2. Spectrum Industries
  3. 38906KP

Spectrum Industries 38906KP, 38906CHB Assembly Instructions

  • Hello! I've reviewed the user manual for the Touchboards Corner Connector 38906. This document provides detailed assembly instructions including component attachment and full step-by-step guidelines for installing the connector between desks. I am ready to help with any questions you have about the assembly process or the included parts.
  • What tools are required for the assembly?
    How many 1/4-20 x 5/8" PHM screws are used to attach Flip-Top Support Brackets and Cord Channel?
    What do I do if parts are damaged during shipment?
Evolution Corner Connector
(30") #38906
Assembly Instructions:
1.
(2) 050524
#8 x 3/4" PH TEK
Screw
Tools Required:
Phillips Screwdriver
Electric Drill w/ Phillips Bit
4mm Hex Wrench (included)
(15) 026064
1/4-20 x 5/8 PHMS
(2) 036281
Dual Unit-to-Unit
Bracket
(2) 0102049
1/8" Steel 'Z' Bracket
(2) 021554
1/4-20 x 50mm
JC Bolt
(1) 025039
4mm Hex Wrench
A. Place corner connector upside-down.
B. A
ttac
h
t
h
e
t
w
o
Fli
p
-T
op
Suppo
r
t
Br
ac
k
ets
a
n
d
Co
r
d
C
h
a
nn
e
l wi
t
h
Before you begin, please make sure all parts and proper quantities are included. Any parts damaged during shipment must be
reported within 15 days of receipt. To report information regarding damages or if you have any questions, please call 1-800-235-
1262.
Attach Flip-Top Support Brackets and Cord Channel
(2) 026009
1/4-20 Locknut
(2) 036207
Flip-Top Support
Bracket
ttac t e t o p
op Suppo t ac ets a d Co d C a e t
(5) 1/4-20 x 5/8" PHM Screws as shown in Figure 1.
Flip-Top Brackets
Cord
Channel
1/4-20 x 5/8 PHMS
Figure 1
052525XR2 Pa
g
e 1 of 2
'Z' Bracket
A. Attach the 'Z' Brackets to the rear of each desk as shown in Figure 2 using (1) 1/4-20 x 50mm JC Bolt and
Locknut. Tighten completely. Note: The elongated hole on the 'Z' Bracket will attach to the Corner Connector.
C. Using an electric drill with a Phillips bit, install a #8 x 3/4" PH TEK Screw through the 'Z' Bracket and into the leg.
B. Attach the Dual Unit-to-Unit Brackets to the front of each desk as shown. Do not tighten completely.
Attach Brackets to Desks
2.
#8 x 3/4" PH TEK
Screw
Figure 2
1/4-20 x 50mm JC Bolt
1/4-20 Locknut
Front of Desk
Dual Unit-to-Unit
Bracket
1/4-20 x 5/8"
PHM Screw
Cord Channel
Leg
A. Align both desk 90° to each other leaving about 6" between the corners as shown in Figure 3.
B. Place the Corner Connector onto the brackets and align the mounting holes.
C. Install (6) 1/4-20 x 5/8" PHM Screws, but do not tighten completely-after the screws are started, alignment of the
desks may be necessary.
D. After alignment is satisfactory, tighten all screws.
Attach Corner Connector to Desks
3.
Figure 3
Corner
Connector
Evolution Desk Evolution Desk
052525XR2 Pa
g
e 2 of 2
/