Aruba JH691A Installation guide

HPE FlexFabric 5944 Switch Series

Installation Guide

P

art number: 5200-7949b

Document version: 6W102-20230310

The information contained herein is subject to change without notice. The only warranties for Hewlett Packard

Enterprise products and services are set forth in the express warranty statements accompanying such

products and services. Nothing herein should be construed as constituting an additional warranty. Hewlett

Packard Enterprise shall not be liable for technical or editorial errors or omissions contained herein.

Confidential computer software. Valid license from Hewlett Packard Enterprise required for possession, use, or

copying. Consistent with FAR 12.211 and 12.212, Commercial Computer Software, Computer Software

Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under vendor’s

standard commercial license.

Links to third-party websites take you outside the Hewlett Packard Enterprise website. Hewlett Packard

Enterprise has no control over and is not responsible for information outside the Hewlett Packard Enterprise

website.

Acknowledgments

Intel®, Itanium®, Pentium®, Intel Inside®, and the Intel Inside logo are trademarks of Intel Corporation in the

United States and other countries.

Microsoft® and Windows® are trademarks of the Microsoft group of companies.

Adobe® and Acrobat® are trademarks of Adobe Systems Incorporated.

Java and Oracle are registered trademarks of Oracle and/or its affiliates.

UNIX® is a registered trademark of The Open Group.

i

Contents

1 Preparing for installation ·········································································· 1-1

Safety recommendations ································································································································ 1-1

Examining the installation site ························································································································· 1-2

Temperature/humidity ····························································································································· 1-2

Cleanliness ·············································································································································· 1-2

Corrosive gas limit ··································································································································· 1-3

EMI ·························································································································································· 1-4

Laser safety ············································································································································· 1-4

Installation tools ·············································································································································· 1-4

Installation accessories ··································································································································· 1-4

2 Installing the switch ·················································································· 2-6

Installing the switch in a 19-inch rack·············································································································· 2-7

Installation accessories ··························································································································· 2-7

Rack-mounting procedure at a glance ···································································································· 2-8

Chassis dimensions and rack requirements ··························································································· 2-8

Attaching the mounting brackets, chassis rails, and grounding cable to the chassis······························ 2-9

Attaching the slide rails to the rack ······································································································· 2-12

Mounting the switch in the rack ············································································································· 2-13

Grounding the switch by using a grounding strip ·························································································· 2-15

Installing and removing a fan module ··········································································································· 2-16

Installing a fan module ·························································································································· 2-16

Removing a fan module ························································································································ 2-17

Installing and removing a power supply ········································································································ 2-17

Precautions ··········································································································································· 2-18

Installing a power supply ······················································································································· 2-18

Removing a power supply ····················································································································· 2-19

Connecting the power cord ··························································································································· 2-20

Connecting the power cord for a PSR450-12A/PSR450-12A1 power supply ······································· 2-20

Connecting the DC power cord for a PSR450-12D power supply ························································ 2-21

Verifying the installation ································································································································ 2-22

3 Accessing the switch for the first time ···················································· 3-23

Connecting the switch to a configuration terminal························································································· 3-23

Console cables ······································································································································ 3-23

Connecting the console cable ··············································································································· 3-24

Connecting a mini USB console cable ·································································································· 3-25

Setting terminal parameters ·················································································································· 3-26

Starting the switch ········································································································································· 3-27

4 Setting up an IRF fabric ········································································· 4-28

IRF fabric setup flowchart ····························································································································· 4-28

Planning IRF fabric setup ······························································································································ 4-29

Planning IRF fabric size and the installation site ··················································································· 4-29

Identifying the master switch and planning IRF member IDs ································································ 4-29

Planning IRF topology and connections································································································ 4-30

Identifying physical IRF ports on the member switches ········································································ 4-31

Planning the cabling scheme ················································································································ 4-31

Configuring basic IRF settings ······················································································································ 4-33

Connecting the physical IRF ports ················································································································ 4-33

Accessing the IRF fabric to verify the configuration ······················································································ 4-33

5 Maintenance and troubleshooting ·························································· 5-34

Power supply failure ······································································································································ 5-34

Symptom ··············································································································································· 5-34

Solution ················································································································································· 5-34

Fan module failure ········································································································································ 5-34

ii

Symptom ··············································································································································· 5-34

Solution ················································································································································· 5-34

Configuration terminal display issues············································································································ 5-35

No display on the configuration terminal ······························································································· 5-35

Garbled display on the configuration terminal ······················································································· 5-35

6 Appendix A Chassis views and technical specifications ························· 6-36

Chassis views ··············································································································································· 6-36

HPE 5944 48XGT 6QS28 ····················································································································· 6-36

Technical specifications ································································································································ 6-37

7 Appendix B FRUs and compatibility matrixes········································· 7-40

Power supplies ·············································································································································· 7-40

Fan modules ················································································································································· 7-41

8 Appendix C Ports and LEDs ·································································· 8-42

Ports ······························································································································································ 8-42

Console port ·········································································································································· 8-42

Management Ethernet port ··················································································································· 8-42

USB port ················································································································································ 8-44

QSFP28 port ········································································································································· 8-44

1/10GBASE-T autosensing Ethernet port ····························································································· 8-47

LEDs ····························································································································································· 8-47

System status LED ································································································································ 8-47

QSFP28 port LED ································································································································· 8-48

1/10GBASE-T autosensing Ethernet port LEDs ··················································································· 8-48

Management Ethernet port LEDs·········································································································· 8-49

Fan module alarm LEDs ······················································································································· 8-49

9 Appendix D Cooling system ··································································· 9-50

10 Document conventions and icons ························································ 9-51

Conventions ·················································································································································· 9-51

Network topology icons ································································································································· 9-52

11 Support and other resources ······························································· 9-53

Accessing Hewlett Packard Enterprise Support···························································································· 9-53

Accessing updates ········································································································································ 9-53

Websites ··············································································································································· 9-54

Customer self repair ······························································································································ 9-54

Remote support ····································································································································· 9-54

Documentation feedback ······················································································································ 9-54

Index ········································································································· 9-56

1-1

1 Preparing for installation

Table1-1 describes the HPE FlexFabric 5944 switches, power supplies, and fan modules available

for the switches.

Table1-1 HPE FlexFabric 5944 switch models and power supplies

Product code HPE description Alias

HPE FlexFabric 5944 switch series

JL836A HPE FlexFabric 5944 48XGT 6QS28 Switch HPE 5944 48XGT 6QS28

Power supplies

JL593A HPE FlexFabric 5710 450W Back-to-Front

AC Power Supply PSR450-12A

JL592A HPE FlexFabric 5710 450W Front-to-Back

AC Power Supply PSR450-12A1

JL688A HPE FlexFabric 5710 450W 48V

Front-to-Back DC Power Supply PSR450-12D

Fan module

JL838A HPE FlexFabric 5944 Power to Port Airflow

(Back to Front) Fan Module 5944 power-to-port fan module

JL837A HPE FlexFabric 5944 Port to Power Airflow

(Front to Back) Fan Module 5944 port-to-power fan module

For regulatory identification purposes, the HPE 5944 switches are assigned Regulatory Model

Number (RMN), which are listed in the following table.

Product code RMN Description

JL836A BJNGA-AD0092 HPE FlexFabric 5944 48XGT 6QS28 Switch

Safety recommendations

To avoid any equipment damage or bodily injury caused by incorrect use, read the following safety

recommendations before installation. Note that the recommendations do not cover every possible

hazardous condition.

•

Before cleaning the switch, remove all power cords from the switch. Do not clean the switch

with wet cloth or liquid.

•

Do not place the switch near water or in a damp environment. Prevent water or moisture from

entering the switch chassis.

•

Do not place the switch on an unstable case or desk. The switch might be severely damaged in

case of a fall.

•

Ensure good ventilation of the equipment room and keep the air inlet and outlet vents of the

switch free of obstruction.

•

Connect the yellow-green protection grounding cable before power-on.

•

Make sure the operating voltage is in the required range.

1-2

•

To avoid electrical shocks, do not open the chassis while the switch is operating or when the

switch is just powered off.

•

When replacing FRUs, including power supplies and fan modules, wear an ESD wrist strap to

avoid damaging the units.

Examining the installation site

The switch must be used indoors. Mount your switch in a rack and verify the following items:

•

Adequate clearance is reserved at the air inlet and outlet vents for ventilation.

•

The rack has a good ventilation system.

•

Identify the hot aisle and cold aisle at the installation site, and make sure ambient air flows into

the switch from the cold aisle and exhausts to the hot aisle.

•

Identify the airflow designs of neighboring devices, and prevent hot air flowing out of the bottom

device from entering the top device.

•

The rack is sturdy enough to support the switch and its accessories.

•

The rack is reliably grounded.

To ensure correct operation and long service life of your switch, install it in an environment that meets

the requirements described in the following subsections.

Temperature/humidity

Maintain appropriate temperature and humidity in the equipment room.

•

Lasting high relative humidity can cause poor insulation, electricity leakage, mechanical

property change of materials, and metal corrosion.

•

Lasting low relative humidity can cause washer contraction and ESD and cause problems

including loose screws and circuit failure.

•

High temperature can accelerate the aging of insulation materials and significantly lower the

reliability and lifespan of the switch.

For the temperature and humidity requirements of different switch models, see "Appendix A Chassis

views and technical specifications."

Cleanliness

Dust buildup on the chassis might cause electrostatic adsorption and dust corrosion, resulting in

poor contact of metal connectors and contact points. This might shorten the device's lifetime and

even cause communication failure. Table1-2 describes the dust concentration limits in the equipment

room.

Table1-2 Dust concentration limits in the equipment room

Substance Particle diameter Concentration limit

Dust particles ≥ 0.5 µm ≤ 3.5 × 106 particles/m3

Dust particles ≥ 5 µm ≤ 3 × 104 particles/m3

Dust (suspension) ≤ 75 µm ≤ 0.2 mg/m3

Dust (sedimentation) 75 µm to 150 µm ≤ 1.5 mg/(m2h)

To maintain cleanliness in the equipment room, follow these guidelines:

1-3

•

Keep the equipment room away from pollution sources. Do not smoke, eat, or drink in the

equipment room.

•

Use double-layer glass in windows and seal doors and windows with dust-proof rubber strips.

Use screen doors and window screens for doors and windows open to the outside and make

sure the external windows are air tight.

•

Use dustproof materials for floors, walls, and ceilings and use wallpaper or matt paint that does

not produce powders.

•

Clean the equipment room regularly and clean the air filters of the rack each month.

•

Wear ESD clothing and shoe covers before entering the equipment room, keep the ESD

clothing and shoe covers clean, and change them frequently.

Corrosive gas limit

Corrosive gases can accelerate corrosion and aging of metal components. Make sure the corrosive

gases in the equipment room do not exceed the concentration limits as shown in Table1-3.

Table1-3 Corrosive gas concentration limits in the equipment room

Gas Average concentration (mg/m3) Maximum concentration (mg/m3)

SO2 0.3 1.0

H2S 0.1 0.5

Cl2 0.1 0.3

HCI 0.1 0.5

HF 0.01 0.03

NH3 1.0 3.0

O3 0.05 0.1

NOX 0.5 1.0

CAUTION:

As a best practice, control the

corrosive gas concentrations in the equipment room at their

average

values

. Make sure the corrosive gas concentrations do not exceed 30 minutes per day at their

maximum values.

To control corrosive gases, use the following guidelines:

•

As a best practice, do not build the equipment room in a place with a high concentration of

corrosive gases.

•

Make sure the equipment room is not connected to sewer, vertical shaft, or septic tank pipelines

and keep it far away from these pipelines. The air inlet of the equipment room must be away

from such pollution sources.

•

Use environmentally friendly materials to decorate the equipment room. Avoid using organic

materials that contains harmful gases, such as sulfur or chlorine-containing insulation cottons,

rubber mats, sound-proof cottons, and avoid using plasterboards with high sulfur concentration.

•

Place fuel (diesel or gasoline) engines separately. Do not place them in the same equipment

room with the device. Make sure the exhausted air of the engines will not flow into the

equipment room or towards the air inlet of the air conditioners.

•

Place batteries separately. Do not place them in the same room with the device.

•

Employ a professional company to monitor and control corrosive gases in the equipment room

regularly.

1-4

EMI

All electromagnetic interference (EMI) sources, from outside or inside of the switch and application

system, adversely affect the switch in the following ways:

•

A conduction pattern of capacitance coupling.

•

Inductance coupling.

•

Electromagnetic wave radiation.

•

Common impedance (including the grounding system) coupling.

To prevent EMI, use the following guidelines:

•

If AC power is used, use a single-phase three-wire power receptacle with protection earth (PE)

to filter interference from the power grid.

•

Keep the switch far away from radio transmitting stations, radar stations, and high-frequency

devices.

•

Use electromagnetic shielding, for example, shielded interface cables, when necessary.

•

To prevent signal ports from getting damaged by overvoltage or overcurrent caused by lightning

strikes, route interface cables only indoors.

Laser safety

WARNING

!

•

The switch is a Class 1M laser device.

•

Disconnected optical fibers or transceiver modules might emit invisible laser light. Do not stare

into beams or view directly with optical instruments when the switch is operating.

Installation tools

No installation tools are provided with the switch. Prepare the following tools yourself:

•

Phillips screwdriver.

•

Flathead screwdriver.

•

ESD wrist strap.

•

Marker.

Installation accessories

Before installation, make sure you have all the required installation accessories. If any accessory is

damaged or missing, use the part No. provided in this table to purchase a new one.

Table1-4 Installation accessories

Part No. Description Quantity Applicable

device models

5066-0850

Mounting brackets

1 pair, provided

(If the mounting bracket

has a small round role,

you can use the hole to

hang the asset tag.)

HPE 5944 48XGT

6QS28

1-5

5185-8713

1U rack mounting rail kit A (long

slide rails)

1 kit, provided HPE 5944 48XGT

6QS28

5185-8681

1U rack mounting rail kit B

Optional HPE 5944 48XGT

6QS28

N/A M6 screw and cage nut

User supplied HPE 5944 48XGT

6QS28

5080-0012

Grounding cable

1, provided HPE 5944 48XGT

6QS28

5185-9579 Grounding screw

2, provided HPE 5944 48XGT

6QS28

5190-1773

Power supply filler panel

1, provided HPE 5944 48XGT

6QS28

5185-8748 Releasable cable tie

User supplied HPE 5944 48XGT

6QS28

5185-8627

Serial console cable

Optional HPE 5944 48XGT

6QS28

N/A

Mini USB console cable

User supplied HPE 5944 48XGT

6QS28

5185-8722

SFP port plug

Same number as the

SFP ports HPE 5944 48XGT

6QS28

5187-9022

QSFP port plug

Same number as the

QSFP28 ports HPE 5944 48XGT

6QS28

2-6

2 Installing the switch

CAUTION:

Keep the tamper

-

proof seal on a mounting screw on the chassis cover intact, and if you want to open

the chassis, contact

Hewlett Packard Enterprise for permission. Otherwise, Hewlett Packard

Enterprise shall not be liable for any consequence caused thereby.

CAUTION:

Always wear an ESD wrist strap during the installation process

. Make sure the wrist strap makes

good skin contact and is reliably grounded.

Figure2-1 Hardware installation flow

Start

Ground the switch

Install fan modules

Install power supplies

Connect power cords

Verify the installation

Turn on the circuit

breakers Troubleshoot

the switch

Operating

correctly？

End

No

Yes

Turn off the

circuit breakers

Install the switch

2-7

Installing the switch in a 19-inch rack

Installation accessories

Table2-2 Installation accessories

Switch model Mounting brackets Rack mounting rail kit

HPE 5944 48XGT

6QS28

1U high, one pair

(provided). See Figure2-2.

If the mounting bracket has

a small round role, you can

use the hole to hang the

asset tag.

• 1U rack mounting rail kit A, including one pair of

chassis rails and one pair of long slide rails

(provided). See Figure2-3.

• 1U rack mounting rail kit B, including one pair of

chassis rails and one pair of slide rails

(optional). See Figure2-4.

Figure2-2 Mounting brackets

Figure2-3 1U rack mounting rail kit A (long slide rails)

(1) Chassis rail

(2) Long slide rail

1 2

2-8

Figure2-4 1U rack mounting rail kit B

(1) Chassis rail

(2) Slide rail

Rack-mounting procedure at a glance

Figure2-5 Rack-mounting procedure

NOTE:

If

a rack shelf is available, you can put the switch on the rack shelf,

slide the switch to an appropriate

location, and attach the switch to the rack with the mounting brackets.

Chassis dimensions and rack requirements

Figure2-6 HPE 5944 48XGT 6QS28 chassis dimensions with the mounting brackets installed

at the port side

(1) Power supply handle

(2) Mounting bracket

1 2

Attach the

mounting

brackets to the

switch

Attach the

chassis rails to

the switch

Connect the

grounding cable

to a grounding

point

Select an installation position

for the mounting brackets

(near the port side or power

supply side)

Mount the

switch in the

rack

Attach the

slide rails to

the rack

2-9

Figure2-7 HPE 5944 48XGT 6QS28 chassis dimensions with the mounting brackets installed

at the power supply side

(1) Power supply handle

(2) Mounting bracket

Follow these guidelines when you install the switch in a 19-inch rack:

•

The distance between the front and rear posts of the rack must meet the requirements

described in Table2-3.

•

To secure the switch to the rack, you must install not only mounting brackets, but also chassis

rails and slide rails.

Table2-3 Distance requirements between the front and rear rack posts

Switch model Installation method Distance between the front and

rear rack posts

HPE 5944 48XGT

6QS28

Using mounting brackets and rack

mounting rail kit A (long slide rails) 621 mm to 854 mm (24.45 in to 33.62 in)

Using mounting brackets and rack

mounting rail kit B 401 mm to 634 mm (15.79 in to 24.96 in)

Table2-4 Chassis dimensions and rack depth requirements

Device

model Chassis dimensions Rack depth requirement

HPE 5944

48XGT

6QS28

• Height—44 mm (1.73 in) (1 RU)

• Width—440 mm (17.32 in).

• Total depth—485 mm (19.09 in)

 25 mm (0.98 in) for the power

supply or fan module handle

 460 mm (18.11 in) for the

chassis.

To ensure that the rack door can be closed

easily after cables are connected, make sure

the rack meets the following requirements:

• A minimum of 800 mm (31.50 in) in depth

(recommended)

• A minimum of 130 mm (5.12 in) from the

front rack post to the front door

• A minimum of 509 mm (20.04 in) from

the front rack post to the rear door

Attaching the mounting brackets, chassis rails, and

grounding cable to the chassis

The switch has two mounting bracket installation positions on its two side panels: one near the

network port side and one near the power supply side.

The switch provides a primary grounding point (with a grounding sign) and an auxiliary grounding

point.

Figure2-8 describes these positions on the HPE 5944 48XGT 6QS28 switch.

2-10

Figure2-8 Mounting bracket installation positions and grounding point positions on the HPE

5944 48XGT 6QS28 switch

(1) Mounting bracket installation position near the power supply side

(2) Primary grounding point

(3) Auxiliary grounding point

(4) Mounting bracket installation position near the port side

Attaching the mounting brackets and chassis rails to the chassis

IMPORTANT:

M4 screws are used to secure the mounting brackets and chassis rails to the switch.

As a best

practice, use a torque of 12 kgf-cm (1.18 Nm) to fasten M4 screws.

To attach the mounting brackets and chassis rails to the chassis:

1. Place the wide flange of a mounting bracket against a side panel of the chassis and align the

round holes in the wide flange of the front mounting bracket with the screw holes in the side

panel. Then use M4 screws (provided) to attach the mounting bracket to the chassis.

 To install the mounting brackets at the port side, see Figure2-9.

 To install the mounting brackets at the power supply side, see Figure2-10.

2. Determine the chassis rail installation position based on the mounting bracket installation

position.

3. Place the chassis rail against the side panel of the chassis and align the installation holes in the

chassis rail with rail mounting holes in the chassis. Then use M4 screws (provided) to attach the

chassis rail to the chassis. For installation of chassis rails of rack mounting rail kit A (long slide

rails) and rack mounting rail kit B, see Figure2-9 and Figure2-10.

4. Follow the same procedure to attach another mounting bracket and chassis rail to the opposite

side.

2-11

Figure2-9 Attaching the mounting brackets and chassis rails to an HPE 5944 48XGT 6QS28

(mounting brackets installed near the port side, rack mounting rail kit A or B)

Figure2-10 Attaching the mounting brackets and chassis rails to an HPE 5944 48XGT 6QS28

switch (mounting brackets installed near the power supply side, rack mounting rail kit A or

B)

Connecting the grounding cable to the chassis

IMPORTANT:

The primary and auxiliary grounding point

s are located on the left side panel of the

chassis. The two

grounding points

might be not reachable after the switch is mounted in the rack. Connect the

grounding cable to a grounding point before you mount the switch in the rack.

To connect the grounding cable to a grounding point:

1. Unpack the grounding cable and grounding screws (applicable to both the primary and auxiliary

grounding points).

2. Use the grounding screws to attach the two-hole grounding lug to the grounding point and then

fasten the screws (clockwise direction), as shown in Figure2-11.

As a best practice, use a torque of 30 kgf-cm (2.94 Nm) to fasten the grounding screws.

2-12

Figure2-11 Attaching the grounding cable to the primary grounding point on an HPE 5944

48XGT 6QS28 switch

Attaching the slide rails to the rack

IMPORTANT:

M

6 screws and cage nuts are used to attach the slide rails to the rack. P

repare M6 screws and cage

nuts yourself. As a best practice, use a torque of 30 kgf-cm (2.94 Nm) to fasten the M6 screws.

Before mounting the switch in the rack, you must attach slide rails to the rack.

The installation procedure is the same for different types of slide rails. The following procedure

attaches 1U long slide rails to the rack.

To attach the slide rails to the rack:

1. Identify the slide rail installation position on the rack based on the switch installation position.

2. Install cage nuts (user-supplied) in the mounting holes in the rack posts.

3. Align the screw holes in one slide rail with the cage nuts in a rear rack post, and then use M6

screws (user-supplied) to attach the slide rail to the rack, as shown in Figure2-12.

4. Attach the other slide rail to the rear rack post on the opposite side.

Make sure the two slide rails are at the same height and can slide into the chassis rails

smoothly.

2-13

Figure2-12 Installing the 1U long slide rails

Mounting the switch in the rack

1. Wear an ESD wrist strap and make sure it makes good skin contact and is reliably grounded.

2. Verify that the mounting brackets and chassis rails have been securely attached to the switch

chassis.

3. Verify that the slide rails have been correctly attached to the rear rack posts.

4. Attach cage nuts (user-supplied) to the front rack posts and make sure they are at the same

level as the slide rails.

5. One person performs the following operations:

a. Supporting the bottom of the switch, aligns the chassis rails with the slide rails on the rack

posts.

b. Pushes the switch slowly for the slide rails to slide into the chassis rails smoothly until the

mounting brackets are flush against the front rack posts. Make sure the front ends of the

slide rails reach out of the chassis rails.

6. The other person uses screws (user-supplied, rust-proofed) to attach the mounting brackets to

the rack.

2-14

Figure2-13 Mounting an HPE 5944 48XGT 6QS28 switch in the rack (mounting brackets

installed near the power supply side)

Figure2-14 Mounting an HPE 5944 48XGT 6QS28 switch in the rack (mounting brackets

installed near the port side)

2-15

Grounding the switch by using a grounding strip

CAUTION:

•

Correctly connecting the grounding cable is crucial to lightning protection and EMI protection.

•

Do not connect the grounding cable to a fire main or lightning rod.

•

To guarantee the grounding effect and avoid switch damage, use the grounding cable provided

with the switch to connect the switch to a grounding strip in the equipment room.

The power input end of the switch has a noise filter, whose central ground is directly connected to the

chassis to form the chassis ground (commonly known as PGND). You must securely connect this

chassis ground to the earth so the faradism and leakage electricity can be safely released to the

earth to minimize EMI susceptibility of the switch.

To ground the switch by using a grounding strip:

1. Attach the two-hole grounding lug at one end of the grounding cable to a grounding point on the

switch chassis. For more information, see "Connecting the grounding cable to the chassis."

2. Remove the hex nut of a grounding post on the grounding strip.

3. Attach the ring terminal at the other end of the grounding cable to the grounding post on the

grounding strip, and secure the ring terminal to the grounding post with the hex nut.

Figure2-15 Connecting the grounding cable to a grounding strip

(1) Hex nut

(2) Ring terminal

(3) Grounding post

(4) Grounding strip

1

234

2-16

Installing and removing a fan module

CAUTION:

•

For adequate heat dissipation, you must install five fan modules of the same model for the

switch.

•

Do not install fan trays of different models on the same switch.

•

Make sure all slots have a module installed when the switch is operating.

•

If more than one fan module fails during switch operation, do not remove the failed fan module

s

simultaneously. Replace the fan modules one by one and finish replacing each fan module

within

three minutes.

CAUTION:

Select fan trays and power supplies that have the airflow direction matching the

ventilation

requirements at the installation site

.

As a best practice, make sure the power supplies and fan trays

on the switch have the same airflow direction. For the fan tr

ays available for the switch and their

specifications, see Appendix B FRUs and compatibility matrixes.

Installing a fan module

CAUTION:

To prevent damage to the fan

module or the connectors on the backplane, insert the fan module

gently. If you encounter a hard resistance while inserting the fan

module, pull out the fan module

and

insert it again.

Select fan modules for the switch as needed. For the fan modules available for the switch and their

specifications, see "Fan modules."

The installation procedure is the same for different models of fan trays.

To install a fan module:

1. Wear an ESD wrist strap and make sure it makes good skin contact and is reliably grounded.

2. Unpack the fan module and verify that the fan module model is correct.

3. Orient the fan module with the "TOP" mark facing upward. Grasp the handle of the fan module

with one hand and support the fan module bottom with the other, and slide the fan module along

the guide rails into the slot until the fan module is fully seated in the slot and has a firm contact

with the backplane.

Figure2-16 Installing an HPE 5944 power-to-port fan module

Page is loading ...

Aruba JH691A Installation guide

Aruba JH691A Installation guide

Related papers

Other documents