALF-12X-NDIC, ALF-20X-NDIC and ALF-30X-NDIC

EXPOSURE

＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝

Mode Auto

EV OFF

BLC OFF

Anti-Flicker 50Hz

Gain Limit 3

WDR 5

[

↑↓

]Select [

← →

]Change

Value

EXPOSURE: Enter Exposure setting

COLOR: Enter color setting

Image: Enter into image setting

Focus: Enter into focus setting

Noise Reduction: Enter noise reduction

1) EXPOSURE SETTING

Move the pointer to the (EXPOSURE) in the Main Menu, click the【HOME】and enter the (EXPOSURE SET) as follow,

Mode: Auto, Manual, Shutter priority, Iris priority and Brightness priority.

EV: On/Off (only available in auto mode)

Compensation Level: -7~7 (only available in auto mode when EV is ON)

BLC: ON/OFF for options (only available in auto mode)

Anti-Flicker: OFF/50Hz/60Hz for options (only available in Auto/Iris priority/Brightness priority modes)

Gain Limit: 0~15(only available in Auto/ Iris priority /Brightness priority mode)

WDR: Off,1~8

Shutter

Priority:1/25,1/30,1/50,1/60,1/90,1/100,1/120,1/180,1/250,1/350,1/500,1/1000,1/2000,1/3000,1/4000,1/6000,1/10000(only

available in Manual and Shutter priority mode)

IRIS Priority: OFF, F11.0, F9.6, F8.0, F6.8, F5.6, F4.8, F4.0, F3.4, F2.8, F2.4, F2.0, F1.8(only available in Manual and Iris

priority mode)

CAMERA

＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝

(Exposure)

(Color)

(Image)

(Focus)

(Noise Reduction)

[↑↓]Select

Value

[← →]Change

Page is loading ...

ALFAtron 20X-NDIC / W User manual

Brand: ALFAtron

Model: 20X-NDIC / W

Category: Security cameras

Type: User manual

This manual is also suitable for

Download PDF

report

ALFAtron 20X-NDIC / W User manual

This manual is also suitable for

ALFAtron 20X-NDIC / W User manual

Related papers

Other documents