ASRock Rack GENOAD8HM3 Installation guide
- Category
- Motherboards
- Type
- Installation guide
GENOAD8HM3
Quick Installation Guide
www.asrockrack.com GENOAD8HM3
2
P/N: 15G065299000AK V1.0
Motherboard Layout
The server board User's Manual is available for download from the ASRock Rack's ocial website
at http://www.asrockrack.com.
Take note of the following precautions before installing server board components or change any
server board settings.
1. Unplug the power cord from the wall socket before touching any components.
2. To avoid damaging the server board’s components due to static electricity, NEVER place the
server board directly on the carpet or the like. Also remember to use a grounded wrist strap or
touch a safety grounded object before you handle the components.
3. Hold components by the edges and do not touch the ICs.
4. Whenever uninstall any component, place it on a grounded anti-static pad or in the bag that
comes with the component.
5. When placing screws into the screw holes to secure the server board to the chassis, please do
not over-tighten the screws! Doing so may damage the server board.
*15G065299000AK*
Install the Server Board1
1Insert the server board into the chassis.
2Affix the screws clockwise into the
mounting holes in all of the corners of
the server board.
Do not over-tighten the screws
I/O Panel3
4 Jumper Settings
When the jumper cap is placed on the pins, the jumper
is “Short”. If no jumper cap is placed on the pins, the
jumper is “Open”.
e illustration shows a 3-pin jumper whose pin1 and
pin2 are “Short” when a jumper cap is placed on these
2 pins.
VGA1
IPMI_LAN1
UID1
USB 3.2
Gen1
B: USB1
M2_2
COM1
BUZZER1
BMC
ROM
FRNT_VGA
CM_SB_R1
SPEAKER1
PWM_CFG1
CPU1
PSU_SMB1
CPU_HSBP1
USB3_3_4 ATX12V1
ATX12V2
HDD_PWR1
FAN1
FAN2
FAN3
FAN4
FAN5
FAN6
FAN7
FAN8
ATX12V3
ITX_AUX_PANEL1
AUX_PANEL1
J1
PANEL1
SATA_SGPIO1
SATA_SGPIO2
SATA_SGPIO3
OCU1
M2_1
TPM_BIOS_PH1
BIOS
ROM
IPMB1 BMC_SMB1
IPMI_LED1
T: USB2
DDR5_E1
DDR5_C1
DDR5_B1
DDR5_A1
DDR5_H1
DDR5_G1
DDR5_I1
DDR5_K1
PCIE 2
PCIE 1
PCIE 3
MCIO8
MCIO6
MCIO7
MCIO2
MCIO3
MCIO1
MCIO5
MCIO4
BAT1
ASPEED
AST2600
Dr. Debug
OCP1
CLRMOS1
NUT80_2 NUT110_2
NUT80_1
NUT110_1
GENOAD8HM3
NMI_BTN1
16.8cm (6.6in)
8.1cm (3.2in)
43.2cm (17in)
10
11
12
45
2
4
5
6
7
46
1
13
14
15
16
17
18
19
20
21
24 23 22
2527 2629
34 33 32 31 30
37
36
35
39
38
47
48
49
42
44
28
8
50
51
52
53
3
43
9
40
41
No. Description
1 Serial Port Header (COM1)
2 Front VGA Header (FRNT_VGA)
3 IPMI LAN LED Header (IPMI_LED1)
4Intelligent Platform Management Bus
Header (IPMB1)
5 PCI Express 5.0 x16 Slot (PCIE1)
6 BMC SMBus Header (BMC_SMB1)
7 Clear CMOS Pad (CLRMOS1)
8Speaker Header (SPEAKER1)
9Non Maskable Interrupt Button
(NMI_BTN1)
10 CM Board Standby Power Header
(CM_ SB_R1)
11 M.2 Socket (M2_2)
(Type 2280/22110)
12 PWM Conguration Header
(PWM_CFG1)
13 2 x 288-pin DDR5 DIMM Slots
(DDR5_A1, DDR5_C1)
14 2 x 288-pin DDR5 DIMM Slots
(DDR5_B1, DDR5_E1)
15 LGA-6096 CPU Socket (CPU1)
16 Mini Cool Edge IO Connector (MCIO3)
17 Mini Cool Edge IO Connector (MCIO1)
18 Mini Cool Edge IO Connector (MCIO2)
19 PSU SMBus Header (PSU_SMB1)
20 Backplane PCI Express Hot-Plug
Connector (CPU1_HSBP1)
21 USB 3.2 Gen1 Header (USB3_3_4)
22 ATX 12V Power Connector (ATX12V1)
23 ATX 12V Power Connector (ATX12V2)
24 Mini Cool Edge IO Connector (MCIO4)
25 HDD Power Connector (HDD_PWR1)
26 System Fan Connector (FAN1)
27 System Fan Connector (FAN2)
No. Description
28 System Fan Connector (FAN3)
29 System Fan Connector (FAN4)
30 System Fan Connector (FAN5)
31 System Fan Connector (FAN6)
32 System Fan Connector (FAN7)
33 System Fan Connector (FAN8)
34 Mini Cool Edge IO Connector (MCIO5)
35 ATX 12V Power Connector (ATX12V3)
36 ITX Auxiliary Panel Header
(ITX_AUX_PANEL1)
37 Auxiliary Panel Header (AUX_PANEL1)
38 System Panel Header (PANEL1)
39 Front Panel Board Header (J1)
40 SATA SGPIO Connector
(SATA _ SGPIO1)
41 SATA SGPIO Connector
(SATA_SGPIO2)
42 SATA SGPIO Connector
(SATA_SGPIO3)
43 Mini Cool Edge IO Connector (MCIO6)
44 Mini Cool Edge IO Connector (MCIO8)
45 Mini Cool Edge IO Connector (MCIO7)
46 2 x 288-pin DDR5 DIMM Slots
(DDR5_K1, DDR5_H1)
47 2 x 288-pin DDR5 DIMM Slots
(DDR5_I1, DDR5_G1)
48 M.2 Socket (M2_1) (Type 2280/22110)
49 OCuLink Connector (2 SATA 6Gb/s)
(OCU1)
50 SPI TPM Header (TPM_BIOS_PH1)
51 PCI Express 5.0 x8 Slot (PCIE3)
52 PCI Express 5.0 x16 Slot (PCIE2)
53 OCP 3.0 Gen4 x16 Mezzanine Card Slot
(OCP1)
4
23
1
No. Description No. Description
1 UID Switch (UID1) 3 LAN RJ-45 Port (IPMI_LAN1)
2 USB 3.2 Gen1 Ports (USB3_1_2) 4 Mini DisplayPort (VGA1)
GENOAD8HM3
Quick Installation Guide
www.asrockrack.com GENOAD8HM3
8Install the PCIE Card
6LAN Port LED Indications
IPMI LAN Port Activity / Link LED Speed LED
Status Description Status Description
O No Link O 10Mbps connection or no
link
Blinking Yellow Data Activity Yellow 100Mbps connection
On Link Green 1Gbps connection
7M.2 SSD Module Installation
9Install the Memory
1
2
3
Unlock a DIMM slot by pressing
the module clips outward.
Insert the memory module.
Lock the clips.
2Move the stando based on the module type and
length.
3Peel o the yellow protective lm on the nut.
Hand tighten the stando into the desired
location.
Gently insert the M.2 module into the slot.
4
Tighten the screw with a screwdriver to secure
the module into place. Please do not overtighten
the screw.
5
2
1
AB
1Find the corresponding nut location to be used.
AB
AB
AB
AB 20o
NUT1NUT2B
LAN Port
ACT/LINK LED
SPEED LED
No. 1 2
Nut Location A B
PCB Length 8cm 11cm
Module Type Type2280 Type 22110
We recommend using the CPU Installation tool to avoid CPU pin-bent problem.
5
Locate the screw on the CPU socket and
unscrew it. Open the rst retention cover.
Open the second bracket. Take out the
internal plastic cover.
Install CPU along with the carrier frame,
do not separate them. Please make sure the
carrier frame with CPU is closely attached
to the rail frame while inserting it.
Close the bracket that holds the CPU. Close
the retention cover and fasten the screw .
Install the Processor and Heatsink
Install the heatsink to the CPU carrier.
Secure the heastink to the CPU carrier
with a screwdriver.
1
2
3
4
5
Install the carrier frame with CPU. Don’t separate them.
Please mak e sure that the carrier
frame with CPU is closely attached to
the rail fra me whi le inser ting it.
Carrier Fram e with CPU
Rail Frame
6
7
8
9
10
10-5
10-3 10-1
10-6
10-4
10-2
Set your torque wrench to 1.54 in-lb.
One fourth a turn each time.
Tighten the screws in a sequential order
1 > 2 > 3 > 4 > 5 > 6.
Loosen the screws in a reverse order.
1Remove the bracket facing the slot
that intending to use on the chassis.
Keep the screw for later use.
Align the riser-card assembly
connector with the slot on the
system board. Press rmly until the
riser-card assembly is completely
seated on the slot.
Fasten the card to the chassis with
the screw.
*Images shown are for illustrative purposes only and may dier depending on
model.
2Install the PCIE card to the riser
card.
4
If having any queries related to the riser card,
please contact the local sales representative or
technical support team.
Slot Generation Mechanical Electrical Source
PCIE1 5.0 x16 x16 CPU1
PCIE2 5.0 x16 x16 CPU1
PCIE3 5.0 x8 x8 CPU1
3
-
1
-
2
ASRock Rack GENOAD8HM3 Installation guide
- Category
- Motherboards
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
ASRock Rack GENOAD8X-2T/BCM Installation guide
-
-
-
-
-
ASRock Rack GENOAD8UD-2T/X550 Installation guide
-
-
-
-