HPE 5960 400G 1600W AC
Power Supply (R9Y18A) User Guide
P
art number: 5200-8654
Document version: AP100-20221220
© Copyright 2022 Hewlett Packard Enterprise Development LP
The information contained herein is subject to change without notice.
The only warranties for Hewlett Packard Enterprise products and
services are set forth in the express warranty statements
accompanying such products and services. Nothing herein should be
construed as constituting an additional warranty. Hewlett Packard
Enterprise shall not be liable for technical or editorial errors or
omissions contained herein.
Confidential computer software. Valid license from Hewlett Packard
Enterprise required for possession, use, or copying. Consistent with
FAR 12.211 and 12.212, Commercial Computer Software, Computer
Software Documentation, and Technical Data for Commercial Items
are licensed to the U.S. Government under vendor’s standard
commercial license.
Links to third-party websites take you outside the Hewlett Packard
Enterprise website. Hewlett Packard Enterprise has no control over
and is not responsible for information outside the Hewlett Packard
Enterprise website.
Acknowledgments
Intel®, Itanium®, Pentium®, Intel Inside®, and the Intel Inside logo
are trademarks of Intel Corporation in the United States and other
countries.
Microsoft® and Windows® are either registered trademarks or
trademarks of Microsoft Corporation in the United States and/or other
countries.
Adobe® and Acrobat® are trademarks of Adobe Systems
Incorporated.
Java and Oracle are registered trademarks of Oracle and/or its
affiliates.
UNIX® is a registered trademark of The Open Group.
i
Contents
About the power supply ······································ 1
Overview ·················································································· 1
Technical specifications ···························································· 1
Views ························································································ 2
LEDs························································································· 3
Power cords ·············································································· 3
Installing and removing the power supply··········· 3
Safety precautions ···································································· 3
Installation tools ········································································ 4
Installing the power supply ························································ 4
Connecting the power cord ······················································· 6
Removing the power supply ······················································ 8
1
About the power supply
Overview
The HPE 5960 400G 1600W AC Power Supply (R9Y18A) is a
high-voltage DC (for China only) or AC input power supply. It
provides a maximum output of 1600 W.
The power supply has the following features:
• Protection—The power supply provides protection against input
overcurrent, input undervoltage, output overcurrent, output
overvoltage, output short circuit, and overtemperature conditions.
• Redundancy—Two or more of the power supplies can be
connected in parallel to achieve N+1 or N+N redundancy and load
sharing.
• Hot swapping—The power supply can be installed on or
removed from an operating device. You can remove a power
supply only when the remaining power supplies can provide
sufficient power for the device.
Technical specifications
Item Specification
Rated AC input voltage range 100 to 240 VAC @ 50 to 60 Hz
Rated HVDC input voltage
range (for China only) 180 to 320 VDC
Output voltage 12 V
Maximum output current 133 A
Maximum output power 1600 W
Dimensions (H × W × D)
40.0 × 54.5 × 363.8 mm
2
Item Specification
(including the handle)
(1.57 × 2.15 × 14.32 in)
Operating temperature –10°C to +55°C (+14°F to
+131°F)
Operating relative humidity 5% to 95%
Airflow direction From the port side to the power
supply side
Views
Figure 1 PSR1600C-12A-B power supply view
(1) Fault LED (!)
(2) Power output LED (OUT)
(3) Power input LED (IN)
(4) Power input receptacle
(5) Latch
(6) Handle
3
6
4
5
2
1
3
LEDs
The power supply provides three LEDs to indicate its operating
status.
Table 1 LED descriptions
LED Mark Status Description
Power input
LED IN
Steady green Normal power input
Off No power input or
overvoltage power
input
Power
output LED OUT Steady green Normal power output.
Off No power output
Fault LED ！ Flashing
yellow A fault has occurred.
Off No fault has occurred.
Power cords
The power supply supports two types of AC power cords: one type
for connecting to a PDU and the other type for connecting to an AC
outlet.
Installing and removing the power
supply
Safety precautions
To avoid bodily injury or power supply or device damage, follow these
safety precautions:
4
•
When installing and removing the power supply, wear an ESD
wrist strap. Make sure the strap makes good skin contact and is
reliably grounded.
•
To avoid power supply or device damage, make sure the
external power source provides a voltage as required by the
power supply and the power supply output voltage is as required
by the device.
•
To avoid bodily injury, do not touch any bare cables or terminals
of the power supply.
•
Do not place the power supply in a wet area, and prevent liquid
from flowing into the power supply.
•
To avoid power supply damage, do not open the power supply.
When an internal circuit or component is faulty, contact HPE
Support.
Installation tools
You must wear an ESD wrist strap when installing or removing the
power supply. Prepare one yourself.
Installing the power supply
To avoid bodily injury or device damage, strictly follow the procedure
in Figure 2 to install the power supply.
5
Figure 2 Power supply installation procedure
To install the power supply:
1. Wear an ESD wrist strap, and make sure the strap makes good
skin contact and is reliably grounded.
2. Unpack the power supply. Make sure the power supply model is
as required.
3. As shown in Figure 3, correctly orient the power supply. Holding
the power supply handle with one hand and supporting its
bottom with the other, align it with the power supply slot. Push
the power supply slowly into the slot along the guide rails until
the latch clicks and locks in place.
Make sure the power supply makes good contact with the
backplane connector of the device.
If you encounter a hard resistance while inserting the power
supply, pull out the power supply, orient it correctly, and then
insert it again.
Install the power supply
Connect the power cord
Turn on the circuit breaker
6
Figure 3 Installing the power supply
IMPORTANT:
Keep the filler panel for
the power supply slot and the power
supply packaging materials secure for future use.
Connecting the power cord
WARNING!
•
Make sure each power cord has a separate circuit breaker.
•
Before connecting the power cord, make sure the circuit
breaker for it is turned off.
To connect the power cord:
1. As shown in Figure 4, connect the female connector (IEC
60320-C15) of the power cord into the power input receptacle
on the power supply.
7
Figure 4 Connecting the power cord
2. As shown in Figure 5, use a cable tie to secure the power cord to
the handle of the power supply.
Figure 5 Securing the power cord
3. Connect the other end of the power cord to an external AC or
HVDC power source and turn on the circuit breaker.
4. Examine the power input status LED (IN) on the power supply.
If the LED is steady green, the power cord is connected
correctly. If the LED is off, check the installation and fix the
issues.
12
8
Removing the power supply
To avoid bodily injury or device damage, strictly follow the procedure
in Figure 6 to remove the power supply.
Figure 6 Power supply removal procedure
To remove the power supply:
1. Turn off the circuit breaker.
2. Wear an ESD wrist strap, and make sure the strap makes good
skin contact and is reliably grounded.
3. Loosen and remove the cable tie, and then remove the power
cord.
4. As shown in Figure 7, use one hand to hold the power supply
handle, press the latch towards the handle, and then pull the
power supply part way out of the slot. Supporting the power
supply with the other hand, pull it completely out of the slot.
Turn off the circuit breaker
Disconnect the power cord
Remove the power supply
9
Figure 7 Removing the power supply
5. Place the removed power supply on an anti-static mat or put it
into its original package.
6. If you are not to install a new power supply, install a filler panel in
the slot to prevent dust and ensure good ventilation in the
device.
1
2
/