MOUNTUP MU0027 User manual

Brand: MOUNTUP

Model: MU0027

Category: Flat panel desk mounts

Type: User manual

Gaming Counterbalance Desk Mount

Instruction Manual

MA07-12-US3.0

1.5~8kg

(3.3~17.6lbs)

RATED

VESA Size

75x75 mm

100x100 mm

Screen Weight

If you have any questions, please feel free to contact Customer Service via Amazon before returning.

PRODUCT LINE GRAPH

WARNING!

300mm

75mm

100mm

115mm

75mm

100mm

115mm

189mm

7.4'' 8.19~11.06''

0.39~3.35''

7.36~19.17''

11.8''

0.39~3.35''

2.44''

4.53''

3.94''

2.95''

208~281mm 62mm

min10~max85mm

min187~max487mm

min10~max85mm

+90°

-45°

±90°

±180° ±180°

If you have any confusion or are not quite sure about the installation, please do not hesitate to ask for our help.

Before assembly, please check and make sure all necessary accessories are included and undamaged. Improper

installation, such as using the product for monitors over its load capacity or for any purpose not explicitly specied,

may cause damage or serious injury. We would not be liable for any damage or injury caused by improper

mounting or inappropriate use.

The kit contains small items that could be choking hazards if swallowed. Please keep them OUT OF REACH OF

CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED.

Components

Hardware

PACKAGE CONTENTS

A (x1)

Arm

C (x1)

Bracket

D (x1)

Clamp

F (x1)

Long Bolt

G (x1)

Grommet Base

I (x1)

Security Screw

H (x1)

Support Plate

J (x6)

Screw

K(x1)

Wingnut

L(x1)

Base

M(x1)

Washer

N(x1)

Calathiform Gasket

O(x1)

Bolt

P(x1)

4mm Allen Key

Q(x1)

5mm Allen Key

E(x1)

Bracket Cover

B (x1)

VESA Plate

R(x1)

6mm Allen Key

Note: Not all hardware included will be used.

M-C (x4)

Spacer H10mm

M-A (x4)

M4x12mm

M-B (x4)

M4x25mm

STEP 1 Mount the Base to Bottom of the Arm

STEP 2 Clamp Installation OR Grommet Base Installation

OPTION A: Clamp Installation

Mount bracket (C) to the bottom of arm (A) using screws(J). Tighten the screws with

supplied 4mm Allen key (P).

Mount the base(L) to the bottom of arm (A) using Washer(M), calathiform gasket(N) and Bolt(O).

Tighten (do not over tighten) the Bolt (O) securely with supplied 5mm Allen key (Q).

concave side of the

washer needs to be

faced to the Base (L)

You could also refer to the Video Guide about installation on our product page.

Warm Tips

Secure clamp (D) to upper two holes with

bolts (J) using 4mm Allen Key (P) for desks

with a thickness of 10-55mm.

Secure clamp (D) to lower two holes with

bolts (J) using 4mm Allen Key (P) for desks

with a thickness of 50-85mm.

Adjust the Mount to the Desktop

Thickness 10-55mm

Adjust the Mount to the Desktop

Thickness 50-85mm

Attach bracket cover (E)to bracket(C). Tighten the clamp to the desktop using the plastic knob

or by using 6mm Allen key (R).

10-55mm

0.39-2.17"

1.97-3.35"

50-85mm

STEP 2 (Continued)

OPTION B: Grommet Base Installation

For grommet hole mounting, place long bolt(F) through the center of grommet base (G).

Mount grommet base to the bottom of arm (A) using screws(J). Tighten the screws with

supplied 4mm Allen key (P).

Run long bolt(F) through grommet hole in desktop. Secure it by using the support plate (H)

and Wingnut (K). Tighten Wingnut.

DESK DESK

Please do not move stand outside desk for safety!

DESK

ø 10~60mm

ø 0.39~2.36"

STEP 3 Attach the monitor to the arm

Monitor Monitor Monitor

monitor monitormonitor

OPTION A: Flat Back Monitor

OPTION B: Curved Back Monitor

Attach the VESA plate (B) to the back of monitor

and secure it by using a 6 mm Allen Key (R) to

tighten screws (M-A).

Do not tighten the screws excessively or your monitor

might be damaged.

Attach the VESA plate (B) to the back of monitor

and secure it by using a 6 mm Allen Key (R) to

tighten screws (M-B) along with spacers (M-C).

Do not tighten the screws excessively or your monitor

might be damaged.

M-A

M-B

M-C

Slide the monitor onto the head of swivel arm(A), install the security screw (I). Make

sure the security screw is tightened before you rotate the monitor.

Refer to below illustrations to

adjust tilting angle of your monitor.

A A

Problem:

If monitor face down

Solution:

1. Loosen the tilting bolt.

2. Hold the bottom of monitor with

one hand and adjust to determine

your desired tilt angle.

3. Retighten the tilting bolt

towards " " to x the angle.

STEP 4 Adjust the tension

For proper functioning of this mount, depending on dierent weight of monitor you might need to adjust

tension spring in Arm (A) by using 6 mm Allen key (R).

Note:

It is normal for a bit noise when you adjust the spring tension.

After being attached to the arm, the monitor falls down

and can not stay at the desired height by itself.

Turn clockwise(“+”direction) to increase tension

until the monitor can stay at the desired Height by itself.

After being attached to the arm, the monitor rises up and

can not stay at the desired height by itself.

Turn counter-clockwise(“-”direction) to reduce tension until the

monitor can stay at the desired Height by itself.

WARNING

Please DO NOT loosen the screw.

For how many circles the screw should be turned, please refer to the table below.

Note2:

Circles (AT LEAST) 108643min 12

Monitor Weight 4.4lbs

(2kg) 6.6lbs

(3kg) 8.8lbs

(4kg) 11lbs

(5kg) 13.2lbs

(6kg) 15.4lbs

(7kg) 17.6lbs

(8kg)

STEP 5 Cable Management

Remove the bottom plastic covers from spring arm(A) as shown in diagram.

Run cables from monitor through the bottom of spring arm (A). Reattach plastic covers

as shown in diagram.

Adjust as Desired

Allen Key(P,Q) can be stored in Base Support Cover(E) for next time using.

+90°

-45°

±180°

±90°

±180°

Note: To ensure stability, the tightness of the rotating axis has been

preset, so it would be kind of dicult to rotate the VESA plate.

Suggestion: Please attach the monitor rst, then hold the two sides

of it with both hands, and rotate vigorously.

If that doesn't work out, please do not hesitate to ask for our help.

• Never allow children to climb, stand, hang, or play on any part of monitor or stand.

• This product is intended for indoor use only. Using this product outdoors could lead to

product failure and personal injury.

• Check that the bracket is secure and safe to use at regular intervals

(at least every three months).

CAUTION AND MAINTENANCE

MOUNTUP MU0027 User manual

Brand: MOUNTUP

Model: MU0027

Category: Flat panel desk mounts

Type: User manual

Download PDF

report

MOUNTUP MU0027 User manual

MOUNTUP MU0027 User manual

Related papers

Other documents