ASRock Rack SP2C741D32TM3 User manual

SP2C741D32TM3

User Manual

Version 1.0

Published May 2023

Version 1.0

Published June 2023

Copyright Notice:

No part of this documentation may be reproduced, transcribed, transmitted, or translated

in any language, in any form or by any means, except duplication of documentation by the

purchaser for backup purpose, without written consent of ASRock Rack Inc.

Products and corporate names appearing in this documentation may or may not be

registered trademarks or copyrights of their respective companies, and are used only for

identication or explanation and to the owners’ benet, without intent to infringe.

Disclaimer:

Specifications and information contained in this documentation are furnished for

informational use only and subject to change wit hout notice, and should not be

constructed as a commitment by ASRock Rack. ASRock Rack assumes no responsibility

for any errors or omissions that may appear in this documentation.

With respect to the contents of this documentation, ASRock Rack does not provide

warranty of any kind, either expressed or implied, including but not limited to the implied

warranties or conditions of merchantability or tness for a particular purpose.

In no event shall ASRock Rack, its directors, ocers, employees, or agents be liable for

any indirect, special, incidental, or consequential damages (including damages for loss of

prots, loss of business, loss of data, interruption of business and the like), even if ASRock

Rack has been advised of the possibility of such damages arising from any defect or error

in the documentation or product.

is device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

is equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. ese limits are designed to provide reason-

able protection against harmful interference in a residential installation. is equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in ac-

cordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment o and on, the user is encouraged to try to

correct the interference by one or more of the following

measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit dierent from that to which the

receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

INTEL END USER SOFTWARE LICENSE AGREEMENT

IMPORTANT - READ BEFORE COPYING, INSTALLING OR USING.

LICENSE. Licensee has a license under Intel’s copyrights to reproduce Intel’s Software

only in its unmodified and binary form, (with the accompanying documentation, the

“Soware”) for Licensee’s personal use only, and not commercial use, in connection with

Intel-based products for which the Soware has been provided, subject to the following

conditions:

(a) Licensee may not disclose, distribute or transfer any part of the Soware, and You agree

to prevent unauthorized copying of the Soware.

(b) Licensee may not reverse engineer, decompile, or disassemble the Soware.

(c) Licensee may not sublicense the Soware.

(d) e Soware may contain the soware and other intellectual property of third party

suppliers, some of which may be identied in, and licensed in accordance with, an enclosed

license.txt le or other text or le.

(e) Intel has no obligation to provide any support, technical assistance or updates for the

Soware.

OWNERSHIP OF SOFTWARE AND COPYRIGHTS. Title to all copies of the Soware

remains with Intel or its licensors or suppliers. e Soware is copyrighted and protected

by the laws of the United States and other countries, and international treaty provisions.

Licensee may not remove any copyright notices from the Soware. Except as otherwise ex-

pressly provided above, Intel grants no express or implied right under Intel patents, copy-

rights, trademarks, or other intellectual property rights. Transfer of the license terminates

Licensee’s right to use the Soware.

DISCLAIMER OF WARRANTY. e Soware is provided “AS IS” without warranty of

any kind, EITHER EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION,

WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PUR-

POSE.

LIMITATION OF LIABILITY. NEITHER INTEL NOR ITS LICENSORS OR SUPPLIERS

WILL BE LIABLE FOR ANY LOSS OF PROFITS, LOSS OF USE, INTERRUPTION OF

BUSINESS, OR INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAG-

ES OF ANY KIND WHETHER UNDER THIS AGREEMENT OR OTHERWISE, EVEN

IF INTEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

LICENSE TO USE COMMENTS AND SUGGESTIONS. is Agreement does NOT ob-

ligate Licensee to provide Intel with comments or suggestions regarding the Software.

However, if Licensee provides Intel with comments or suggestions for the modication,

correction, improvement or enhancement of (a) the Soware or (b) Intel products or pro-

cesses that work with the Soware, Licensee grants to Intel a non-exclusive, worldwide,

perpetual, irrevocable, transferable, royalty-free license, with the right to sublicense, under

Licensee’s intellectual property rights, to incorporate or otherwise utilize those comments

and suggestions.

TERMINATION OF THIS LICENSE. Intel or the sublicensor may terminate this license

at any time if Licensee is in breach of any of its terms or conditions. Upon termination,

Licensee will immediately destroy or return to Intel all copies of the Soware.

THIRD PARTY BENEFICIARY. Intel is an intended beneciary of the End User License

Agreement and has the right to enforce all of its terms.

U.S. GOVERNMENT RESTRICTED RIGHTS. The Software is a commercial item (as

dened in 48 C.F.R. 2.101) consisting of commercial computer soware and commercial

computer soware documentation (as those terms are used in 48 C.F.R. 12.212), consistent

with 48 C.F.R. 12.212 and 48 C.F.R 227.7202-1 through 227.7202-4. You will not provide

the Soware to the U.S. Government. Contractor or Manufacturer is Intel Corporation,

2200 Mission College Blvd., Santa Clara, CA 95054.

EXPORT LAWS. Licensee agrees that neither Licensee nor Licensee’s subsidiaries will

export/re-export the Software, directly or indirectly, to any country for which the U.S.

Department of Commerce or any other agency or department of the U.S. Government or

the foreign government from where it is shipping requires an export license, or other gov-

ernmental approval, without rst obtaining any such required license or approval. In the

event the Soware is exported from the U.S.A. or re-exported from a foreign destination

by Licensee, Licensee will ensure that the distribution and export/re-export or import of

the Soware complies with all laws, regulations, orders, or other restrictions of the U.S.

Export Administration Regulations and the appropriate foreign government.

APPLICABLE LAWS. is Agreement and any dispute arising out of or relating to it will

be governed by the laws of the U.S.A. and Delaware, without regard to conflict of laws

principles. e Parties to this Agreement exclude the application of the United Nations

Convention on Contracts for the International Sale of Goods (1980). e state and federal

courts sitting in Delaware, U.S.A. will have exclusive jurisdiction over any dispute arising

out of or relating to this Agreement. e Parties consent to personal jurisdiction and venue

in those courts. A Party that obtains a judgment against the other Party in the courts iden-

tied in this section may enforce that judgment in any court that has jurisdiction over the

Parties.

Licensee’s specic rights may vary from country to country.

WARNING

THIS PRODUCT CONTAINS A BUTTOON BATTERY

If swallowed, a button battery can cause serious injury or death.

Please keep batteries out of sight or reach of children.

CALIFORNIA, USA ONLY

e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance

controlled in Perchlorate Best Management Practices (BMP) regulations passed by the

California Legislature. When you discard the Lithium battery in California, USA, please

follow the related regulations in advance.

“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/

perchlorate”

AUSTRALIA ONLY

Our goods come with guarantees that cannot be excluded under the Australian Consumer

Law. You are entitled to a replacement or refund for a major failure and compensation for

any other reasonably foreseeable loss or damage caused by our goods. You are also entitled

to have the goods repaired or replaced if the goods fail to be of acceptable quality and the

failure does not amount to a major failure. If you require assistance please call ASRock

Rack Tel : +886-2-55599600 ext.123 (Standard International call charges apply)

ASRock Rack INC. hereby declares that this device is in compliance with the essential re-

quirements and other relevant provisions of related UKCA Directives. Full text of UKCA

declaration of conformity is available at: http://www.asrockrack.com

ASRock Rack INC. hereby declares that this device is in compliance with the essential re-

quirements and other relevant provisions of related Directives. Full text of EU declaration

of conformity is available at: http://www.asrockrack.com

ASRock Rack follows the green design concept to design and manufacture our products,

and makes sure that each stage of the product life cycle of ASRock Rack product is in line

with global environmental regulations. In addition, ASRock Rack disclose the relevant in-

formation based on regulation requirements.

Please refer to https://www.asrockrack.com/general/about.asp?cat=Responsibility for in-

formation disclosure based on regulation requirements ASRock Rack is complied with:

DO NOT throw the motherboard in municipal waste. is product has been

designed to enable proper reuse of parts and recycling. This symbol of the

crossed out wheeled bin indicates that the product (electrical and electronic

equipment) should not be placed in municipal waste. Check local regulations

for disposal of electronic products.

Contents

Chapter 1 Introduction 1

1.1 Package Contents 1

1.2 Specications 2

1.3 Unique Features 5

1.4 Motherboard Layout 6

1.5 Onboard LED Indicators 10

1.6 I/O Panel 12

1.7 Block Diagram 13

Chapter 2 Installation 14

2.1 Screw Holes 14

2.2 Pre-installation Precautions 14

2.3 Installing the CPU and Heatsink 15

2.4 Installation of Memory Modules (DIMM) 21

2.4.1 Mixing of DIMM Types 21

2.4.2 DIMM Population for DDR5 22

2.4.3 DIMM Population for DDR5 and CPS 25

2.5 Expansion Slots (PCI Express Slots) 29

2.6 Jumper Setup 30

2.7 Onboard Headers and Connectors 31

2.8 Unit Identication purpose LED/Switch 52

2.9 Dr. Debug 53

2.10 M.2 SSD Module Installation Guide 59

Chapter 3 UEFI Setup Utility 61

3.1 Introduction 61

3.1.1 UEFI Menu Bar 61

3.1.2 Navigation Keys 62

3.2 Main Screen 63

3.2.1 Motherboard Information 64

3.2.2 Processor Information 64

3.2.3 Memory Information 65

3.3 Advanced Screen 66

3.3.1 CPU Conguration 67

3.3.2 Platform Power Conguration 69

3.3.3 DRAM Conguration 72

3.3.4 Chipset Conguration 74

3.3.5 Storage Conguration 77

3.3.6 NVMe Conguration 78

3.3.7 ACPI Conguration 79

3.3.8 USB Conguration 80

3.3.9 Super IO Conguration 81

3.3.10 Serial Port Console Redirection 82

3.3.11 H/W Monitor 85

3.3.12 Runtime Error Logging 86

3.3.13 Intel SPS Conguration 88

3.3.14 Network Stack Conguration 89

3.3.15 Intel VMD technology 90

3.3.16 Tls Auth Conguration 91

3.3.17 Instant Flash 92

3.4 Server Mgmt 93

3.4.1 BMC Network Conguration 95

3.4.2 System Event Log 97

3.4.3 BMC Tools 98

3.5 Security 99

3.5.1 Key Management 100

3.6 Event Logs 104

3.7 Boot Screen 105

3.8 Exit Screen 107

Chapter 4 Software Support 108

4.1 Download and Install Operating System 108

4.2 Download and Install Software Drivers 108

4.3 Contact Information 108

Chapter 5 Troubleshooting 109

5.1 Troubleshooting Procedures 109

5.2 Technical Support Procedures 111

5.3 Returning Merchandise for Service 111

SP2C741D32TM3

PB 1

English

Chapter 1 Introduction

Thank you for purchasing ASRock Rack SP2C741D32TM3 motherboard, a reliable

motherboard produced under ASRock Rack’s consistently stringent quality control. It delivers

excellent performance with robust design conforming to ASRock Rack’s commitment to

quality and endurance.

In this manual, chapter 1 and 2 contains introduction of the motherboard and step-by-step

guide to the hardware installation. Chapter 3 and 4 contains the conguration guide to BIOS

setup and information of the soware support.

1.1 Package Contents

• ASRock Rack SP2C741D32TM3 Motherboard

(Proprietary Form Factor: 18.87-in x 16.85-in)

• Quick Installation Guide

• 2 x Screws for M.2 Sockets

• 4 x CPU Non-Fabric Carriers

If any items are missing or appear damaged, contact the authorized dealer.

Because the motherboard specications and the BIOS soware might be updated, the con-

tent of this manual will be subject to change without notice. In case any modications of

this manual occur, the updated version will be available on ASRock Rack website without

further notice. Find the latest memory and CPU support lists on ASRock Rack website as

well. ASRock Rack’s Website: www.ASRockRack.com

Please visit the website for more information about the using model.

http://www.asrockrack.com/support/

2 3

English

1.2 Specications

SP2C741D32TM3

Physical Status

Form Factor Proprietary

Dimension 18.87" x 16.85" (479.30 x 427.99mm)

Processor System

CPU Supports 4th Gen Intel® Xeon® Scalable processors, codenamed

Sapphire Rapids

Socket 1+1 Socket E (LGA 4677)

ermal Design

Power (TDP)

~350W

Chipset Emmitsburg chipset (Intel® C741)

System Memory

Supported DIMM

Quantity

16+16 DIMM slots (2DPC)

Supported Type 288-pin DDR5 RDIMM/RDIMM-3DS

Max. Capacity per

DIMM

RDIMM: 64GB

RDIMM-3DS: 2H- 128 GB/ 4H- 256 GB

Max. Frequency 4400 MT/s (2DPC) / 4800 MT/s (1DPC)

Voltage 1.1V

Note Memory support is to be validated

PCIe Expansion Slots

SLOT1 Gen Z 4C (PCIe5.0 / CXL1.1 x16) [CPU1]

SLOT2 Gen Z 4C (PCIe5.0 / CXL1.1 x16) [CPU2]

Other PCIe Expansion Connectors

M.2 slot 2 M-key (PCIe4.0 x4), supports 22110/2280 form factor [CPU2]

MCIO 6 MCIO (PCIe5.0 x8) [CPU2]

6 MCIO (PCIe5.0 x8) [CPU1]

SATA/SAS Storage

PCH Built-in

Storage

Emmitsburg chipset (Intel® C741) (8 SATA 6Gb/s, support

RAID 0/1/5/10):

1 Slimline

Ethernet

OCP Slot 1 OCP NIC 3.0 (PCIe5.0 x16) [CPU2]

1 OCP NIC 3.0 (PCIe5.0 x16) [CPU1]

USB

Controller/Hub Emmitsburg chipset Intel® C741

Connectors/

Headers

External:

2 Type-A (USB3.2 Gen1)

Internal:

1 header (26-pin, 1 USB3.1 Gen1, 2 USB2.0)

1 header (19-pin, 2 USB3.1 Gen1)

SP2C741D32TM3

2 3

English

Graphics

Controller ASPEED AST2600:

1 Mini-DP (not support DP++), 1 header (VGA)

Security

TPM 1 (13-pin, SPI)

Rear I/O

UID Button/LED 1 UID button w/ LED

Video Output 1 Mini-DP (DP/Mini_DP)

USB 2 Type-A (USB3.2 Gen1)

RJ45 1 RJ45 (COM), 1 dedicated IPMI

Hardware Monitor

Temperature CPU, PCH, MB, Card Side Temperature Sensing

Fan Fan Tachometer

CPU Quiet Fan (Allow Chassis Fan Speed Auto-Adjust by

CPU Temperature)

Fan Multi-Speed Control

Voltage 1.05V_PCH, 1.8V_PCH, +BAT, PVNN_PCH, 3.3V, 5V, 12V,

3.3VSB, 5VSB, 12V, +12VSB

Server Management

BMC Controller ASPEED AST2600: IPMI2.0 with iKVM and vMedia support

IPMI Dedicated

GLAN

1 RJ45 Dedicated IPMI LAN port by Realtek RTL8211F

System BIOS

BIOS Ty pe AMI UEFI BIOS; 512Mb SPI Flash ROM

Features Plug and Play, ACPI 4.0 and above compliance wake up events,

SMBIOS 3.4 and above , ASRock Rack Instant Flash

Internal Connectors/Headers

PSU Connector 2 (CRPS IN +12V/+12VSB, max. 2700W )

Other Power

Connectors

4 (2x4 pin, 12V) for PCIe cards, 2 (2x3 pin, 12V) for HSBP, 2

(2x3 pin,3.3VSB,3.3V,12V) for MCIO

Auxiliary Panel

Header

1 (18-pin): chassis intrusion, system fault LED, locate, SMBus

System Panel

Header

1 (26-pin): System fault LED, locate, SMBus, power switch,

reset switch, system power LED

NMI Header 1

VGA Header 1 (15-pin)

Fan Header 8 (4pin) for 2U system, 8 (6pin) for 1U system

TPM Header 1 (13-pin, SPI)

VROC Header 1

HSBP 2

SMbus Header 1

Speaker 1

Clear CMOS 1 (contact pads)

4 5

English

LED Indicators

Standby Power

LED

1

80 Debug Port LED 1

Fan Fail LED 8

BMC Heartbeat

LED

1

Support OS

OS Microso® Windows®

- Server 2022(64 bit)

Linux®

- Red Hat Enterprise Linux Server 8.4(64bit) / 8.5(64bit) /

9.1(64bit)

- SUSE Enterprise Linux Server 15 SP3(64bit)

- Ubuntu 21.10(64bit), 22.04(64bit)

Hypervisor

- VMWare® ESXi 7.0 U3g / 8.0

* On the Ubuntu system is not support Raid mode.

* Please refer to our website for the latest OS support list.

Enviroment

Operating

temperature

10 - 35°C (50 - 95 degF)

Non-operating

temperature

-40 - 70°C (-40 - 158degF)

NOTE: Please refer to the website for the latest specications.

If installing Intel® LAN utility or Marvell SATA utility, this motherboard may fail Win-

dows® Hardware Quality Lab (WHQL) certication tests. If installing the drivers only, it

will pass the WHQL tests.

SP2C741D32TM3

4 5

English

1.3 Unique Features

ASRock Rack Instant Flash is a BIOS ash utility embedded in Flash ROM. is convenient

BIOS update tool allows user to update system BIOS without entering operating systems

rst like MS-DOS or Windows®. With this utility, press the <F6> key during the POST or the

<F2> key to enter into the BIOS setup menu to access ASRock Rack Instant Flash. Just launch

this tool and save the new BIOS le to the USB ash drive, oppy disk or hard drive, then

update the BIOS only in a few clicks without preparing an additional oppy diskette or other

complicated ash utility. Please be noted that the USB ash drive or hard drive must use

FAT32/16/12 le system.

6 7

English

1.4 Motherboard Layout

FRNT_VGA1

47.93 cm (18.87 in)

42.8 cm (16.85 in)

M2_1

BAT1

SP2C741D32TM3

UID1

LAN1

USB3.2

Gen1 Ports

T: USB3_2

B: USB3_1

BMC_SMB1

ME_RECOVERY1

PASSWORD_CLEAR1BIOS_SWAP_OVERRIDE1

CPU2_HSBP1

DDR5_O2

DDR5_O1

DDR5_P2

DDR5_P1

DDR5_M2

DDR5_M1

DDR5_N2

DDR5_N1

DDR5_L1

DDR5_L2

DDR5_K1

DDR5_K2

CPU2

FAN2_1

OCP1

PCIE1

BIOS

ROM

BMC

ROM

Dr. Debug

ASPEED

AST2600

PCIE2

NUT2

NUT4

Intel C741

DDR5_J1

DDR5_J2

DDR5_I1

DDR5_I2

MCIO2 MCIO1

USB3_2

M2_2

SPEAKER1

FLASH_SEC_OVERRIDE1

NMI_BTN1CASEOPEN1

OCP2

COM1

MINI_DP

NUT1

NUT3

SATA_0

CPU1

MCIO12

MCIO11

CPU1_HSBP1

RAID_1

TPM_BIOS_PH1

PSU_CON2 PSU_CON1

MCIO9

MCIO10

MCIO_PWR1

HDD_PWR1

USB3_1

GPU_PWR1 GPU_PWR2

FAN8_1

FAN1_1

FAN1

FAN2

HSBP_PWR2

FAN3

FAN3_1

FAN4_1

MCIO4 MCIO3MCIO6 MCIO5

FAN5_1

HSBP_PWR1

MCIO8 MCIO7

FAN5

FAN6

FAN7

FAN6_1

FAN7_1

GPU_PWR3

AUX_PANEL2

GPU_PWR4

PANEL1

PWM_CFG2

AUX_PANEL1

MCIO_PWR2

HDD_PWR2

PWM_CFG1

DDR5_B1

DDR5_B2

DDR5_A1

DDR5_A2

DDR5_D1

DDR5_D2

DDR5_C1

DDR5_C2

DDR5_G2

DDR5_G1

DDR5_H2

DDR5_H1

DDR5_E2

DDR5_E1

DDR5_F2

DDR5_F1

CLRMOS1

FAN4

FAN8

16

14 15 17

8 10 11

91213 1819 20 21 22 23

24

25

26

27

28

29

31

32

33

34

35

36

37

38

39

50

51

53

123 5

6

7

4

54

55

56

57

58

59

40

41

42

43

46

47

48

49

44

45

60

61

62

63

64

65666768

69

707172737475767778

79808182838485

86

30

52

SP2C741D32TM3

6 7

English

No. Description

1 Non Maskable Interrupt Button (NMI_BTN1)

2 Flash Override Jumper (FLASH_SEC_OVERRIDE1)

3 Chassis Intrusion Header (CASEOPEN1)

4TPM-SPI Header (TPM_BIOS_PH1)

5 OCP 3.0 Gen5 x16 Mezzanine Card Slot (OCP2)

6 M.2 Socket (M2_1) (Type 2280/22110)

7 M.2 Socket (M2_2) (Type 2280/22110)

8 Backplane PCI Express Hot-Plug Connector (CPU1_HSBP1)

9 Front VGA Header (FRNT_VGA1)

10 Backplane PCI Express Hot-Plug Connector (CPU2_HSBP1)

11 PSU Power Connector (PSU_CON2)

12 Mini Cool Edge IO Connector (MCIO11)

13 Mini Cool Edge IO Power Connector (MCIO_PWR2)

14 Auxiliary Panel Header (AUX_PANEL1)

15 HDD Power Connector (HDD_PWR2)

16 Mini Cool Edge IO Connector (MCIO12)

17 PCI Express 5.0 x16 Slot (PCIE2)

18 2 x 288-pin DDR5 DIMM Slots (DDR5_K1, DDR5_L1)*

19 2 x 288-pin DDR5 DIMM Slots (DDR5_K2, DDR5_L2)*

20 System Panel Header (PANEL1)

21 GPU Power Connector (GPU_PWR4)

22 Auxiliary Panel Header (AUX_PANEL2)

23 GPU Power Connector (GPU_PWR3)

24 Mini Cool Edge IO Connector (MCIO8)

25 System Fan Connector (FAN7_1) (for 1U system)

26 2 x 288-pin DDR5 DIMM Slots (DDR5_I1, DDR5_J1)*

27 Mini Cool Edge IO Connector (MCIO7)

28 System Fan Connector (FAN6_1) (for 1U system)

29 System Fan Connector (FAN8) (for 2U system)

30 System Fan Connector (FAN7) (for 2U system)

31 2 x 288-pin DDR5 DIMM Slots (DDR5_I2, DDR5_J2)*

32 PWM Conguration Header (PWM_CFG2)

33 HDD Backplane Power Connector (HSBP_PWR1)

34 LGA 4677 CPU Socket (CPU2)

8 9

English

No. Description

35 2 x 288-pin DDR5 DIMM Slots (DDR5_M2, DDR5_N2)*

36 System Fan Connector (FAN6) (for 2U system)

37 System Fan Connector (FAN5) (for 2U system)

38 Mini Cool Edge IO Connector (MCIO6)

39 2 x 288-pin DDR5 DIMM Slots (DDR5_M1, DDR5_N1)*

40 System Fan Connector (FAN5_1) (for 1U system)

41 2 x 288-pin DDR5 DIMM Slots (DDR5_O2, DDR5_P2)*

42 Mini Cool Edge IO Connector (MCIO5)

43 2 x 288-pin DDR5 DIMM Slots (DDR5_O1, DDR5_P1)*

44 System Fan Connector (FAN4_1) (for 1U system)

45 System Fan Connector (FAN3_1) (for 1U system)

46 2 x 288-pin DDR5 DIMM Slots (DDR5_C1, DDR5_D1)*

47 Mini Cool Edge IO Connector (MCIO4)

48 2 x 288-pin DDR5 DIMM Slots (DDR5_C2, DDR5_D2)*

49 System Fan Connector (FAN2_1) (for 1U system)

50 2 x 288-pin DDR5 DIMM Slots (DDR5_A1, DDR5_B1)*

51 Mini Cool Edge IO Connector (MCIO3)

52 System Fan Connector (FAN4) (for 2U system)

53 System Fan Connector (FAN3) (for 2U system)

54 2 x 288-pin DDR5 DIMM Slots (DDR5_A2, DDR5_B2)*

55 PWM Conguration Header (PWM_CFG1)

56 HDD Backplane Power Connector (HSBP_PWR2)

57 LGA 4677 CPU Socket (CPU1)

58 2 x 288-pin DDR5 DIMM Slots (DDR5_E2, DDR5_F2)*

59 System Fan Connector (FAN2) (for 2U system)

60 System Fan Connector (FAN1) (for 2U system)

61 Mini Cool Edge IO Connector (MCIO2)

62 2 x 288-pin DDR5 DIMM Slots (DDR5_E1, DDR5_F1)*

63 System Fan Connector (FAN1_1) (for 1U system)

64 Mini Cool Edge IO Connector (MCIO1)

65 GPU Power Connector (GPU_PWR2)

66 System Fan Connector (FAN8_1) (for 1U system)

67 GPU Power Connector (GPU_PWR1)

68 2 x 288-pin DDR5 DIMM Slots (DDR5_G2, DDR5_H2)*

SP2C741D32TM3

8 9

English

No. Description

69 2 x 288-pin DDR5 DIMM Slots (DDR5_G1, DDR5_H1)*

70 PCI Express 5.0 x16 Slot (PCIE1)

71 Mini Cool Edge IO Connector (MCIO9)

72 Mini Cool Edge IO Power Connector (MCIO_PWR1)

73 Front USB 3.2 Gen1 Header (USB3_1)

74 HDD Power Connector (HDD_PWR1)

75 Front USB 3.2 Gen1 Header (USB3_2)

76 PSU Power Connector (PSU_CON1)

77 BMC SMBus Header (BMC_SMB1)

78 Mini Cool Edge IO Connector (MCIO10)

79 SATA Connector (SATA_0)

80 Clear CMOS Pad (CLRMOS1)

81 OCP 3.0 Gen5 x16 Mezzanine Card Slot (OCP1)

82 ME Recovery Jumper (ME_RECOVERY1)

83 Password Reset Jumper (PASSWORD_CLEAR1)

84 Virtual RAID On CPU Header (RAID_1)

85 BIOS Swap Override Jumper (BIOS_SWAP_OVERRIDE1)

86 Speaker Header (SPEAKER1)

*For DIMM installation and conguration instructions, please see p.21 (Installation of Memory Modules

(DIMM)) for more details.

10 11

English

1.5 Onboard LED Indicators

9

8

7

6

5

4

3

2

1

1011

12

13

SP2C741D32TM3

10 11

English

No. Item Status Description

1LED_ SYS_FAULT Red System failed

2LED_FAN7 Red FAN7 failed

3LED_FAN6 Red FAN6 failed

4LED_FAN5 Red FAN5 failed

5LED_FAN4 Red FAN4 failed

6LED_FAN3 Red FAN3 failed

7LED_FAN2 Red FAN2 failed

8LED_FAN1 Red FAN1 failed

9LED_FAN8 Red FAN8 failed

10 LED_CATERR1 Red CPU CATERR failed

11 PLD_HB2 Green FPGA heartbeat LED

12 SB_PWR1 Green STB PWR ready

13 BLED1 Green BMC heartbeat LED

12 13

English

1.6 I/O Panel

No. Description No. Description

1 Mini Display Port (MINI_DP) 4 LAN RJ-45 Port (IPMI_LAN)*

2 USB 3.2 Gen1 Ports (USB3_1_2) 5 UID Switch (UID1)

3 RJ45 Serial Port (COM1)

LAN Port LED Indications

*ere is an LED on each side of IPMI LAN port. Please refer to the table below for the

LAN port LED indications.

IPMI LAN Port LED Indications

Activity / Link LED Speed LED

Status Description Status Description

O No Link O 10Mbps connection or no

link

Blinking Yellow Data Activity Orange 100Mbps connection

On Link Green 1Gbps connection

ACT/LINK LED

SPEED LED

LAN Port

4

3

125

Page is loading ...

ASRock Rack SP2C741D32TM3 User manual

ASRock Rack SP2C741D32TM3 User manual

Related papers

Other documents