ASRock Rack GENOAD8UD-2T/X550 Installation guide
- Category
- Motherboards
- Type
- Installation guide
GENOAD8UD-2T | GENOAD8UD-2T/X550
Quick Installation Guide
www.asrockrack.com GENOAD8UD-2T GENOAD8UD-2T/X550
2
P/N: 15G065264000AK V1.0
Motherboard Layout
The server board User's Manual is available for download from the ASRock Rack's ocial website
at http://www.asrockrack.com.
Take note of the following precautions before you install server board components or change any
server board settings.
1. Unplug the power cord from the wall socket before touching any components.
2. To avoid damaging the server board’s components due to static electricity, NEVER place your
server board directly on the carpet or the like. Also remember to use a grounded wrist strap or
touch a safety grounded object before you handle the components.
3. Hold components by the edges and do not touch the ICs.
4. Whenever you uninstall any component, place it on a grounded anti-static pad or in the bag
that comes with the component.
5. When placing screws into the screw holes to secure the server board to the chassis, please do
not over-tighten the screws! Doing so may damage the server board.
*15G065264000AK*
Install the Server Board1
1Insert the server board into the chassis.
2Affi x the screws clockwise into the
mounting holes in all of the corners of
the server board.
Do not over-tighten the screws
I/O Panel3
6
5
3
4
2
1
No. Description No. Description
1 UID Switch (UID1) 4 10G LAN RJ-45 Port (LAN1)
2 IPMI LAN Header (IPMI_LAN1) 5 10G LAN RJ-45 Port (LAN2)
3 USB 3.2 Gen1 Ports (USB3_1_2) 6 VGA Port (VGA1)
26.7cm (10.5 in)
26.4cm (10.4 in)
23
10
11
13
1
SPEAKER1
14
15
17
18
19
20
22
23
2627
1
21
2425
FAN1
FAN2
FAN3
DDR5_G1
SA TA PWR1
MCIO1
M2_1
SA TA _SGPIO3
CPU_HSBP1
Dr. Debug
AUX_P ANEL1
PA NEL1
4
5
6
8
9
12
16
283233 293134
41
38
40
39
42
1
T
R1
Super
I/O
CLRMOS1
30
GENOAD8UD-2T
GENOAD8UD-2T/X550
ATX12V2
ATX12V1
ATX4PIN1
BAT1
FAN4
FAN5
FAN6
ATX12V3
MCIO2
MCIO3
MCIO4
MCIO5
PSU_SMB1
CPU1
US B 3. 2 Gen1
T: USB_ 2
B: USB_ 1
(NCSI)
IPMI_LAN
LAN_1 LAN_2
UID1
APEED
AST2600
BIOS
ROM
TPM_BIOS_PH1
VGA1
PCIE6
PCIE5
PCIE4
DDR5_A1
DDR5_B1
DDR5_C1
DDR5_E1
USB3_3_4
COM1
IPMB1
BMC_SMB1
BMC
ROM
PCIE3
M2_2
SA TA _SGPIO4
1
NMI_BTN1
BUZZER1
DDR5_K1
DDR5_I1
DDR5_H1
353637
7
GENOAD8UD-2T :
Intel
X710- AT 2
GENOAD8UD-2T/X550:
Intel
X550- AT 2
No. Description
12 x 288-pin DDR5 DIMM Slots
(DDR5_G1, DDR5_I1)
22 x 288-pin DDR5 DIMM Slots
(DDR5_H1, DDR5_K1)
3ATX 4-PIN Power Connector
(ATX4PIN1 (ATX 24pin-to-4pin))
4 ATX 12V Power Connector (ATX12V1)
5 ATX 12V Power Connector (ATX12V2)
6 ATX 12V Power Connector (ATX12V3)
7 AMD Socket SP5 (SM-LGA-6096) (CPU1)
8 System Fan Connector (FAN1)
9 System Fan Connector (FAN2)
10 System Fan Connector (FAN3)
11 System Fan Connector (FAN4)
12 System Fan Connector (FAN5)
13 System Fan Connector (FAN6)
14 2 x 288-pin DDR5 DIMM Slots
(DDR5_A1, DDR5_C1)
15 Mini Cool Edge IO x8 Connector (MCIO1)
16 2 x 288-pin DDR5 DIMM Slots
(DDR5_B1, DDR5_E1)
17 Mini Cool Edge IO x8 Connector (MCIO2)
18 Mini Cool Edge IO x8 Connector (MCIO3)
19 M.2 Socket (M2_1)
(Type 2230/2242/2260/2280)
20 Mini Cool Edge IO x8 Connector (MCIO4)
21 Mini Cool Edge IO x4 Connector (MCIO5)
22 Backplane PCI Express Hot-Plug Connector
(CPU1_HSBP1)
23 SATA Power Connector (SATAPWR1)
24 M.2 Socket (M2_2)
(Type 2230/2242/2260/2280)
25 PSU SMBus Header (PSU_SMB1)
26 System Panel Header (PANEL1)
27 SATA SGPIO Connector (SATA_SGPIO4)
28 Auxiliary Panel Header (AUX_PANEL1)
29 SATA SGPIO Connector (SATA_SGPIO3)
30 USB 3.2 Gen1 Header (USB3_3_4)
31 Chassis Speaker Header (SPEAKER1)
32 Clear CMOS Pad (CLRMOS1)
33 Non Maskable Interrupt Button
(NMI_BTN1)
34 ermal Sensor Header (TR1)
35 Intelligent Platform Management Bus
Header (IPMB1)
36 BMC SMBus Header (BMC_SMB1)
37 COM Port Header (COM1)
38 PCI Express 5.0 x16 Slot (PCIE3)
39 PCI Express 5.0 x16 Slot (PCIE4)
40 PCI Express 5.0 x16 Slot (PCIE5)
41 PCI Express 5.0 x16 Slot (PCIE6)
42 SPI TPM Header (TPM_BIOS_PH1)
4 Install the Memory
1
2
3
Unlock a DIMM slot by
pressing the module clips
outward.
Insert the memory module.
Lock the clips.
GENOAD8UD-2T | GENOAD8UD-2T/X550
Quick Installation Guide
www.asrockrack.com GENOAD8UD-2T GENOAD8UD-2T/X550
6LAN Port LED Indications
We recommend using the CPU Installation tool to avoid CPU pin-bent problem.
5
Locate the screw on the CPU socket and
unscrew it. Open the rst retention cover.
Open the second bracket. Take out the
internal plastic cover.
Install CPU along with the carrier frame,
do not separate them. Please make sure the
carrier frame with CPU is closely attached
to the rail frame while inserting it.
Close the bracket that holds the CPU. Close
the retention cover and fasten the screw .
Install the Processor and Heatsink
Install the heatsink to the CPU carrier.
Secure the heastink to the CPU carrier
with a screwdriver.
9Install the PCIE Card
1Remove the bracket facing the slot that
you intend to use. Keep the screw for later
use.
2Align the card connector with the slot and
press rmly until the card is completely
seated on the slot.
Fasten the card to the chassis with the
screw.
3
IPMI LAN Port
ACT/LINK LED
SPEED LED
LAN Port
Activity / Link LED Speed LED
Status Description Status Description
O No Link O 10Mbps connection or no
link
Blinking Yellow Data Activity Yellow 100Mbps connection
On Link Green 1Gbps connection
10G LAN Port
Activity / Link LED Speed LED
Status Description Status Description
O No Link O 100Mbps connection or no
link
Blinking Green Data Activity Yellow 1Gbps connection
On Link Green 10Gbps connection
ACT/LINK LED
SPEED LED
LAN Port
7M.2 SSD Module Installation
8Install the Power Cables
ATX12V
4
8
1
5
12V
GND
ATX4PI N1
SATA P W R1
Micro-Fit Power Connector
1
N/A
GND
GND
+12V
GND +12V
+5V
N/A
24pin-to-4pin
Converter Cable
12
34
ATX_PWROK
PSON#
GND
ATX_+5VSB
Prepare a M.2 SSD module and the screw.
3
2
4
BCD A
1
BCD A
3
Depending on the PCB type and length of your
M.2 SSD module, nd the corresponding nut
location to be used.
Move the stando based on the module type
and length. e stando is placed at the nut
location D by default. Skip Step 3 and 4 and
go straight to Step 5 if you are going to use the
default nut.
Otherwise, release the stando by hand.
Peel o the yellow protective lm on the nut
to be used. Hand tighten the stando into the
desired nut location on the motherboard.
Align and gently insert the M.2 SSD module
into the M.2 slot. Please be aware that the M.2
SSD module only ts in one orientation.
Tighten the screw with a screwdriver to
secure the module into place. Please do not
overtighten the screw as this might damage the
module.
5
6
NUT1NUT2
D
No. 1 2 3 4
Nut Location A B C D
PCB Length 3cm 4.2cm 6cm 8cm
Module Type Type 2230 Type 2242 Ty pe 2260 Ty pe 228 0
BCD A
20o
BCD A
BCD A
1
2
3
4
1
2
3
4
5
Install the carrier frame with CPU. Don’t separate them.
Please mak e sure that the carrier
frame with CPU is closely attached to
the rail fra me while inser ting it.
Carrier Fram e with CPU
Rail Frame
6
7
8
9
10-5
10-3 10-1
10-6
10-4
10-2
10
Set your torque wrench to 1.54 in-lb.
One fourth a turn each time.
Tighten the screws in a sequential order
1 > 2 > 3 > 4 > 5 > 6.
Loosen the screws in a reverse order.
-
1
-
2
ASRock Rack GENOAD8UD-2T/X550 Installation guide
- Category
- Motherboards
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
ASRock Rack GENOAD8X-2T/BCM Installation guide
-
-
-
-
-
-
-
-
-