ALFAtron 30X-HDBaseT User manual

ALFAtron
Brand
ALFAtron
Model
30X-HDBaseT
Category
Security cameras
Type
User manual

This manual is also suitable for

ALFATRON
ALF-5X/10X/12X/20X/30X-HDBaseT
Full HD PTZ Camera
ALFATRON ELECTRONICS GmbH GERMANY
User Manual
2
ALFATRON ALF-5/10/12/20X/30X-HDBT
Attention
NOTE: This equipment has been tested and was found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment can generate and radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference through one or more of the following measures:
---Reorient or relocate the receiving antenna.
---Increase the distance between the equipment and receiver.
---Connect the equipment into an outlet on a circuit different from which the receiver is connected.
---Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications not expressly approved by the party responsible for compliance, could void the
user's authority to operate the equipment.
Radiation Exposure
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two
conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.
ALFATRON ALF-5/10/12/20X/30X-HDBT
Electric Safety
Installation and operation must comply in accordance with electric safety standards
Caution during transport
Avoid stress, vibration and soakage in transportation, storage and installation.
The polarity of the power supply
The power supply of the product is ±12V and the maximum electrical current is 2A.
Below is the drawing, indicating the polarity of the power supply.
Careful considerations during installation
Never move the camera by grabbing the camera head directly. Do not rotate the camera head by hand, as
mechanical issues may occur.
This device must be installed on a level desk or platform, and cannot be installed askew.
Do not use any corrosive liquid when cleaning the device as the cover is made up of organic material.
Ensure that there are no obstacles within rotation range.
Never power unit up before installation is completed.
Do not disassemble at your own discretion.
We are not responsible for any unauthorized modification or dismantling.
Attention
An Electromagnetic field under a certain rate may affect the camera image!
4
ALFATRON ALF-5/10/12/20X/30X-HDBT
Context
1. Quick Installation ..................................................................................................................................................... 5
1.1 Camera Interface Explanation ....................................................................................................................... 6
1.2 Power on initial configuration ....................................................................................................................... 6
1.3 Video Output ................................................................................................................................................. 6
2. Product overview ..................................................................................................................................................... 6
2.1 Product Introduction ..................................................................................................................................... 6
2.1.1 Dimension .................................................................................................................................... 6
2.1.2 Accessory ............................................................................................................................................ 6
2.2 Main Features ................................................................................................................................................ 7
2.2.1 Camera Performance .......................................................................................................................... 7
2.2.2 Network performance ........................................................................................................................ 7
2.3 Technical Specification .................................................................................................................................. 8
2.4 Connections ................................................................................................................................................... 9
3. Application Instruction .......................................................................................................................................... 10
3.1 Video Output ............................................................................................................................................... 10
3.1.1 Power-On Initial Configuration ......................................................................................................... 10
3.2 Remote Controller ....................................................................................................................................... 10
3.2.1 Button Instruction ............................................................................................................................................. 10
3.2.2 Applications ...................................................................................................................................... 11
3.3 MENU SETTING ............................................................................................................................................ 12
3.3.1 Main Menu ....................................................................................................................................... 12
3.3.2 System Setting .................................................................................................................................. 13
3.3.3 Camera Setting .................................................................................................................................. 14
3.3.4 P/T/Z ................................................................................................................................................. 16
3.3.5 Video Format .................................................................................................................................... 17
3.3.6 Version .............................................................................................................................................. 17
3.3.7 Restore Default ................................................................................................................................. 18
4. Network Connection ...................................................................................................................................... 18
4.1 Connecting Mode................................................................................................................................. 18
4.2 IE Log In ........................................................................................................................................................ 21
4.2.1 a) Web client ..................................................................................................................................... 21
4.2.1 b) Download/Install Plugin................................................................................................................ 21
4.2.2 Preview ............................................................................................................................................. 21
4.2.3 Configuration .................................................................................................................................... 22
4.2.4 Video configuration .......................................................................................................................... 22
4.2.5 Network configuration ...................................................................................................................... 24
4.2.6 System configuration ........................................................................................................................ 25
4.2.7 Logout ............................................................................................................................................... 26
4.2.9 Wireless network .............................................................................................................................. 26
5. Serial Communication Control ............................................................................................................................... 27
5.1 VISCA protocol list........................................................................................................................................ 27
5.1.1 Camera return command .................................................................................................................. 27
ALFATRON ALF-5/10/12/20X/30X-HDBT
5.1.2 Camera control command ................................................................................................................ 27
5.1.3 ,Inquiry command .............................................................................................................................. 30
5.2 ,Pelco-D protocol command list ................................................................................................................... 32
5.3 Pelco-P protocol command list .................................................................................................................... 32
6. Camera Maintenance and Troubleshooting .......................................................................................................... 33
6.1 Camera Maintenance .................................................................................................................................. 33
6.2 Troubleshooting ........................................................................................................................................... 33
7. Warranty ........................................................................................................................................................ 35
6
ALFATRON ALF-5/10/12/20X/30X-HDBT
1.
Quick Installation
1.1
Camera Interface Explanation
Figure 1.1 Interface of HD BaseT Series
1. Camera Lens 6. RS232 (In)
2. Camera Base 7. Audio in
3. Remote Controller Receiver Light 8. HDBaseT Port
4. DIP Switch 9. LAN Port
5. Tripod Screw Hole 10. Power Supply
1.2
Power on initial configuration
1) Power on: Connect DC12V power supply adapter with the power supply socket.
2) Initial configuration: Power the device on with the remote control, the front panel light will flash red. The camera head then
moves down and rotates left. The camera head then goes to the HOME position, front and centre. When the remote control receiver
light stops blinking and turns green, the self-checking is complete.
Note: If you set preset 0, when Power-on self-test is completed, the camera automatically moves to the preset 0 positions.
1.3
Video Output
HDBaseT video output
a. IP cable connect: HD model pls refer to figure 1.1 No.8 above.
b. Connect the PTZ Camera to the copmpatible Alfatron HDBaseT receiver using a compatible HDBaseT network cable.
4
ALFATRON ALF-5/10/12/20X/30X-HDBT
1.4
Bracket mount
Note: Bracket can only be wall-mounted or mounted upside-down on the concrete wall. Bracket cannot be installed on plasterboard.
1) Wall mount steps
ALFATRON ALF-5/10/12/20X/30X-HDBT
2.
Upside down mounting steps
6
ALFATRON ALF-5/10/12/20X/30X-HDBT
2. Product overview
2.1
Product Introduction
2.1.1
Dimension
Figure 2.2 Camera dimension
2.1.2
Accessory
When unpacking, ensure all the supplied accessories are included:
Model NO.
Configuration
HDBaseT
Accessory
Standard
1 x Power adapter
1 x RS232 cable
1 x User manual
4 x Double-side glue shim
1 x Warranty card
1 x IR Remote controller
Wall or Ceiling Mount Bracket
(The specific bracket required is chosen at purchase)
ALFATRON ALF-5/10/12/20X/30X-HDBT
2.2
Main Features
2.2.1
Camera Performance
The Alfatron ALF-X-HDBaseT series camera offers flawless functionality, superior performance and rich interfaces. The features
include advanced ISP processing algorithms to provide high resolution vivid images with a strong sense of depth and excellent colour
rendition. It supports H.265/H.264 encoding which makes motion video fluent and clear even with less than ideal bandwidth
conditions.
1. Superb High-definition Image: Utilizes 1/2.8-inch-high quality CMOS sensor. Resolution is up to 1920x1080 with a frame rate up
to 60 fps.
2. Various Optical Zoom Lens: It has 5X/10X/12X/20X optical zoom lens for options. The 5X zoom lens has a 80.9 ° wide view
angle without distortion.
3. Leading Auto Focus Technology: Leading auto focus algorithm assures the lens is fast, accurate and stable at auto-focusing.
4.Low Noise and High SNR: Low Noise CMOS effectively ensures high SNR of camera video.
Advanced 2D/3D noise reduction technology is also used to further reduce the noise while ensuring image sharpness.
5.Quiet PTZ: By adopting a high accuracy step driving motor, the camera works quietly and moves smoothly and quickly to a
designated position.
6.Video Outputs: supports HDBaseT.
7.Remote Controls: IR remote controller.
8.Low-power Sleep Function: Supports low-power sleep/wake up. The consumption is lower than 500mW under sleep mode.
9.Support Multiple Control Protocol: Supports VISCA, PELCO-D and PELCO-P protocols which can also be automatically
recognized. Supports VISCA control protocol via the IP port.
10.255 Presets Positions: Up to 255 presets (10 presets via remote Controller).
11.Wide usage Application: Tele-education, Lecture Capture, Webcasting, Videoconferencing, Tele-training, Tele-medicine,
Interrogation and Emergency command systems.
2.2.2
Network performance
1. Audio Input Interface: Supports 16000/ 32000/ 44100/ 48000 Hz sampling frequency and AAC, MP3, PCM audio coding.
2.Multiple Audio/Video Compression: Support H.264/H.265 video compression; AAC,MP3 and PCM audio compression;
Supports compression of resolutions up to 1920x1080 with frame rates up to 60 fps and 2 audio channels.
3.Multiple network protocols: Supports ONVIF, RTSP, RTMP protocols and RTMP push mode, easy to link streaming media server
(Wowza, FMS)
8
ALFATRON ALF-5/10/12/20X/30X-HDBT
2.3
Technical Specification
5X
10X
12X
20X
30X
Camera Parameter
1/2.8-inch-high quality HD CMOS sensor
16: 9 2.07 megapixel
HDBaseT video format
1080P60/50/30/25/59.94/29.97;1080I60/50/59.94;720P60/50/30/25/59.94/29.97
5X
f＝3.6～18mm
10X
f＝4.7～47mm
12X
f ＝ 3.9 ～
46.1mm
20X
f＝5.2～98mm
30X
f＝4.3～129mm
16.43°
（
tele
）
80.9°
（
wide
）
6.43°
（
tele
）
60.9°
（
wide
）
6.3°
（
tele
）
72.5°
（
wide
）
3.3°
（
tele
）
54.7°
（
wide
）
2.34°(tele)--65.1
°(wide)
F1.8 – F2.8
F1.6 – F3.0
F1.8 – F2.4
F1.5 – F3.5
F1.6 ～ F4.7
10X
0.5Lux (F1.8, AGC ON)
2D & 3D DNR
Auto / Manual/ One Push/ 3000K/ 4000K/5000K/6500K
Auto/Manual
Auto/Manual
Auto/Manual
ON/OFF
OFF/ Dynamic level adjustment
Brightness, Color, Saturation, Contrast, Sharpness, B/W mode, Gamma curve
>55dB
Input/Output Interface
HDBaseT(POE), LAN, Audio-in, RS232
Double streams output simultaneously
H.264, H.265
RS-232 Ring through RS232 output, RS-485
VISCA/Pelco-D/Pelco-P; Baud Rate: 115200/9600/4800/2400bps
Double track 3.5mm linear input;
AAC/MP3/PMC Audio compression
100M IP port(100BASE-TX); support IP Visca control protocol
RTSP/RTMP,ONVIF
HEC3800 outlet (DC12V)
PTZ Parameter
Pan Rotation
±170°
Tilt Rotation
-30°
～
+90°
Pan Control Speed
0.1 -60°/sec
Tilt Control Speed
0.1-30°/sec
Preset Speed
Pan: 60°/sec, Tilt: 30°/sec
Preset Number
255 presets (10 presets by the remote controller)
Other Parameter
Supply Adapter
AC110V-AC220V to DC12V/2A
Input Voltage
DC12V±10%
Input Current
1A(Max)
Consumption
12W (Max)
Store Temperature
-10℃ to +60℃
Store Humidity
20% - 95%
Working Temperature
-10℃ to +50℃
Working Humidity
20%--80%
ALFATRON ALF-5/10/12/20X/30X-HDBT
Dimension
150mmX150mmX167.5mm
Weight
1.4KG
Working Environment
Indoor
Remote Operation (IP)
Remote Upgrade, Reboot and Reset
Accessory
Power Supply, RS232 Control Cable, IR Remoter, Manual
Wall or Ceiling Mount Bracket
(The specific bracket required is chosen at purchase)
2.4
Connections
1) The external interface of the HD model: Audio Input, HDBaseT Output, LAN and DC12V Power Interface.
Figure 2.6 HD model external interface diagram
10
ALFATRON ALF-5/10/12/20X/30X-HDBT
3.Application Instruction
3.1
Video Output
3.1.1 Power-On Initial Configuration
Once connecting the power, the camera will initiate the initial configuration, the red indicator light will be flashing. When the camera
returns to the HOME position (middle position for Pan / Tilt) , the lens will zoom in/out and the auto-testing will be completed. IR LED
will also cease flashing. If the preset ‘0’ is set, the camera will rotate to the 0-preset position after initial configuration.
3.2
Remote Controller
3.2.1 Button Instruction
1. Standby Button
After a 3 second long press, the camera will step into standby mode. Long press for 3 seconds again
and the camera will self-test and return to the HOME position. (Note: If the power-on mode is
turned on and Preset 0 is set, and there is no operation within 12 seconds, the camera will
automatically point to the specified preset position.
2. Camera Address Selection
Select the camera address which requires control
3. Number Key
Set or run 0-9 presets
4. *,# Key
Key combination use
5. Focus Control Key
Auto Focus: Enter autofocus mode.
Manual Focus: Enter manual focus mode.
To adjust the camera focus in manual mode press [focus +] or [focus -].
6. Zoom Control Key
Zoom＋: Zoom in
Zoom－: Zoom out
7. Set or Clear Preset key:
To set the preset: Press Set Preset key and 0-9 number key
To clear the preset: Press Clear Preset key and 0-9 number key
8. Pan/Tilt Control Key
Press Key: Up
Press Key: Down
Press Key: Left
Press Key: Right
“HOME” Key: Return to the middle position or enter into the next level menu
9. BLC Control Key
Back Light ON / OFF: Turn on or off the backlight
10. Menu Setting
Open or close the OSD menu
Enter/exit the OSD menu or return to the previous menu.
11. Camera IR Remote Control Address Setting
【*】+【＃】+【F1】: Camera Address No.1
【*】+【＃】+【F2】: Camera Address No. 2
ALFATRON ALF-5/10/12/20X/30X-HDBT
【*】+【＃】+【F3】: Camera Address No. 3
【*】+【＃】+【F4】: Camera Address No. 4
12. Key Combination Functions
1) 【#】+【#】+【#】: Clear all presets
2) 【*】+【#】+【6】: Restore factory defaults
3)
【
*
】
+
【
#
】
+
【
9
】
: Flip switch
4)
【
*
】
+
【
#
】
+Auto : Enter into the ageing mode
5)
【
*
】
+
【
#
】
+
【
3
】
: Menu set to Chinese
6)
【
*
】
+
【
#
】
+
【
4
】
: Menu set to English
7)
【
*
】
+
【
#
】
+Manual: Restore the default user name, password,
and IP address
8)
【
#
】
+
【
#
】
+
【
0
】
: Switch the video format to 1080P60
9)
【
#
】
+
【
#
】
+
【
1
】
: Switch the video format to 1080P50
10)
【
#
】
+
【
#
】
+
【
2
】
: Switch the video format to 1080I60
11)
【
#
】
+
【
#
】
+
【
3
】
: Switch the video format to 1080I50
12)
【
#
】
+
【
#
】
+
【
4
】
: Switch the video format to 720P60
13)
【
#
】
+
【
#
】
+
【
5
】
: Switch the video format to 720P50
14)
【
#
】
+
【
#
】
+
【
6
】
: Switch the video format to 1080P30
15)【#】+【#】+【7】: Switch the video format to 1080P25
16)【#】+【#】+【8】: Switch the video format to 720P30
17)【#】+【#】+【9】: Switch the video format to 720P25
3.2.2
Applications
After completing initialization, the camera can receive and execute the IR commands. Press the remote controller button and the
indicator light will flash; release the button, the indicator light will stop flashing. Users can control the pan/tilt/zoom, setting and
running preset positions via the IR remote controller.
Button Instruction:
1. In this example, “press the button” means a ‘click’ rather than a long-press, and a special note will be given if a long-press for
more than one second is required.
2. When a button-combination is required, do it in sequence. For example,“ 【 *】+【#】+【F1】” means press“【*】” first and
then press“【#】” and lastly press“【F1】”.
1) Camera Selection
Select the camera address to control.
2) Pan/Tilt Control
Up: press Down press
Left: press Right: press
Back to middle position: press“【HOME】”
Press and hold the up/down/left/right button; the pan/tilt will
keep running, from slow to fast, until it runs to the endpoint. The
pan/tilt movement stops as soon as the button is released.
3) Zoom Control
ZOOM IN: press “ZOOM “ key
ZOOM OUT: press “ZOOM ” key
Press and hold the button, the camera will keep zooming in or
zooming out and stops as soon as the button is released.
4) Focus Control
12
ALFATRON ALF-5/10/12/20X/30X-HDBT
Focus (near): Press
【
“ focus+
】
” button (Valid only in manual focus
mode)
Focus (far): Press “【focus-】” button (Valid only in manual focus
mode)
Auto Focus: Supported
Manual Focus: Supported
Press and hold the button, the focus action will continue and will
stop as soon as the button is released.
5) BLC Setting
BLC ON / OFF: supported
6) Presets Setting, Running, Clearing
1. Preset setting: To set a preset position, the user should press
the “【SET PRESET】” button first and then press a numbered
button between 0 and 9 to set the relative preset.
Note: 10 preset positions in total are available via the remote
controller.
2. Preset Running: Press a numbered button between 0 and 9 to
run a relative preset.
3. Preset clearing: To clear a preset position, the user can press
the “【CLEAR PRESET】” button first and then press the numbered
button between 0 and 9 to clear the relative preset.
Note: pressing the“
【
#
】
” button three times consecutively to
cancel all the presets.
7) Camera Remote Controller Address Setting
【*】+【＃】+【F1】: Camera Address No.1
【*】+【＃】+【F2】: Camera Address No. 2
【*】+【＃】+【F3】: Camera Address No. 3
【*】+【＃】+【F4】: Camera Address No. 4
3.3
MENU SETTING
3.3.1
Main Menu
In normal working mode, press the【MENU】button to display the menu. Use the arrow buttons to highlight the menus items.
ALFATRON ALF-5/10/12/20X/30X-HDBT
LANGUAGE: Language setting, Chinese / English
SETUP: System setting
CAMERA OPTION: Camera setting
PTZ OPTION: Pan / Tilt setting
VERSION: Camera version setting
Restore Default: Reset setting
[↑↓] Select: For selecting within the menu
[← →] Change Value: For modifying parameters
[MENU] Back: Press [MENU] to return
[Home] OK: Press [Home] to confirm
3.3.2
System Setting
Move the pointer to the (Setup) within the Main Menu, click the【HOME】button and enter into the (System Setting) as shown
below:
PROTOCOL: VISCA/Pelco-P/Pelco-D/Auto
Visca address: 1~7
Visca Address Fix: On/Off
Pelco-P address: 1~255
Pelco-D address: 1~255
Baud rate: 2400/4800/9600/115200
MENU
＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝
Language
English
(Setup)
(Camera)
(P/T/Z)
(Video
Format)
(Version)
(Restore Default)
[ ↑↓ ]Select
Value
[ ← → ]Change
SETUP
＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝
Protocol Auto
Visca Address 1
Visca Address Fix OFF
PELCO-P Address 1
PELCO-D Address 0
Baudrate 9600
[↑↓]Select
Value
[← →]Change
14
ALFATRON ALF-5/10/12/20X/30X-HDBT
CAMERA
＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝
(Exposure)
(Color)
(Image)
(Focus)
(Noise Reduction)
[↑↓]Select
Value
[← →]Change
EXPOSURE
＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝
Mode Auto
EV OFF
BLC OFF
Anti-Flicker 50Hz
Gain Limit 3
WDR 5
[
↑↓
]Select [
← →
]Change
Value
3.3.3
Camera Setting
Move the pointer to the (CAMERA) in the Main Menu, click the【HOME】button and enter the (CAMERA) as follows:
Exposure: Enter the Exposure settings
Color: Enter the the colour settings
Image: Enter the image settings
Focus: Enter the focus settings
Noise Reduction: Enter the noise reduction settings
1) EXPOSURE SETTING
Move the pointer to the (EXPOSURE) within the Main Menu, click the【HOME】button and enter the (EXPOSURE SET) as follows:
Mode: Auto, Manual, Shutter priority, Iris priority and Brightness priority.
EV : On / Off (only available in auto mode)
Compensation Level: -7~7 (only available in auto mode when EV is ON)
BLC: On / Off options (only available in auto mode)
Anti-Flicker: OFF / 50Hz / 60Hz options ( only available in Auto / Iris priority / Brightness priority modes)
Gain Limit: 0~15 ( only available in Auto / Iris priority / Brightness priority mode)
WDR: Off,1~8
Shutter priority:1/25, 1/30, 1/50, 1/60, 1/90, 1/100, 1/120, 1/180, 1/250, 1/350, 1/500, 1/1000, 1/2000, 1/3000, 1/4000, 1/6000,
ALFATRON ALF-5/10/12/20X/30X-HDBT
COLOR
＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝
WB Mode Auto
Saturation 80%
Hue 7
AWB Sensitivity High
Color style Default
Color temp Low
[ ↑↓ ]Select
Value
[ ← → ]Change
IMAGE
＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝
Brightness 6
Contrast 8
Sharpness 7
Flip-H OFF
Flip-V OFF
B&W-Mode Color
Gamma Default
DZoom OFF
DCI Close
[
↑↓
]Select [
← →
]Change
Value
1/10000 (only available in Manual and Shutter priority mode)
IRIS Priority:OFF, F11.0, F9.6, F8.0, F6.8, F5.6, F4.8, F4.0, F3.4, F2.8, F2.4, F2.0, F1.8 (only available in Manual and Iris priority mode)
Brightness: 0~23 (only available in Brightness priority mode)
2) COLOR SETTING
Move the pointer to the (COLOR) within the Main Menu, click the【HOME】button and enter the (COLOR SET) as follows:
WB Mode: Auto, 3000K, 3500K, 4000K, 4500K, 5000K, 5500K, 6000K, 6500K, 7000K, Manual, One Push
Red Gain: 0~255 (only available in Manual mode)
Blue Gain: 0~255 (only available in Manual mode)
Saturation: 60%, 70%, 80%, 90%, 100%, 110%, 120%, 130%
Hue: 0~14
AWB Sensitivity: high / middle / low
Color Style: Default, style1~4.
Color Temp: high / middle / low
3) IMAGE
Move the pointer to the (IMAGE) within the Menu, click the【HOME】button and enter the (IMAGE) as follows:
Brightness: 0~14
16
ALFATRON ALF-5/10/12/20X/30X-HDBT
FOCUS
＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝
Focus Mode Auto
AF-Zone Center
AF-Sensitivity Low
[↑↓]Select
Value
[← →]Change
Contrast: 0~14
Sharpness: 0~15
Flip-H: On/Off
Flip-V: On/Off
B&W Mode: Color, black / white
Gamma: Default, 0.47, 0.50, 0.52, 0.55
DZoom: digital zoom options: On/Off
DCI: Dynamic Contrast: Off,1～8
4) FOCUS
Move the pointer to the (FOCUS) within the Menu, click the【HOME】button and enter the (FOCUS) as follows:
Focus Mode: Auto, manual
AF-Zone: Up, middle, down
AF-Sensitivity: High, middle, low
5) NOISE REDUCTION
Move the pointer to the (NOISE REDUCTION) within the Menu, click the【HOME】 button and enter the (NOISE REDUCTION) as
follows:
2D Noise Reduction: Auto, close, 1~7
3D Noise Reduction: Close, 1~8
Dynamic Hot Pixel: Close, 1~5
3.3.4
P/T/Z
Move the pointer to the (P/T/Z) within the Main Menu, click the【HOME】button and enter the (P/T/Z) as follows:
NOISE REDUCTION
＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝
NR-2D Auto
NR-3D 3
Dynamic Hot Pixel OFF
[↑↓]Select
Value
[← →]Change
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40

ALFAtron 30X-HDBaseT User manual

ALFAtron
Brand
ALFAtron
Model
30X-HDBaseT
Category
Security cameras
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents