GarrettCom Magnum 6KQ User manual

i

www GarrettCom com

..

www GarrettCom com

..

Corporate Headquarters

GarrettCom, Inc.

47823 Westinghouse Dr.

Fremont, CA 94539-7437

Phone (510) 438-9071

Fax (510) 438-9072

Website: http://www.GarrettCom.com

email support@garrettcom.com

Magnum 6KQ

Managed Field Switch

Hardware

Installation and User Guide

Magnum 6KQ Managed Field Switch Installation & User Guide 04/07)

i

www GarrettCom com

..

Magnum

6KQ

Managed Field Switch

Hardware

Installation and User Guide

Part #: 84-00180Z (Rev. A)

Trademarks

Ethernet is a trademark of Xerox Corporation

NEBS is a trademark of Telcordia Technologies

UL is a registered trademark of Underwriters Laboratories

GarrettCom, Magnum and Personal Switch are trademarks and Personal Hub is a

registered trademark of GarrettCom, Inc.

Important: The Magnum 6KQ Managed Field Switch contains no user

serviceable parts. Attempted service by unauthorized personnel shall render all

warranties null and void. If problems are experienced with Magnum 6KQ

Switch products, consult Section 6, Troubleshooting, of this User Guide.

of this publication may be reproduced without prior written permission from

GarrettCom, Inc.

Printed in the United States of America.

Magnum 6KQ Managed Field Switch Installation & User Guide 04/07)

ii

www GarrettCom com

..

Contacting GarrettCom, Inc

Please use the mailing address, phone and fax numbers and email address listed below:

GarrettCom, Inc.

47823 Westinghouse Dr.

Fremont, CA 94539-7437

Phone (510) 438-9071

Fax (510) 438-9072

Website: http://www.GarrettCom.com

email [email protected]

Federal Communications Commission

Radio Frequency Interference Statement

This equipment generates, uses and can radiate frequency energy and if not

installed and used properly, that is in strict accordance with the manufacturer's

instructions, may cause interference to radio communication. It has been tested and

found to comply with the limits for a Class A computing device in accordance with the

specifications in Subpart J of Part 15 of FCC rules, which are designed to provide

reasonable protection against such interference when operated in a commercial

environment. Operation of this equipment in a residential area is likely to cause

interference, in which case the user at his own expense will be required to take whatever

measures may be required to correct the interference.

Canadian Emission

This Class A digital apparatus meets all requirements of the Canadian

Interference-Causing Equipment Regulations.

Cet appareil respecte toutes les exigences du Réglement sur le matériel du

Canada. Cet appareil est Classe A..

Magnum 6KQ Managed Field Switch Installation & User Guide 04/07)

iii

www GarrettCom com

..

Table of Contents.............................................................................. Page

1.0

SPECIFICATIONS ............................................................................... 1

1.1

Technical Specifications...................................................................... 1

1.2

Ordering Information........................................................................... 4

2.0

Introduction............................................................................................ 6

2.1

Inspecting the Package and Product .................................................... 6

2.2

Product Description - Magnum 6KQ Field Switch.............................. 7

2.2.2

Four-Port Copper Module, 6KQ4-RJ45 .................................... 10

2.2.3 PoE (power pass-through), model P6KQ4-RJ45 10/100Mb 4-port

...... 10

2.2.4 Two-Port Fiber Modules, 2@ 100Mb fiber................................ 11

2.2.5

Two -Port 10 Mb mm Fiber ST Modules................................... 12

2.2.6

SFP Gigabit (1000Mbps) port modules..................................... 12

2.2.7

Packet Prioritization, 802.1p QOS............................................. 13

2.2.8

Frame Buffering and Flow Control............................................ 13

2.2.9

Managed Network Software (MNS-6K ) for 6KQ-Series......... 14

2.3

Features and Benefits......................................................................... 15

2.4

Applications....................................................................................... 16

3.0

Installation........................................................................................... 19

3.1

Locating Magnum 6KQ Switches...................................................... 19

3.2

Connecting Ethernet Media ............................................................... 20

3.2.1

Connecting Fiber Optic ST-type, “twist-lock”........................... 20

3.2.2

Connecting Fiber Optic SC-type, "Snap-In".............................. 21

3.2.3

Connecting Single-Mode Fiber Optic........................................ 21

3.2.4

Connecting Twisted Pair (CAT3, CAT5) .................................. 21

3.2.5 Connecting Twisted Pair (CAT5e or better).............................. 22

3.2.6

Gigabit SFP (Small Form-factor Pluggable) ............................. 23

3.3

DIN-Rail Mounting the Magnum 6KQ.............................................. 25

3.3.1

Mounting Dimensions for 6KQ with metal brackets................. 26

3.4

Powering the Magnum 6KQ Managed Field Switch......................... 27

3.5 Alarm Contacts for monitoring internal power, and Software Traps.... 28

3.6

6KQ Port Module (6KPM) Installation ............................................. 29

3.7 Connecting a Management Console Terminal to 6KQ ........................ 29

4.0

OPERATION....................................................................................... 30

4.1

Switching Functionality..................................................................... 30

4.2

Status LEDs ....................................................................................... 31

4.3

Auto-Cross(MDIX) and Auto-negotiation, for RJ-45 ports............... 31

4.4

Flow-control, IEEE 802.3x standard ................................................. 33

4.5

Power Budget Calculations for 6KQ PM’s with Fiber Media........... 33

5.0

Introduction - Magnum 6KQ Managed Field Switch Port Modules35

5.1

Inspecting the Package and Product .................................................. 35

5.2

6KPM Module Description................................................................ 35

5.2.1

6KQF-2MST Combo Module.................................................... 36

5.2.1a

6KQ2-10ST, 2@10Mb multi-mode FX-ST “twist lock” Module36

Magnum 6KQ Managed Field Switch Installation & User Guide 04/07)

iv

www GarrettCom com

..

5.2.2. 6KQF-2MSC Fiber connector .................................................... 37

5.2.3

6KQF-2SSCL FX-SC-type, Sgl.M ........................................... 37

5.2.4

6KQ3-RJMSC “COMBO” connector....................................... 38

5.2.5 6KQ4-MT MTRJ Small-Form-factor......................................... 38

5.2.6

6KQ4-RJMT, “COMBO” multi-mode FX , MTRJ Small-FF ... 39

5.2.7

6KQ4-MLC LC connector SFF ................................................. 39

5.2.8

6KQ4-RJMLC LC small-form factor and ................................. 40

5.2.9

6KQ4-RJ45 (Twisted Pair), 10/100Mb, 4-Port.......................... 40

5.2.10 PoE power-pass-through, Base unit Model 6KQP-48VDC

................ 41

5.2.11

SFPs, Gigabit (1000Mbps) port modules................................... 42

5.2.12

6KQ-BLNK ............................................................................... 43

6.0

TROUBLESHOOTING...................................................................... 43

6.1

Before Calling for Assistance............................................................ 43

6.2

When Calling for Assistance ............................................................. 44

6.3

Return Material Authorization (RMA) Procedure............................. 44

6.4

Shipping and Packaging Information................................................. 44

APPENDIX A: WARRANTY INFORMATION......................................... 45

APPENDIX B : DC Power Input.................................................................... 46

APPENDIX C: Internal DC Dual-Source Power Input Option.................. 48

Revisions

04/07: Release as Rev A, first printing

Magnum 6KQ Managed Field Switch Installation and User Guide (04/07)

www GarrettCom com

..

THE MAGNUM LINE

Industrial networking products

"Designed and Manufactured in the USA"

Overview

GARRETTCOM, INC. OFFERS THE PREMIUM-QUALITY MAGNUM LINE

OF INDUSTRIAL CONECTIVITY PRODUCTS WITH INDUSTRY-STANDARD

FUNCTIONALITY AND BUILT-IN FIBER CONFIGURABILITY. MAGNUM

PRODUCTS ARE DESIGNED FOR USE IN DEMANDING INDUSTRIAL GRADE,

CARRIER CLASS, POWER UTILITY AND OEM APPLICATIONS WHERE

RELIABILITY IS A PRIMARY CONSIDERATION.

6K-SERIES MANAGED FIELD SWITCHES, GIGABIT, 100 AND 10 MBPS, FIBER AND COPPER

PORTS, MIX-AND MATCH. FEATURES SFF FIBER AND DC POWER IN 1U UNITS.

DX-SERIES SERIAL DEVICE ROUTERS, ETHERNET AND SERIAL

4K-SERIES SWITCHES, 100 AND 10 MBPS, COPPER PORTS WITH OPTIONAL FIBER PORT, WITH

AUTO-NEGOTIATING FULL SWITCHING PERFORMANCE.

QUAD-SERIES FIBER SWITCHES, 100 & 10MBPS, FIBER AND COPPER PORTS, MIXED-SPEED AND

MIXED-MEDIA TYPES, FULL SWITCHING PERFORMANCE.

MP62 AND P62F “OUTDOOR” ETHERNET SWITCHES, FOR TEMPERATURE UNCONTROLLED

LOCATIONS, 6 10/100 AND 2 100MB FIBER PORTS, CAN BE CONNECTED IN STRINGS

MIXED-MEDIA FIBER HUB, 16-PORT, 10/100 AUTO-SENSING

DUAL SPEED 8-PORT AND 16-PORT, 10/100 AUTO-SENSING HUBS

PERSONAL SWITCHES, 10/100MB

8 PORT DUAL-SPEED, AUTO-NEGOTIABLE WITH FIBER OPTION

PERSONAL HUBS, 100MB OR 10/100MB 8-PORT, WITH 2 SWITCHED PORTS (1 FIBER BUILT IN)

PERSONAL HUBS, 10MB SERIES 8-PORT + AUI, STACKABLE TO 5 HIGH, + OPTIONAL BNC OF

FIBER PORT 8 OR 9-PORT AND 4 OR 5-PORT PERSONAL HUBS, W/ MAN. UP-LINK SW.

MEDIA CONVERTERS, 10MB AND 100MB SERIES, ALL MEDIA COMBINATIONS, INCL. FIBER ST,

SC, MM., SINGLE MODE

THE “X-LINE” OF CONFIGURABLE MIXED MEDIA PRODUCTS:

STACKABLE CONCENTRATORS, SNMP OPTIONAL, 13-PORTS

MINI-CONCENTRATORS, 7 PORTS, REPEATERS, 2-PORTS

REPEATER PORT MODULES (RPMS), 6 TYPES FOR ETHERNET MEDIA

COAX TRANSCEIVERS, 10MB SERIES

APR, 07

Magnum 6KQ Managed Field Switch Installation and User Guide (04/07)

1

www GarrettCom com

..

1.0 SPECIFICATIONS

1.1 Technical Specifications

Performance

Filtering / Forwarding Rate:

Ethernet(10Mb):14,880 pps

Fast Ethernet(100Mb): 148,800 pps

Gigabit Ethernet (1000Mb): 1, 488,000 pps

Switching Processing Type: Store and Forward with IEEE 802.3x full-

duplex flow -control, non-blocking

Data Rate: 10Mbps,100Mbps and 1000Mbps

Address Table Capacity: 4K node, self-learning with address aging

Packet buffer size : 240KB for 10/100 and 120KB for 1000Mb

Latency: 5 s + packet time (100 to 100Mbps)

15 s + packet time (10 to 10 Mbps, and 10 to 100Mbps)

Throughput with 12 10/100 and 2Glink max.- 4.76M pps (Transmit)

Back plane- 2.66Gb/s per slot

Network Standards and Compliance, hardware

Ethernet V1.0/V2.0 IEEE 802.3: 10BASE-T,

IEEE 802.3u: 100Base-TX, 100BASE-FX

IEEE 802.3z: 1000BASE-X Ethernet (Auto-negotiation)

IEEE 802.3ab: 1000BASE-X Ethernet

IEEE 802.1p: Priority protocol

IEEE 802.1d: Spanning tree protocol

IEEE 802.1w: Rapid Spanning tree protocol

IEEE 802.1q: VLAN Tagging

IEEE 802.3x: Flow Control

IEEE 802.3ad: Link Aggregation (Trunking)

IEEE 802.1x: Port based Network access control

IEEE802.3af: Power over Ethernet

Maximum 10 Mbps Ethernet Segment Lengths

Unshielded twisted pair - 100 m (328 ft)

Shielded twisted pair - 150 m (492 ft)

10BASE-FL multi-mode fiber optic - 2 km (6,562 ft)

10BASE-FL single-mode fiber optic - 10 km (32,810 ft)

Maximum Standard Fast Ethernet Segment Lengths:

10BASE-T (CAT 3, 4, 5 UTP) - 100 m (328 ft)

100BASE-TX (CAT 5 UTP) - 100 m (328 ft)

Shielded twisted pair - 150 m (492 ft)

100BASE-FX, half-duplex, multi-mode - 412 m (1350 ft)

100BASE-FX, full-duplex, multi-mode - 2.0 km (6,562 ft)

100BASE-FX, half-duplex, single-mode - 412 m (1350 ft)

100BASE-FX, full-duplex, single-mode - 20.0 km (66KQ ft)

100BASE-FX, full-duplex, Long Reach - 40.0 km (122K ft)

Maximum Standard Gigabit Ethernet Segment Lengths:

1000BASE-T (CAT5e or higher is recommended) - 100 m (328 ft)

1000BASE-SX, full-duplex, multi-mode(62.5m cable) - 220m

Magnum 6KQ Managed Field Switch Installation and User Guide (04/07)

2

www GarrettCom com

..

1000BASE-SX, full-duplex, multi-mode(50m cable) - 550m

1000BASE-LX, full-duplex, single-mode(62.5m cable) -5Km

Fiber Multi-mode connector types supported:

Fiber Port, ST-type (twist-lock):Fiber multi-mode, 10Mb 10BASE-FL

Fiber Port, MTRJ-type (plug-in):SFF Fiber multi-mode100BASE-FX

Fiber Port, SC-type (snap-in):Fiber optic multi-mode, 100BASE-FX

Fiber Port, ST-type (twist-lock): Fiber optic m.-mode, 100BASE-FX

Fiber Port, 1000BASE-FX, SFP modules

Fiber Single-mode connector types:

Fiber Port, SC-type: Fiber optic single-mode, 100BASE-FX

Fiber Port, LC-type Fiber SFF single-mode, 100BASE-FX

Fiber Port, 1000BASE-FX, SFP modules

LEDs: Per Port (one set at the port, one set on swivel top on right side)

LK: Steady ON when media link is operational

ACT: ON with receiver port activity

FDX/HDX: ON = Full-Duplex Mode

OFF = Half-Duplex Mode

100/10: ON = 100Mbps speed

OFF = 10 Mbps

Operating Environment

Ambient Temperature:

-40 to 140 F (-40 to 60C) for UL60950 and Component Parts rating

-60 to 195 F (-50 to 85C) for IEC 60068 Type Test short term rating

Storage Temperature: -60to 210F (-50to 100C)

Ambient Relative Humidity: 5% to 95% (non-condensing)

Altitude: -200 to 13,000 ft. (-60 to 4000m)

Conformal Coating (humidity protection) option: Request quote

Alarm Relay Contacts

One NC indicating internal power, one NC software controllable

Packaging

Enclosure: High strength extruded aluminum

Dimensions: 6.85 in. H x 7.5 in. W x 2.0 in. D

17.4 cm H x 19.1 cm W x 5.08 cm D

Cooling method: Convection, fully-enclosed ribbed-surface aluminum case

used as a sink, designed for vertical mounting, no fans

Weight: 3 lbs. (1.3 kg)

Management Console connector

Serial RJ-45, see details at sec. 3.7

DC Power Supply (Internal, floating ground design)

24VDC Power Input nominal (18 to 36VDC range)

-48VDC Power Input nominal (36 to 60 VDC range)

125VDC Power Input nominal (88 to 150VDC range)

Std. Terminal Block : “ -, GND, + ”

Power Consumption:

35 watts typical (for a fully loaded fiber model)

Magnum 6KQ Managed Field Switch Installation and User Guide (04/07)

3

www GarrettCom com

..

12 watts typical (for a small 4 port copper-only model)

DC-DUAL POWER SOURCE (OPTIONAL)

For DC internal power supplies at –48VDC, 24VDC and 125VDC, with

the Dual-Source option (

for continuity of operation when either of the DC input

sources are interrupted)

, see Appendices B and C.

Dual-Source Terminal Block : “ –A, -B, +A, +B ”

6KQ Mounting:

Vertical mounting normal. Suitable for wall or DIN-Rail mounting (6KQ)

Agency Approvals and Standards Compliance:

UL listed (UL60950), cUL, CE, Emissions meet FCC Part 15 Class A

NEBS Level 3 and ETSI Compliant

IEEE 1613 Class 2 Environmental Standard for Electric Power Substations

See also Note for Power Substations in Section 3.2.4, 3.7, and 5.2.9

IEC 61850 EMC and Operating Conditions Class C for Power Substations

NEMA TS-2 and TEES for DC-powered and PoE-powered traffic control

equipment

Class1 Division 2 and ATEX for hazardous locations, pending

Warranty: Three years, per UL 60950 temperature rating

Made in USA

See the Configuration Guide on the GCI web site at

http://www.garrettcom.com/techsupport/insertion_guides/6kqcg.pdf

for configurations and options..

Email

[email protected]

for additional information.

Magnum 6KQ Managed Field Switch Installation and User Guide (04/07)

4

www GarrettCom com

..

1.2 Ordering Information

Magnum Managed Field Switch (16 ports max)

MODEL DESCRIPTION

Magnum 6KQ- 24VDC Magnum 6KQ Managed Field Switch, base unit with 24VDC

power supply and four 10/100 copper ports. May be configured with a selection of

10/100/1000 fiber and copper port connector types from a family of 6KQ port modules per

the 6KQ configuration guide, 16 total ports max. Heavy duty and environmentally

hardened, no fans. Dual LEDs for all-around status viewing. Wire speed filtering and

forwarding across all ports, 802.3x flow control, 802.1p priority packet processing, self-

learning 4K-node address table, large 240KB packet buffers for 10/100 and 120KB for

1000Mb.

For licensed managed networks software (MNS-6K, RS-Ring and S-Ring) including

GUIs for ease-of-use and industry-leading security features, see separate data sheets.

Magnum 6KQ -48VDC: Same as 6KQ-24VDC except the power input is -48VDC

Magnum 6KQP-48VDC: Same as 6KQ-48VDC except the four 10/100 RJ-45 are PoE

Magnum 6KQ-125VDC: Same as 6KQ-24VDC except the power input is 125VDC

PSAC-24V60 : External Hardened Power Supply for AC to 24VDC, 60 watts, panel or

DIN-RAIL mount.

PSAC-48V150 : External Hardened Power Supply for AC to 48VDC for PoE, 150 watts,

panel or DIN-RAIL mount.

Please use this URL: for the complete Configuration Guide for the Magnum 6KQ.

http://www.garrettcom.com/techsupport/insertion_guides/6kqcg.pdf

Configuration Options:

Each Magnum 6KQ base unit may be configured with a choice of 3 modular slots.

Following modules can be configured in Slot B and D (Slot C is 100Mb Fiber only)

Magnum 6KQ Port Modules

6KQ4-RJ45 TP Module, w/four 10/100Mbps copper ports,

P6KQ4-RJ45 PoE 6KQ module, four 10/100 copper ports with PoE on data pairs,

may be configured in slot B only

6KQ4-RJMLC “2+2” module, w/two RJ-45 ports and two 2km mm LC connectors

6KQ4-RJSLC “2+2” module, w/two RJ-45 ports and two 15km Sgl-m LC connectors

6KQ4-RJMT “2+2” module, w/two RJ-45 ports and two 2km mm MTRJ connectors

6KQ2-10ST Two 10Mb mm Fiber 2km FL ST’s

6KP4-MLC SFF mm Fiber module, w/ four 100Mb mm FX LC connectors

6KP4-MT SFF mm Fiber module, w/ four 100Mb mm FX MT-RJ connectors

6KQ2-MST Two 100Mb Fiber module, w/ four 100Mb 2km FX ST connectors

6KQ3-RJMSC “2+1” module, w/two RJ-45 ports and one 2km mm FX SC’s

6KQ2-MSC Two 100Mb Fiber module, w/ four 100Mb 2km FX SC connectors

6KQ2-SSC Two 100Mb Fiber module, SM w/ 100Mb 20km FX SC connectors

6KQ2-SSCL Two 100Mb Fiber module, SM w/ 100Mb 20km FX SC connectors

Fiber-only Slot C configuration choices

Magnum 6KQ Managed Field Switch Installation and User Guide (04/07)

5

www GarrettCom com

..

6KQF-4MT “4 ports” module, w/four 100Mb mm 2km FX MTRJ’s fiber ports

6KQF-4MLC “4 ports” module, w/four 100Mb mm 2km FX LC’s fiber ports

6KQF-4SLC “4 ports” module, w/four 100Mb Sm, 15km FX LC’s fiber ports

6KQF-2MST “2 ports” module, w/two 100Mb mm, 2km FX ST’s fiber ports

6KQF-2MSC “2 ports” module, w/two 100Mb mm, 2km FX SC’s fiber ports

6KQF-2SSC “2 ports” module, w/two 100Mb Sm, 20km FX SC’s fiber ports

6KQF-2SSCL “2 ports” module, w/two 100Mb Sm, 40km FX SC’s fiber ports

6KQF-2MLC “2 ports” module, w/two 100Mb mm, 2km FX LC’s fiber ports

6KQF-2SLC “2 ports” module, w/two 100Mb Sm, 15km FX LC’s fiber ports

6KQF-2MT “2 ports” module, w/two 100Mb mm, 2km FX MTRJ’s fiber ports

6KQF-1MST “1 port” module, w/one 100Mb mm, 2km FX ST’s fiber ports

6KQF-1MSC “1 port” module, w/one 100Mb mm, 2km FX SC’s fiber ports

6KQF-2SSC “1 port” module, w/one 100Mb Sm, 20km FX SC’s fiber ports

6KQF-1SSCL “1 port” module, w/one 100Mb Sm, 40km FX SC’s fiber ports

6KQ-BLNK Blank cover for 1 un-used 6KQ module slot

Gigabit(1000Mb) module choices, slot D only

6KQ-2GSFP “SFP Gig” module, w/two SFP pluggable, open transceiver ports

6KQ-2GCU “Copper Gig” module, w/two10/100/1000 RJ-45 ports

6KQ-2GSFPCU “Copper Gig” module, w/ one SFP pluggable open transceiver port +

one10/100/1000 RJ-45 ports

6KQ-1GSFP “SFP Gig” module, w/one SFP pluggable, open transceiver ports

6KQ-1GCU “Copper Gig” module, w/one10/100/1000 RJ-45 ports

Gigabit (1000Mb) SFP (Small Form Pluggable) Transceiver option (6KQ)

SFP-SX Giga SFP transceiver, 1000Mb-SX, 850nm wavelength, 500m

SFP-LX10 Giga SFP transceiver, 1000Mb-SX, 1310nm wavelength, 10Km

SFP-LX25 Giga SFP transceiver, 1000Mb-SX, 1310nm wavelength, 25Km

SFP-ZX40 Giga SFP transceiver, 1000Mb-SX, 1550nm wavelength, 40Km

SFP-ZX70 Giga SFP transceiver, 1000Mb-SX, 1550nm wavelength, 70Km

MNS-6K License- MNS-6K managed software is pre-loaded from the factory.

S-RING Key: S-Ring and RS-Ring Redundancy Manager licensed software for redundant

ring management. One S-Ring or RS-Ring key is for licensed use one 6K-managed self

healing Ring.

CONSOLE- CBLQD Serial-RJ45 cable, DB9 RS-232 “ null-modem female connector

on one side and RJ-45 on the other side for the RJ-45 Management port (Console port).

CONSOLE- CBLQU USB -RJ45 cable, USB connector on one side and RJ-45 to the

other side for the RJ-45 Management port (Console port).

DIN-RAIL-6KQ Din-Rail holder for a secure vertical mount, with screws for 6KQ

KQ-CABLE-BKT Metal bracket for 6KQ, used for cable strain relief, for vertical

mount

CONFORM05 CRM conformal coating, heavy duty silicone at 5 mil thickness, for

interior PCBs, PS and modules

GarrettCom, Inc. reserves the right to change specifications, performance

characteristics and/or model offerings without notice.

Magnum 6KQ Managed Field Switch Installation and User Guide (04/07)

6

www GarrettCom com

..

2.0 Introduction

2.1 Inspecting the Package and Product

Examine the shipping container for obvious damage prior to installing this

product; notify the carrier of any damage that you believe occurred during shipment or

delivery. Inspect the contents of this package for any signs of damage and ensure that

the items listed below are included.

This package should contain:

1 Magnum 6KQ Managed Field Switch, base unit

(configured with user-selected port module options installed)

1 Set of two metal vertical mounting brackets, with screws to the case

1 Installation and User Guide (this manual)

1 Product Registration Card

Remove the items from the shipping container. Be sure to keep the shipping

container should you need to re-ship the unit at a later date. To validate the product

warranty, please complete and return the enclosed Product Registration Card to

GarrettCom, Inc. as soon as possible.

In the event there are items missing or damaged, contact the party from whom

you purchased the product. If the unit needs to be returned, please use the original

shipping container if possible. Refer to Section 6, Troubleshooting, for specific return

procedures.

Magnum 6KQ Managed Field Switch Installation and User Guide (04/07)

7

www GarrettCom com

..

2.2 Product Description - Magnum 6KQ Field Switch

Magnum 6KQ Managed Field Switches provide maximum configurability in

their class. The fiber-rich 6KQ can be configured with up to 12 100Mb fiber ports and

two Gigabit ports. For 10/100 copper, regular or PoE-equipped 10/100 RJ-45 or

10/100/1000 copper ports may be configured to a maximum or 12 at 10/100 and 2 Gig

ports. Magnum 6KQ comes with the best-of-breed MNS-6K managed networks software

featuring GUI ease of use, Secure Web Management, SNMPv2,v3 management, 802.1p

QoS Prioritization, Tag-based VLANs, IGMP Snooping and IGMP-L2 multicast

management, port security, RADIUS and TACACS+ support, and a choice of

redundancy options including RSTP and GarrettCom’s rapid-ring-recovery S-Ring and

RS-Ring products. See the Managed Networks Software (MNS-6K) datasheet for more

information.

Magnum 6KQs are ideal for building a switched, hardened Ethernet network

infrastructure, connecting edge devices such as PLCs and IEDs with upstream switches

or routers. Designed for use in industrial applications such as factory floors and control

cabinets, industrial video surveillance systems with PoE, power utility substations,

tariffed carrier field facilities, or transportation and oil and gas, the rugged Magnum 6KQ

handles stressful workloads (mixes of bursty data traffic and priority streaming traffic) as

well as harsh environmental conditions.

Advanced thermal design techniques with ribbed –surface Aluminum

cases for maximum heat

dissipation and a sealed

case design enables the unit

to operate in harsh

Industrial grade

environments efficiently.

Heavy duty Ethernet

Switch jobs are readily

accommodated with an extended temperature rating of -40˚C to 60˚C by the UL

Component Parts method, or -50˚C to 85˚C by the IEC 60068 Type-Test method. With

options such as several popular DC power input types (optional AC power) and DIN-Rail

mounting, the hardened Magnum 6KQ is a “multi-purpose” Industrial Ethernet Switch.

Magnum 6KQ Managed Field Switch Installation and User Guide (04/07)

8

www GarrettCom com

..

The 6KQ managed switches also provide PoE options via power –

inside PoE modules on one of A, B or C slots and allows the users to select a wide option

of combo PoE modules to support 802.3af pd devices. See details for PoE modules in sec

5.2.10. The Power Sourcing Equipment (PSE) is fully compatible with Powered Devices

(PD)(e.g wireless access points, IP phones) that comply with the IEEE 802.3af PoE

standard. The PoE switch ports have an auto-sensing algorithm, so that they provide

power only to 802.3af, PoE end devices. PoE is managed by a multi-stage handshake

to protect equipment from damage and to manage power budgets .The PoE ports

will discontinue supplying power when the PoE powered devices are disconnected. This

feature supports the 802.3af PoE PSE standard for over-current protection, under-current

detection, and fault protection.

High performance features include non-blocking unicast traffic speed on all ports and

802.1p QoS Traffic Prioritization. Magnum 6KQ switches are “plug-and-play” and are

designed for use in connecting edge devices such as PLCs, IEDs and PoE video cameras

with upstream switches and routers where a mix of bursty data traffic and priority

streaming traffic

for video

surveillance and

cell-tower

applications are

present. Magnum 6KQ Field Switches are provided with LAN management software

including SNMP, Tag- and Port-based VLANs, IGMP-L2 and IGMP Snooping, and Port

Security with control via GUI and command line interface (CLI). For high availability

LANs using ring topologies, Spanning Tree Protocol, RSTP, Link-Loss-Learn and S-

Ring are available. Dual-Homing is a software configuration feature. See the Managed

Networks Software (MNS-6K) and S-Ring datasheets for additional details on the

comprehensive set of software programs and options.

Magnum 6KQ Managed Field Switches have heavy-duty aluminum

cases and are readily available with standard Industrial grade 24VDC power. Alternative

internal DC power options are available. DC power input types may be 24V, 48V, 125V,

and dual source DC input is optional on all 6KQ’s. (AC power is available via an

external power supply unit, see Section 3.4 for details).

Magnum 6KQ Managed Field Switch Installation and User Guide (04/07)

9

www GarrettCom com

..

1 2 3 4

AC

F/H

ACT

F/H

LK LK LK LK

ACT

F/H

ACT

F/H

Alarm Relay contacts provided on each Magnum 6KQ Switch monitor the hardware and

software through traps, providing a record of any losses of power signals and other user-

defined software events. See Section 3.5 for details.

The wide selections of Quad port (queen size) modules are key to the flexibility and

adaptability of Magnum 6KQs. Some of the popular 4 ports modules are described

below. For a list of all the modules and options, see Section 1.2

NOTE: The 6KQ modules can only be configured at the factory.

2.2.1 Four-port SFF fiber modules (6KQ4-MTRJ, 6KQ4-MLC), 100Mb

fiber

Fig.2.2.1 :

SFF Fiber Port Modules,

6KQ4-MTRJ (above) and

6KQ4MLC or -SLC (below)

In a four-port SFF (Small Form Factor)

fiber port module, all of the fiber ports

are of the same speed (100Mb), mode,

and connector type. Small Form Factor (SFF) Fiber Ports come in multi-mode forms

MT-RJ or LC-type connectors, and single-mode form LC-type connectors.

The 100Mb fiber four-port modules for the Magnum 6KQ’s normally are set

(factory default) to operate in full-duplex mode for best fiber distance and performance.

Using the 6K-MNS software, the user may select full- or half-duplex mode per-port

through set port command.

The set-up of the software

(See Magnum 6K-MNS

Software Manual) gives the

user flexibility to adapt to any

FDX or HDX type of Fast Ethernet devices).

There are three LED’s per fiber port. The Link (LK) LED indicates “ready for

operation” on that port when lit. The F/H LED indicates operation in full-duplex mode

when ON (half-duplex when OFF). The blinking ACT LED indicates receiving Activity

LK LK

A

CT

F/H

A

CT

F/H

A

C

F/

A

C

F/

1 2 3 4

Magnum 6KQ Managed Field Switch Installation and User Guide (04/07)

10

www GarrettCom com

..

on the port. A fiber cable must be connected into a SFF port and the Link (LK) indicator

for that port must be ON (indicating there is a powered-up device at the other end of the

cable) in order for a LK LED to provide valid indications of operating conditions on that

port.

2.2.2 Four-Port Copper Module, 6KQ4-RJ45

The 6KQ’s 4-port Copper module, model 6K4-RJ45, provides four 10/100Mb switched

RJ-45 ports. The 10/100Mb

switched ports normally (as a

default setting) are independently

N-way auto-negotiating and auto-

crossover (MDIX) for operation at 10 or 100Mb speed in full- or half-duplex mode. (i.e.,

each independently selects a mode and speed to match the device at the other end of the

twisted pair cable).

(See Section 4.3 for auto-negotiation and MDIX details).

On the model 6KQ-RJ45 module, there are four LEDs for each port, two

integrated into the connector, and two below the connector. The LK (Link) LED

indicates “ready for operation” on that port when lit. The blinking ACT (Activity) LED

indicates receiving Activity on that port when lit. The 10/100 LED indicates operation at

100Mb speed when ON and at 10 Mb speed when OFF (when auto-negotiation is not

disabled). The FDX/HDX LED is ON to indicate full-duplex operation and OFF to

indicate the half-duplex mode. A twisted pair cable must be connected into an RJ-45 port

and the Link (LK) indicator for that port must be ON (indicating there is a powered-up

device at the other end of the cable) in order for a LK LED to provide valid indications

of operating conditions on that port.

Using the 6KQ (MNS-6K) management software, the user may disable auto-

negotiation and fix the desired operation of each RJ-45 port. The user may select 10Mb

or 100Mb speed and full- or half-duplex mode per-port as per user requirements. (See

Magnum MNS-6K Software Manual for details info.).

2.2.3 PoE (power pass-through), model P6KQ4-RJ45 (MDIX), 10/100Mb 4-port

The PoE (Power-over-Ethernet) RJ-45 ports are similar to regular RJ-45 ports,

except they have the capability of providing power on each port to power up the PD

devices, per the IEEE802.3af PoE standard. The power-pass-through PoE modules are

1 2 3 4

10/10

L

F/

AC

Magnum 6KQ Managed Field Switch Installation and User Guide (04/07)

11

www GarrettCom com

..

dependent upon the -48VDC input power to supply the PD power for these RJ-45

(10/100) ports. Each port supplies up to 15watts to power the PoE PD devices. A

maximum of 8 PoE ports can be configured in the A and B slots of a 6KQ switch with -

48vdc power input. The PoE modules are also available with mix–n-match fiber modules

configured in other 6KQ slots. Please check the Configuration Guide and the ordering

information Sec.1.2 for all the various P6K PoE module options.

The LEDs

on

P6KQ4-RJ45- PoE modules are slightly different compared to regular (non-PoE) RJ-45

modules as shown in Fig 2. When the PoE port is in use, the PoE LED is ON when

connected properly to an 803.af compliant PD device on that port. When non-PoE

devices are connected, the PoE LED is OFF. The operation of Ethernet data traffic is not

affected by PoE.

LINK and ACTIVITY LEDS are combined on the PoE modules into one LED that is

marked as LINK/ACT, as shown in the diagram.

2.2.4 Two-Port Fiber Modules, 2@ 100Mb fiber

The two-port modules are available as two 100Mb fiber ports. ST or SC connector

styles are available utilizing multi-mode or single-mode fiber optics. These fiber

modules may be factory configured with a choice of them in slot B and D only.

The fiber port’s LEDs indicate status the same as the SFF fiber modules in Section 2.2.2

above. Color-coding on the panel of the module shows which LEDs belong to which

port.

2@ 100 Mb SC 2@ 100 Mb ST

1 2 3 4

10/10

L

K

F/

AC

4

FULL/HALF

1

PoE

LK

/

ACT

2

3

10/100

P6KQ4-RJ45

4 Port@ 10/100Mb PoE Copper ports

4

2

1

3

TX RX

TX LK RX

L

ACT

F/

ACT

F/

ACT

TX RX

TX LK RX

L

K

ACT

F/

ACT

F/

Magnum 6KQ Managed Field Switch Installation and User Guide (04/07)

12

www GarrettCom com

..

2.2.5 Two -Port 10 Mb mm Fiber ST Modules

The 2-port @10Mb ST fiber modules behave the same as the 2@100Mb ST

fiber modules except for the 10Mb speed.

The default setup on the 10Mb fiber module is half-duplex, which allows the Magnum

6KQ Switch to connect to any 10Mb hub or media converter or almost any other device

with a 10Mb fiber Ethernet port. The default setting of the 100Mb fiber module is full

duplex. User mode-control per port through the MNS “port settings”

software is the

same as the other 6KQ modules.

The fiber ports support fiber cabling distances according to the 10BASE-FL

and 100BASE-FX standards, i.e., 2km distance for multi-mode fiber. (Single-mode for

greater distances may be available as a special order, request quote).

2.2.6 SFP Gigabit (1000Mbps) port modules

The Gigabit port options for the modular slot come in a few different

configurations of Fiber SFP’s or RJ-45’s. The Magnum 6KQ offers only SFPs (Small

Form Pluggable) for Gigabit speed. There are multiple choices of SFP Gigabit

transceiver types to combine with RJ-45’s for the modular slot. Up to two Gigabit ports

(max.) can be configured in the modular slot D only. An example of a two Gb module is

the 6KQ-2GSFP (SFP fiber). An example of a single Gigabit module is the 6KQ-1GCU

(10/100/1000Mb RJ-45 ports). A combo option of Gigabit copper and SFP fiber (6KQ-

2GSFPCU) is shown below in the figure.

1@ 10/100/1000Mb RJ-45 + 1@ 1000Mb SFP

The 6KQ Modules provide an SFP opening for insertion of industry-standard

SFP transceivers to provide Gigabit (Gb) media flexibility. Gigabit SFP modules are

available in both multi-mode (550m) and single-mode (10, 25, 40, 70) km fiber options

as well as a Gigabit copper option.

Magnum 6KQ Managed Field Switch Installation and User Guide (04/07)

13

www GarrettCom com

..

There are three LEDs mounted on each Gigabit port module. The Gigabit fiber has LEDs

that indicate F/H (Full/Half duplex), LK (Link status) and ACT (receiving activity) on

that port when lit. The copper Gigabit ports come with speeds indicating

(10/100/1000Mb) LEDs also.

The operation of the Gigabit SFP and 10/100/1000 RJ-45 ports is as described

for those port types above. For detailed information about 10Mb mm ST fiber half of the

module, see Section 2.2.5.

2.2.7 Packet Prioritization, 802.1p QOS

Quality of Service means providing consistent predictable data delivery to

users from datagram paths that go all across a network. As a LAN device, the Magnum

6KQ can do its part to prevent any QOS degradation while it is handling Ethernet traffic

through its ports and buffers.

The Magnum 6KQ switching hardware supports the IEEE 802.1p standard and

fulfills its role in support of QOS, giving packet processing priority to priority tagged

packets according to the 802.1p standard. In addition to hardware support for QOS, the

MNS software (R2) supports two priority queues that can be shared across the eight

levels of defined packet priorities for application-specific priority control by the user

through software configuration settings.

2.2.8 Frame Buffering and Flow Control

Magnum 6KQ’s are store-and-forward switches. Each frame (or packet) is

loaded into the Switch’s memory and inspected before forwarding can occur. This

technique ensures that all forwarded frames are of a valid length and have the correct

CRC, i.e., are good packets. This eliminates the propagation of bad packets, enabling all

of the available bandwidth to be used for valid information.

While other switching technologies (such as "cut-through" or

"express") impose minimal frame latency, they will also permit bad frames to propagate

out to the Ethernet segments connected. The "cut-through" technique permits collision

fragment frames (which are a result of late collisions) to be forwarded which add to the

network traffic. Since there is no way to filter frames with a bad CRC (the entire frame

must be present in order for CRC to be calculated), the result of indiscriminate cut-

through forwarding is greater traffic congestion, especially at peak activity. Since

collisions and bad packets are more likely when traffic is heavy, the result of store-and-

forward operation is that more bandwidth is available for good packets when the traffic

Magnum 6KQ Managed Field Switch Installation and User Guide (04/07)

14

www GarrettCom com

..

load is greatest.

When the Magnum 6KQ Switch detects that its free buffer queue space is low,

the Switch sends industry standard (full-duplex only) PAUSE packets out to the devices

sending it packets to cause “flow control”. This tells the sending devices to temporarily

stop sending traffic, which allows the traffic to catch-up without dropping packets. Then,

normal packet buffering and processing resumes. This flow-control sequence occurs in a

small fraction of a second and is transparent to an observer.

Another feature implemented in the Magnum 6KQ Switches is a collision-based flow-

control mechanism (when operating at half-duplex only). When the Switch detects that

its free buffer queue space is low, the Switch prevents more frames from entering by

forcing a collision signal on all receiving half-duplex ports in order to stop incoming

traffic.

2.2.9 Managed Network Software (MNS-6K ) for Magnum 6KQ-Series

Magnum 6KQ’s come with Rel3.6 licensed MNS-6K software, which allows the user to

configure the Magnum 6KQ as a Managed Switch and implements security features and

other software enabled features.

(NOTE: Magnum 6KQ managed switch will work with Rel 3.6 firmware

or higher version only, using any other MNS-6K version will not support the

hardware)

For additional information about MNS-6K, see the Magnum MNS-6K

Software User guide in pdf format, a separate document normally accessible via your

web-browser, at

ftp://ftp.garrettcom.com/

or FTP client program at ftp.GarrettCom.com using

user : m6kuser

password : m6kuser

All MNS-6K software information, including new releases and upgrades related to MNS-

6K software, can be accessed and download from GarrettCom’s FTP site.

Alternatively, for the latest documentation and information, or needed

GarrettCom’s MIBs for SNMP, visit

www.GarrettCom.com/techsupport/index.htm#software

and look for the

Magnum MNS-6K info.

For interactive training software which shows basic and advanced info about

the Magnum MNS-6K management software and for a useful tool for first time users,

visit

Magnum MNS-6K Operator Training

.

You may also email: info@GarrettCom.com

for further information.

Page is loading ...

GarrettCom Magnum 6KQ User manual

This manual is also suitable for

GarrettCom Magnum 6KQ User manual

Related papers

Other documents