Aruba JH103A Installation guide

HPE FlexFabric 12900E Switch Series

Installation Guide

P

art number: 5200-8060

Document version: 6W109-20210707

i

The information contained herein is subject to change without notice. The only warranties for Hewlett Packard

Enterprise products and services are set forth in the express warranty statements accompanying such

products and services. Nothing herein should be construed as constituting an additional warranty. Hewlett

Packard Enterprise shall not be liable for technical or editorial errors or omissions contained herein.

Confidential computer software. Valid license from Hewlett Packard Enterprise required for possession, use, or

copying. Consistent with FAR 12.211 and 12.212, Commercial Computer Software, Computer Software

Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under vendor’s

standard commercial license.

Links to third-party websites take you outside the Hewlett Packard Enterprise website. Hewlett Packard

Enterprise has no control over and is not responsible for information outside the Hewlett Packard Enterprise

website.

Acknowledgments

Intel®, Itanium®, Pentium®, Intel Inside®, and the Intel Inside logo are trademarks of Intel Corporation in the

United States and other countries.

Microsoft® and Windows® are trademarks of the Microsoft group of companies.

Adobe® and Acrobat® are trademarks of Adobe Systems Incorporated.

Java and Oracle are registered trademarks of Oracle and/or its affiliates.

UNIX® is a registered trademark of The Open Group.

i

Contents

Preparing for installation ················································································ 1

Safety recommendations ··································································································································· 1

General safety recommendations ·············································································································· 1

Electricity safety ········································································································································· 1

Handling safety ·········································································································································· 2

ESD prevention ·········································································································································· 2

Laser safety ················································································································································ 2

Examining the installation site ···························································································································· 2

Weight support ··········································································································································· 2

Temperature ··············································································································································· 3

Humidity ····················································································································································· 3

Cleanliness ················································································································································· 3

EMI ····························································································································································· 4

Grounding ·················································································································································· 4

Power ························································································································································· 4

Cooling ······················································································································································· 4

Space ························································································································································· 5

Installation accessories ······································································································································ 7

Installing the switch ······················································································ 14

Confirming installation preparations ················································································································· 14

Installing the switch in a rack ··························································································································· 15

Switch dimensions and rack requirements ······························································································· 15

Attaching mounting brackets and chassis rails to the switch ··································································· 19

Attaching slide rails to the rack ················································································································ 20

Installing cage nuts for attaching mounting brackets ··············································································· 28

Mounting the switch in a rack ··················································································································· 31

Grounding the switch ······································································································································· 35

Grounding the switch by using a grounding strip ····················································································· 35

Installing FRUs ···························································································· 37

Attaching an ESD wrist strap ··························································································································· 37

Installing MPUs ················································································································································ 39

Installing MPUs for the 12916E and 12908E switches ············································································ 39

Installing MPUs for a 12904E switch········································································································ 40

Installing MPUs for a 12902E switch········································································································ 41

Installing LPUs ················································································································································· 42

Installing 12900 LPUs ······························································································································ 43

Installing 12900E LPUs ···························································································································· 46

Installing an LPU with foldable ejector levers··························································································· 48

Installing cable management brackets ············································································································· 50

Installing switching fabric modules ··················································································································· 50

Installing a filler panel in a switching fabric module slot ··········································································· 52

Removing a filler panel from a switching fabric module slot ···································································· 53

Installing fan trays ············································································································································ 54

Installing fan trays for the 12916E and 12908E switches ········································································ 55

Installing fan trays for a 12904E switch···································································································· 56

Installing fan trays for a 12902E switch···································································································· 56

Installing fan trays for a 12901E switch···································································································· 58

Installing power supplies ·································································································································· 58

Connecting the power cord ······························································································································ 60

(Optional.) Installing transceiver modules ········································································································ 61

Installing an SFP+/SFP/QSFP+/QSFP28 module ··················································································· 61

Installing a CFP2 module ························································································································· 62

Installing a CXP module ··························································································································· 63

Connecting a CXP fiber cable ·················································································································· 64

Connecting an SFP+/QSFP+/QSFP28/QSFP+ to SFP+ copper cable···················································· 64

ii

Setting up an IRF fabric ··············································································· 66

IRF fabric setup flowchart ································································································································ 66

Planning IRF fabric setup ································································································································· 67

Planning IRF fabric size and the installation site ······················································································ 67

Identifying the master switch and planning IRF member IDs ··································································· 67

Planning IRF topology and connections··································································································· 68

Identifying physical IRF ports on the member switches ··········································································· 68

Installing IRF member switches ······················································································································· 68

Configuring basic IRF settings ························································································································· 68

Connecting the physical IRF ports ··················································································································· 69

Verifying the IRF fabric configuration ··············································································································· 69

Connecting your switch to the network ························································ 71

Accessing the switch for the first time ·············································································································· 71

Setting up the configuration environment································································································· 71

Setting terminal parameters ····················································································································· 72

Powering on the switch ···························································································································· 72

Configuring the switch ······································································································································ 74

Configuring authentication on a user interface························································································· 74

Configuring the basic access function ······································································································ 74

Configuration example ····························································································································· 75

Verifying the network configuration ·········································································································· 76

Connecting the switch to the network ·············································································································· 76

Connecting the switch to the network by using Ethernet twisted pair cables ··········································· 76

Connecting the switch to the network through an optical fiber ································································· 76

Testing connectivity·········································································································································· 77

Troubleshooting ··························································································· 78

Troubleshooting methods································································································································· 78

System failures at startup································································································································· 78

No display on the configuration terminal ·································································································· 78

Garbled display on the configuration terminal ·························································································· 79

System failures during operation ····················································································································· 79

Power supply failure ········································································································································· 79

Fan tray failure ················································································································································· 80

MPU failure ······················································································································································ 81

LPU failure ······················································································································································· 81

Switching fabric module failure ························································································································ 82

Interface failure ················································································································································ 83

Technical support ············································································································································· 84

Replacement procedures ············································································· 85

Replacing a power supply ································································································································ 85

Replacing a card ·············································································································································· 86

Replacing an MPU/LPU ··························································································································· 86

(Optional) Removing an interface module adapter ·················································································· 89

Removing an LPU protective blank panel ································································································ 90

Replacing a switching fabric module ········································································································ 90

Replacing a fan tray ········································································································································· 92

Replacing a transceiver module ······················································································································· 94

Replacing a CFP2 module ······················································································································· 94

Replacing an SFP+/SFP/QSFP+/QSFP28 module·················································································· 94

Replacing a CXP module ························································································································· 94

Replacing a CXP fiber cable ···················································································································· 95

Replacing an SFP+/QSFP+/QSFP+ to SFP+ copper cable ····································································· 95

Appendix A Chassis views and technical specifications ······························· 96

Chassis views ·················································································································································· 96

Weights and dimensions ·································································································································· 98

Module power consumption and system power consumption ······································································· 101

Card power consumption ······················································································································· 101

iii

Fan tray power consumption ·················································································································· 102

System power consumption ··················································································································· 103

Heat dissipation·············································································································································· 103

Environmental specifications·························································································································· 103

Noise ······························································································································································ 104

Appendix B FRUs and compatibility matrixes ············································ 105

MPUs ····························································································································································· 105

Interface module adapter ······························································································································· 108

LPUs ······························································································································································ 108

12900 LPUs ··········································································································································· 108

12900E LPUs ········································································································································· 110

Sub modules for LSXM1TGS24QGMODHB1 ································································································ 113

Sub modules for LSXM1TGS24CGMODHD1 ································································································ 114

Switching fabric modules ······························································································································· 114

Power supplies ··············································································································································· 115

Fan trays ························································································································································ 118

Mounting accessories ···································································································································· 118

Transceiver modules ······································································································································ 119

DC power cords ············································································································································· 124

AC power cords·············································································································································· 124

Appendix C LEDs ······················································································ 127

MPU LEDs ····················································································································································· 127

Management Ethernet port LEDs··········································································································· 128

Fan tray status LEDs ······························································································································ 128

Power supply status LEDs ····················································································································· 128

Card status LEDs ··································································································································· 129

MPU active/standby status LED ············································································································· 129

LPU LEDs ······················································································································································ 130

RJ-45 Ethernet port LEDs ······················································································································ 130

SFP port LEDs ······································································································································· 130

SFP+ port LEDs ····································································································································· 130

QSFP+ port LEDs ·································································································································· 130

QSFP28 port LEDs ································································································································ 131

CXP port LEDs ······································································································································· 131

CFP2 port LEDs ····································································································································· 131

Switching fabric module status LEDs ············································································································· 132

Switching fabric module status LED on a switching fabric module ························································ 132

Switching fabric module status LEDs on a fan tray ················································································ 132

Fan tray status LEDs······································································································································ 133

Power supply LEDs ········································································································································ 134

Appendix D Cables ···················································································· 136

Console cable ················································································································································ 136

Ethernet twisted pair cable ····························································································································· 137

RJ-45 connector ····································································································································· 137

Cable pinouts ········································································································································· 137

Cable type ·············································································································································· 137

Pin assignments ····································································································································· 139

Making an Ethernet twisted pair cable ··································································································· 140

Optical fiber ···················································································································································· 140

Optical fiber ············································································································································ 140

Optical fiber cable ·································································································································· 141

Patch cord ·············································································································································· 141

Pigtail cord ············································································································································· 141

Fiber connector ······································································································································ 141

Precautions ············································································································································ 142

SFP+ copper cable ········································································································································ 142

QSFP+ copper cable ······································································································································ 143

QSFP28 copper cable ···································································································································· 143

QSFP+ to SFP+ copper cable························································································································ 143

iv

CXP fiber cable ·············································································································································· 144

Appendix E Engineering labels ·································································· 145

Labels for cables ············································································································································ 145

Labels for network cables ······················································································································ 145

Labels for power cords ··························································································································· 145

Generic labels ········································································································································ 146

Labels for devices ·········································································································································· 147

Filling in labels················································································································································ 147

Affixing labels ················································································································································· 147

Affixing a label to a network cable ·········································································································· 147

Affixing a label to a power cord ·············································································································· 148

Affixing a generic label ··························································································································· 149

Affixing a label to a device ····················································································································· 150

Guidelines ······················································································································································ 150

Examples ······················································································································································· 150

Engineering labels for twisted-pair cables ······························································································ 150

Engineering labels for optical fibers ······································································································· 151

Engineering labels for AC power cords ·································································································· 153

Engineering labels for DC power cords ·································································································· 154

Engineering labels for devices ··············································································································· 155

Appendix F Cabling recommendations ······················································ 157

Routing signal cables ····································································································································· 157

Routing power cords ······································································································································ 157

General cabling requirements ························································································································ 158

Prerequisites ·················································································································································· 159

Cable management guidelines ······················································································································ 159

Appendix G Repacking the switch ····························································· 162

Removing cables from the switch ·················································································································· 162

Removing the power cords ···················································································································· 162

Removing the console cable ·················································································································· 162

Removing the grounding cable ·············································································································· 162

Removing the twisted pair cables and optical fibers ·············································································· 163

Repacking the FRUs ······································································································································ 163

Repacking power supplies ····················································································································· 163

Repacking the cards ······························································································································ 164

Repacking the interface module adapters······························································································ 164

Repacking the switching fabric module slot filler panels ········································································ 164

Repacking the switch chassis ························································································································ 165

Removing the chassis from the rack ······································································································ 165

Repacking the switch chassis ················································································································ 166

Document conventions and icons ······························································ 169

Conventions ··················································································································································· 169

Network topology icons ·································································································································· 170

Support and other resources ····································································· 171

Accessing Hewlett Packard Enterprise Support····························································································· 171

Accessing updates ········································································································································· 171

Websites ················································································································································ 171

Customer self repair ······························································································································· 172

Remote support ······································································································································ 172

Documentation feedback ······················································································································· 172

Index ·········································································································· 173

1

Preparing for installation

HPE FlexFabric 12900E Switch Series includes the models in Table 1.

Table 1 HPE FlexFabric 12900E Switch Series models

Product code

(J number)

HPE description Alias RMN

JH103A HPE FlexFabric 12916E Switch Chassis 12916E BJNGA-AC0014

JH255A HPE FlexFabric 12908E Switch Chassis 12908E BJNGA-AC0015

JH262A HPE FlexFabric 12904E Switch Chassis 12904E BJNGA-AC0016

JH345A HPE FlexFabric 12902E Switch Chassis 12902E BJNGA-AC0018

JH951A HPE FlexFabric 12901E Switch Chassis 12901E BJNGA-AC0020

IMPORTANT:

For regulatory identification purposes,

HPE 12900E switches are assigned regulatory model

numbers (RMN). The regulatory number should not be confused with the marketing name

HPE

129XXE or the product code.

For model, product code (J number), and HPE description of MPUs, switching fabric modules, LPUs,

LPU adapter, power supplies, and fan trays, see "Appendix B FRUs and compatibility matrixes."

Safety recommendations

To avoid possible bodily injury and equipment damage, read Compliance and Safety Manual

provided with the switch and all safety recommendations in this chapter carefully before installation.

The recommendations do not cover every possible hazardous condition.

General safety recommendations

•

Keep the switch clean and dust-free.

•

Do not place the switch on a moist area, and avoid liquid flowing into the switch.

•

Make sure the ground is dry and flat and anti-slip measures are in place.

•

Keep the switch and installation tools away from walk areas.

•

Do not wear loose clothing, jewelry (for example, necklace) or any other things that could get

caught in the switch when you install and maintain the switch.

Electricity safety

•

Clear the work area of possible electricity hazards, such as ungrounded power extension

cables, missing safety grounds, and wet floors.

•

Locate the emergency power-off switch in the room before installation so you can quickly shut

power off when an electrical accident occurs.

•

Remove all external cables, including power cords, before moving the chassis.

•

Do not work alone when the switch has power.

•

Before performing a task that is hazardous when power is present, make sure the switch is

completely powered off.

2

Handling safety

CAUTION:

Do not hold the handle of

a fan tray, a power supply, or a card, or the air vents of the chassis to

move the switch

. Any attempt to move the switch with these parts might cause equi

pment damage

and even bodily injury.

Remove power supplies, cards, and all external cables, including the power cords, before moving

the chassis. As a best practice, use a mechanical lift, such as forklift truck, to move the chassis.

If no mechanical lift is used, follow these guidelines to move the chassis:

•

Cooperate with a minimum of four people to move the chassis.

•

Lift the chassis by using the chassis handles or by supporting the bottom from the two sides.

•

Lift and put down the chassis slowly and never move suddenly.

ESD prevention

To prevent the electric component from being damaged by electrostatic discharge (ESD), follow

these guidelines:

•

Ground the switch reliably. For how to ground your switch, see "Installing the switch."

•

Always wear an ESD wrist strap and make sure it is reliably grounded when installing FRUs.

For how to use an ESD wrist strap, see "Installing FRUs."

•

Hold a PCB by its edges. Do not touch any electronic components or printed circuit.

•

Put cards away in antistatic bags for future use.

Laser safety

WARNING

!

Do not stare into any

fiber port or view directly with non-attenuating optical instruments when the

switch has power. The laser light emitted from the fiber port might hurt your eyes.

The switch is a Class 1 laser product.

Examining the installation site

The switch must be used indoors. To ensure correct operation and long lifespan of your switch, the

installation site must meet the requirements in this section.

Weight support

Make sure the floor can support the total weight of the rack, chassis, cards, power supplies, and all

other components. To mount the switch in a rack, make sure the slide rails can support the total

weight of the switch and its accessories (cards, power supplies, and transceiver modules).

Additionally, the floor and slide rail loading plan must also consider system expansion, such as

adding more cards. For more information, see "Appendix A Chassis views and technical

specifications."

3

Temperature

CAUTION:

If condensation appears on the chassis when you move it to a high

-temperature environment, dry

the chassis before powering it on to avoid short circuits.

To ensure correct operation of the switch, make sure the room temperature meets the requirements

in Table 2.

Table 2 Temperature requirements

Temperature

Range

Operating temperature 0°C to 40°C (32°F to 104°F)

Storage temperature –40°C to +70°C (–40°F to +158°F)

Humidity

Maintain appropriate humidity in your equipment room, as described in Table 3.

•

Lasting high relative humidity can cause poor insulation, electricity leakage, mechanical

property change of materials, and metal corrosion.

•

Lasting low relative humidity can cause washer contraction and ESD and cause problems

including loose mounting screws and circuit failure.

Table 3 Humidity requirements

Humidity

Range

Operating humidity 5% to 95%, noncondensing

Storage humidity 5% to 95%, noncondensing

Cleanliness

Dust buildup on the chassis might result in electrostatic adsorption, which causes poor contact of

metal components and contact points. In the worst case, electrostatic adsorption can cause

communication failure.

Table 4 Dust concentration limit in the equipment room

Substance

Concentration limit (particles/m

3

)

Dust particles ≤ 3 x 104

(No visible dust on desk in three days)

NOTE:

Dust particle diameter ≥ 5 µm

The equipment room must also meet limits on salts, acids, and sulfides to eliminate corrosion and

premature aging of components, as shown in Table 5.

Table 5 Harmful gas limits in the equipment room

Gas

Max. (mg/m

3

)

SO2 0.2

4

Gas

Max. (mg/m

3

)

H2S 0.006

NH3 0.05

Cl2 0.01

EMI

All electromagnetic interference (EMI) sources, from outside or inside of the switch and application

system, adversely affect the switch in the following ways:

•

A conduction pattern of capacitance coupling.

•

Inductance coupling.

•

Electromagnetic wave radiation.

•

Common impedance (including the grounding system) coupling.

To prevent EMI, use the following guidelines:

•

If AC power is used, use a single-phase three-wire power receptacle with protection earth (PE)

to filter interference from the power grid.

•

Keep the switch far away from radio transmitting stations, radar stations, and high-frequency

devices.

•

Use electromagnetic shielding, for example, shielded interface cables, when necessary.

Grounding

Using a good grounding system to protect your switch against lightning shocks, interferences, and

ESD is essential to the operating reliability of your switch.

Make sure the equipment room grounding system has a resistance value less than 1 ohm.

For more information about grounding the switch, see "Installing the switch."

Power

Perform the following tasks to meet the power requirements:

1. Calculate the system power consumption.

The system power consumption varies by card type and density. For more information about

system power consumption calculation, see "Appendix A Chassis views and technical

specifications."

2. Identify the number of power supplies.

The total maximum output power of all power supplies must be higher than the system power

consumption. For more information about available power supplies, see "Appendix B FRUs and

compatibility matrixes."

3. Verify that the power system at the installation site meets the requirements of the power

supplies, including the input method and rated input voltage. For more information about power

supply specifications, see "Appendix B FRUs and compatibility matrixes."

Cooling

Plan the installation site for adequate ventilation:

•

Leave a minimum of 30 cm (11.81 in) of clearance at the inlet and outlet air vents.

5

•

The rack for the switch has a good cooling system.

•

The installation site has a good cooling system.

•

Verify that the airflow design of the chassis meets the airflow design of the installation site.

Figure 1 Airflow through the switch (12916E switch)

(1) Chassis air intake direction

(2) Chassis air exhaust direction

Space

For easy installation and maintenance, follow these space requirements:

•

Reserve a minimum of 1.2 m (3.94 ft) of clearance between the rack and walls or other devices.

•

Make sure the rack has enough space to accommodate the switch. See Table 6 for rack

requirements.

For more information about chassis dimensions, see "Appendix A Chassis views and technical

specifications."

1

2

1

2

1

6

Table 6 Switch dimensions and rack requirements

Model

Chassis dimensions

Rack requirements

12916E

• Height—931 mm (36.65 in)/21 RU

• Width—440 mm (17.32 in)

• Depth—977 mm (38.46 in)

 857 mm (33.74 in) for the chassis

 102 mm (4.02 in) from the rear side

of the mounting bracket front ear to

the management bracket front end

 30 mm (1.18 in) for the fan tray

handle at the rear of the chassis

• A minimum of 1.1 m (3.61 ft) in

depth (recommended)

• A minimum of 130 mm (5.12 in)

between the front rack post

and the front door.

• A minimum of 950 mm (37.40

in) between the front rack post

and the rear door.

12908E

• Height—531 mm (20.91 in)/12 RU

• Width—440 mm (17.32 in)

• Depth—977 mm (38.46 in)

 857 mm (33.74 in) for the chassis

 102 mm (4.02 in) from the rear side

of the mounting bracket front ear to

the management bracket front end

 30 mm (1.18 in) for the fan tray

handle at the rear of the chassis

• A minimum of 1.1 m (3.61 ft) in

depth (recommended)

• A minimum of 130 mm (5.12 in)

between the front rack post

and the front door.

• A minimum of 950 mm (37.40

in) between the front rack post

and the rear door.

12904E

• Height—264 mm (10.39 in)/6 RU

• Width—440 mm (17.32 in)

• Depth—977 mm (38.46 in) when the

LSXM104XFAN (JH265A) fan trays are

installed:

 857 mm (33.74 in) for the chassis

 102 mm (4.02 in) from the rear side

of the mounting bracket front ear to

the management bracket front end

 30 mm (1.18 in) for the fan tray

handle at the rear of the chassis

• Depth—1016 mm (40 in) when the

LSXM104XFANH (JH448A) fan trays are

installed:

 857 mm (33.74 in) for the chassis

 102 mm (4.02 in) from the rear side

of the mounting bracket front ear to

the management bracket front end

 69 mm (2.72 in) for the fan tray

handle at the rear of the chassis

• A minimum of 1.1 m (3.61 ft) in

depth (recommended)

• A minimum of 130 mm (5.12 in)

between the front rack post

and the front door.

• A minimum of 950 mm (37.40

in) between the front rack post

and the rear door.

12902E

• Height—133 mm (5.24 in)/3 RU

• Width—440 mm (17.32 in)

• Depth—1015 mm (39.96 in)

 895 mm (35.24 in) for the chassis

 102 mm (4.02 in) from the rear side

of the mounting bracket front ear to

the management bracket front end

 30 mm (1.18 in) for the fan tray

handle at the rear of the chassis

• A minimum of 1.1 m (3.61 ft) in

depth (recommended)

• A minimum of 130 mm (5.12 in)

between the front rack post

and the front door.

• A minimum of 950 mm (37.40

in) between the front rack post

and the rear door.

7

Model

Chassis dimensions

Rack requirements

12901E

• Height—88.1 mm (3.47 in)/2 RU

• Width—440 mm (17.32 in)

• Depth—975.6 mm (38.41 in)

 856 mm (33.70 in) for the chassis

 92 mm (3.62 in) from the rear side of

the mounting bracket front ear to the

management bracket front end

 27.6 mm (1.09 in) for the power

supply latch at the chassis rear

• A minimum of 1.1 m (3.61 ft) in

depth (recommended)

• A minimum of 130 mm (5.12 in)

between the front rack post

and the front door.

• A minimum of 950 mm (37.40

in) between the front rack post

and the rear door.

Installation accessories

If your installation accessories are damaged or lost, order new ones by using the part number or J

number listed in Table 7.

Table 7 Installation accessories

Product

code

Description Quantity Applicable

models

5188-9604

12916E mounting bracket kit

1 kit 12916E switch

8

Product

code

Description Quantity Applicable

models

5080-0011

12908E mounting bracket kit

1 kit 12908E switch

5003-2136

• 12916E MPU filler panel

• 12908E MPU filler panel

As required

• 12916E

switch

• 12908E

switch

5003-2134

12916E switching fabric module filler panel

As required 12916E switch

9

Product

code

Description Quantity Applicable

models

5003-2407

12908E switching fabric module filler panel

As required 12908E switch

5003-2135

12900E LPU filler panel

As required All 12900E

switches

5066-4433

12900E cable management bracket

As required All 12900E

switches

5188-9607

• 12916E L-type bracket kit

• 12908E L-type bracket kit

1 kit

• 12916E

switch

• 12908E

switch

5190-0785

12904E mounting bracket kit

1 kit 12904E switch

5003-2408

12904E MPU filler panel

As required 12904E switch

10

Product

code

Description Quantity Applicable

models

5003-2409

12904E switching fabric module filler panel

As required 12904E switch

5003-1675

12904E L-type bracket kit

1 kit 12904E switch

JQ059A

HPE FlexFabric 12900E Chassis Universal Rack

Mount Kit

1 kit

• 12916E

switch

• 12908E

switch

JC665A

HPE X421 Chassis Universal 4-post Rackmount

Kit

1 kit 12908E switch

JH042A

HPE FlexFabric 7910 Bottom-Support Rails

1 kit

• 12904E

switch

• 12902E

switch

• 5185-89

66

• 5185-89

65

M6 screw and floating nut

• 12916E—3

0 kits

• 12908E—1

4 kits

• 12904E—8

kits

• 12902E—4

kits

• 12901E—6

kits

All 12900E

switches

11

Product

code

Description Quantity Applicable

models

5003-2137

Power supply filler panel

As required All 12900E

switches

5000-0064

12902E MPU filler panel

1 kit 12902E switch

5000-0065

Power supply filler panel

As required All 12900E

switches

5000-0066

12902E fan tray filler panel

1 kit 12902E switch

5000-0067

12902E LPU protective blank panel

1 kit 12902E switch

5000-0068

12902E mounting bracket kit

1 kit 12902E switch

12

Product

code

Description Quantity Applicable

models

5189-7975

12901E mounting bracket and cable management

bracket kit

1 kit 12901E switch

5185-8684

12901E rack mounting rail kit

1 kit 12901E switch

• JG390A

(3 m,

9.84 ft)

• JG391A

(15 m,

49.21 ft)

• HPE FlexNetwork 10500 48V 3m DC Power

Supply Cable

• HPE FlexNetwork 10500 48V 15m DC Power

Supply Cable

The power cord color code scheme is for illustration

only. The cable delivered for your country or region

might use a different color scheme.

As required

HPE FlexFabric

12900E 2400W

DC Power

Supply Unit

JQ058A(15 m

49.21 ft)

HPE FlexFabric 12902E 48V 15m DC Power

Supply Unit Cable

The power cord color code scheme is for illustration

only. The cable delivered for your country or region

might use a different color scheme.

As required

HPE FlexFabric

12900E 1800W

DC Power

Supply Unit

5185-8748

Power supply removable cable tie

As required All 12900E AC

power supplies

5189-9440

Power supply self-adhesive cable tie

As required All 12900E AC

power supplies

5188-9599

Grounding cable

1 All 12900E

switches

13

Product

code

Description Quantity Applicable

models

5185-8765

ESD wrist strap

1 All 12900E

switches

5185-8627

Console cable

1 All 12900E

switches

5185-8722

SFP/SFP+ dust plug

As required

All 12900E

SFP/SFP+ fiber

Ethernet

interface cards

5187-9022

QSFP+ dust plug

As required

All 12900E

QSFP+ fiber

Ethernet

interface cards

5190-0772

CFP2 dust plug

NOTE:

The figure will be provided later.

As required

All 12900E

CFP2 fiber

Ethernet

interface cards

5189-8397

CXP dust plug

NOTE:

The figure will be provided later.

As required

All 12900E CXP

fiber Ethernet

interface cards

• 5187-91

51 (100

mm, 3.93

in)

• 5185-96

20 (300

mm, 1.81

in)

Removable cable tie

As required All 12900E

switches

14

Installing the switch

IMPORTANT:

Keep the packages of the switch and the components for future use.

Confirming installation preparations

Before you install the switch, verify that:

•

You have read "Preparing for installation" carefully and the installation site meets all the

requirements.

•

A 19-inch rack is ready for use and the rack has enough space to accommodate the switch.

For information about how to install a rack, see the rack installation guide.

•

The rack is sturdy and reliably grounded.

•

No debris exists inside or around the rack.

•

The heaviest device is placed at the bottom of the rack.

•

The rack power supplying capabilities meet the device requirements. For information about the

system and module power consumptions, see "Appendix A Chassis views and technical

specifications." For power supply specifications, see "Appendix B FRUs and compatibility

matrixes."

•

The total height of the switches to be installed is not higher than the available installation height

of the rack and enough clearance is reserved for cable routing.

•

The switch is ready for installation and has been carried to a place near the rack and convenient

for moving.

Page is loading ...

Aruba JH103A Installation guide

This manual is also suitable for

Aruba JH103A Installation guide

Related papers

Other documents