ADD Offroad R951271280103 Installation guide

Category
Fitness, gymnastics & weight training
Type
Installation guide

ADD Offroad R951271280103 is a rear bumper designed for 2007-2018 Jeep Wrangler JK. It's made of high-quality materials and provides increased protection for the rear of your vehicle. The bumper features integrated mounting points for cube lights, allowing you to enhance your visibility and safety while driving in low-light conditions. Installation requires some mechanical skills and an estimated 2 hours for bumper installation and an additional hour for wiring cube lights. Ensure proper torque of mounting bolts for optimal performance and safety.

ADD Offroad R951271280103 is a rear bumper designed for 2007-2018 Jeep Wrangler JK. It's made of high-quality materials and provides increased protection for the rear of your vehicle. The bumper features integrated mounting points for cube lights, allowing you to enhance your visibility and safety while driving in low-light conditions. Installation requires some mechanical skills and an estimated 2 hours for bumper installation and an additional hour for wiring cube lights. Ensure proper torque of mounting bolts for optimal performance and safety.

2007-2018 Jeep Wrangler JK Stealth Fighter™
Rear Bumper Installation Instructions
Addictive Desert Designs® | Page 1
ADDICTIVE DESERT DESIGNS®
®
Preparation:
• Disconnect the negative battery terminal. Park the vehicle on level ground and set the emergency brake.
• We recommend reading through the installation instructions in whole before performing the work.
• Estimated Installation Time: 2 Hours for OEM Removal/Bumper Installation
1 Additional Hour to Wire Cube Lights
**is installation requires 2 people for best results**
**Labor Rates are based on a vehicle with no pre-existing damage. Wiring labor is based on a standard wiring procedure
with light switches installed in an easily accessible location. Custom light triggering or switch mounting location will
result in a greater labor charge.**
You will need the following tools:
- Ratchet - 3/4" Socket & Wrench - 16mm Socket
- 17mm Socket - 18mm Socket
Included in Kit:
4 - Hex Head Bolts
(M10-1.5 x 30mm)
4 - Flat Washers
(M10)
2 - Hex Head Bolts
(1/2"-20 x 4 1/2")
4 - Flat Washers
(1/2")
2 - Metal Lock Nuts
(1/2"-20)
2007-2018 Jeep Wrangler JK Stealth Fighter™
Rear Bumper Installation Instructions
Addictive Desert Designs® | Page 2
ADDICTIVE DESERT DESIGNS®
®
Removal:
1. Use a 16mm Socket to remove the two bolts per side that hold the bumper to the side of the Jeep's frame. (Fig
A) was taken looking towards the rear of the vehicle into the wheel well.
Fig A
2. Use a 16mm Socket to remove the two bolts on the back side of the rear bumper. ese bolts are above the
rear frame rail. ere are not visible in the following picture, but are just above the bolts that are visible in the
picture. (Fig B)
Remove the bolt that
sits just above the
frame rail (Cannot be
seen in the picture)
Fig B
2007-2018 Jeep Wrangler JK Stealth Fighter™
Rear Bumper Installation Instructions
Addictive Desert Designs® | Page 3
ADDICTIVE DESERT DESIGNS®
®
3. Li the OEM bumper o the vehicle.
4. Using an 18mm Socket, remove the three bolts that hold on the rear tow hook. en, remove the tow hook.
(Fig C)
Fig C
2007-2018 Jeep Wrangler JK Stealth Fighter™
Rear Bumper Installation Instructions
Addictive Desert Designs® | Page 4
ADDICTIVE DESERT DESIGNS®
®
Installation:
5. If you have lights to install in your bumper, now is a good time to do so. Please follow the light manufactur-
er's install guide for mounting/wiring information.
6. Set the bumper in place on the vehicle. en, use the supplied M10 Bolts (x4) and M10 Washers (x4) into the
side mounting holes on the bumper. Leave these bolts loose for now. (Fig D)
Fig D
7. Install the supplied 1/2" x 4 1/2" Bolts (x2), 1/2" Washers (x4), and 1/2" Lock Nuts (x2) into the lower bumper
mounting holes. (Fig E)
Fig E
2007-2018 Jeep Wrangler JK Stealth Fighter™
Rear Bumper Installation Instructions
Addictive Desert Designs® | Page 5
ADDICTIVE DESERT DESIGNS®
®
For Additional Support or Technical Questions,
Please Call 480-671-0820 or
is product is protected by one or more U.S. patents
www.addictivedesertdesigns.com/patents
8. Align the bumper so it is straight in relation to the tailgate. en, torque the M10 mounting bolts to 40 foot
pounds. Torque the 1/2" mounting bolts to 80 foot pounds.
9. Stand back and enjoy your new ADD Stealth Fighter™ Rear Bumper.
10. Check and re-tighten, if needed, all mounting bolts aer 100 miles and periodically thereaer.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

ADD Offroad R951271280103 Installation guide

Category
Fitness, gymnastics & weight training
Type
Installation guide

ADD Offroad R951271280103 is a rear bumper designed for 2007-2018 Jeep Wrangler JK. It's made of high-quality materials and provides increased protection for the rear of your vehicle. The bumper features integrated mounting points for cube lights, allowing you to enhance your visibility and safety while driving in low-light conditions. Installation requires some mechanical skills and an estimated 2 hours for bumper installation and an additional hour for wiring cube lights. Ensure proper torque of mounting bolts for optimal performance and safety.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI