Akura APTMP221DR is a versatile 3-in-1 device that combines a radio, CD player, and MP3 player. You can listen to your favorite FM stations or CDs, or play MP3 files from a USB drive or SD card. The device also has a built-in clock and alarm so you can wake up to your favorite music. With its compact size and stylish design, the Akura APTMP221DR is the perfect addition to any home or office.
Akura APTMP221DR is a versatile 3-in-1 device that combines a radio, CD player, and MP3 player. You can listen to your favorite FM stations or CDs, or play MP3 files from a USB drive or SD card. The device also has a built-in clock and alarm so you can wake up to your favorite music. With its compact size and stylish design, the Akura APTMP221DR is the perfect addition to any home or office.
Customer Help Line 01422 263313
Opening hours Mon-Fri 8 am – 8pm. Sat 9 am – 4pm. Sun 11am –
4pm “Bank holidays as Sun”
I N S T R U C T I O N M A N U A L
www.ekey.co.uk (24HR)
MP3/CD/Radio
Micro System
APTMP221DR
WARNING
E-1
TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
WARNING : SHOCK HAZARD-DO NOT OPEN
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
LIGHTNING FLASH WITH ARROWHEAD SYMBOL -
within an equilateral triangle, is intended to aler
t the
user to the presence of uninsulated dang
erous
voltage within the products enclosure that may
be of
sufficient magnitude to constitude a risk of ele
ctric
shock to per
sons.
EXCLAMATION POINT -
within an equilateral triangle,
is used to indicate that a specific component sha
ll be
replaced only by the component specified in
that
documentation for safety re
ason.
The following label has been affixed to the unit, listing the proper procedure for working with the laser beam:
CLASS 1 LASER PRODUCT LABEL -
This label is attached to the place as illustrated to inform tha
t the
apparatus contains a laser compo
nent.
WARNING LABEL INFORMING OF RADIATION -
This lab
el is placed inside the unit. As shown in the illustration. To
warn against further measures on the unit. The equipment contains
a laser radiating laser rays according to the limit of laser product of
class 1.
CLASS 1 LASER PRODUCT
KLASS 1 LASER AP
PARAT
LUOKEN 1 LAISER
LAITE
KLASSE 1 LASER PR
ODUKT
Correct disposal of this Product
(Waste Electrical & Electronic Equipment (WEEE)
The crossed
out “Wheelie bin” is intended to show that this appliance
must not be pl
aced with ordinary household waste at the end of its
us
eful life. To prevent possible harm to the environment or human
health from
uncontrolled waste disposal,
please
keep separate from
other h
ousehold waste and recycle it responsibly to promote the
sustainable reuse of mat
erial
resources.
Household
users should contact either the retailer where you
purchased
the product, or their local government office for details of
where and how you can take this item for environmentally safe re-
cycling.
Business users should contac
t their supplier and check the terms and
conditions of the
purchase contract. This product must not be mixed
with other commercial wastes for disposal
SAFETY INSTRUCTIONS
E-2
1. READ INSTRUCTIONS - All the safety and operating instructions should be read before the appliance is operated.
2. RETAIN INSTRUCTI
ONS - The safety and operating instruction should be retained for future reference.
3. HEED WARNI
NGS - All warnings on the appliance and in the operating instructions should be adhered to.
4. FOLLOW INSTRUCTI
ONS - All operating instructions should be followed.
5. WATER AND MOIST
URE - The appliance should not be used near water, for example, near a bathtub, washbowl,
kitchen sink, laundrytub, swimming pool or in a wet basement.
6. VENTILATI
ON - The appliance should be situated so that its location or position does not interfere with its proper
ventilation. Do not place on bed, sofa, rug or similar surface that may block the ventilation openings, in a built-in
installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openin
gs.
7. H
EAT - The appliance should be situated away from heat sources such as radiators, stoves, or other appliances
(including amplifiers) that produce he
at.
8. POWER SOU
RCE - The appliance should be connected to power supply only of the type described in the
operating instructions or as marked on the applian
ce.
9. POWER CORD PROTECT
ION - Power supply cords should be routed so that they are not likely to be walked
on or pinched by items placed upon or against th
em.
10. OBJECT and LIQUID ENT
RY - Care should be taken so that objects do not fall and liquids are not spilled into
the enclosure through openin
gs.
11. ESD WARN
ING - The display does not function properly or no reaction to operation of any the control may due
to the electrostatic discharge. Switch off and unplug the set. Reconnect after a few seconds.
12. DAMAGE REQUIRING SERVI
CE - The appliance should be serviced by qualified service personnel when:
a. The power-supply cord or plug has been damage
d.
b. Objects have fallen into, or liquid has been spilled into the appliance enclosur
e.
c. The appliance has been exposed to ra
in.
d. The appliance has been dropped, or the enclosure damag
ed.
e. The appliance does not appear to operate normall
y.
13. SERVICI
NG - The user should not attempt to service the appliance beyond that described in the user operating
instructions. All other servicing should be referred to qualified service personnel
.
Note
s:
a. Dirty or scratched CD may cause a skipping problem. Clean or replace the
CD.
b. If an error display or malfunction occurs, disconncet the AC cord and remove all the batteries. Then turn the po
wer
back on.
BEFORE OPERATION
Notes: CONCERNING COMPACT DISCS.
Since dirty, damaged or warped discs may damage the appliance, care should be taken of the followings ite
ms:
a. Usable compact discs. Use only compact disc with the mark shown bel
ow.
b. CD compact disc only with digital audio signa
ls.
Plug the AC power lead into a suitable 3 pin AC Socket. The mains voltage for this appliance is
220 - 240V AC 50 Hz. Do NOT use an alternative supply.
AC POWER
POWER SOURCE
LOCATION OF CONTROLS
E-3
1.) FM STEREO INDICATOR
2.) CD OPEN
3.) LCD DISPLAY
4.) REMOTE SENSOR
5.) FUNCTION SELECTOR / POWER OFF
6.) STOP
7.) SKIP +
8.) SKIP -
9.)
10.)
BAND SELECTOR
11
.)
VOLUME CONTROL
12
.)
PLAY / PAUSE
13
.)
MODE
14
.)
PROGRAM
15.)
ALBUM
16
.)
TUNING CONTROL
17
.)
BATTERIES BACKUP
18
.)
LEFT / RIGHT SPEAKER JACK
19
.)
MINUTE
20.)
HOUR
21
.)
TIME SET
AC POWER CO
RD
1
4
10
5
6
7
8
11
12
13
14
15
17
18
21
16
19
20
2 3
9
Notes:
SENSOR WINDOW OF THE RECEIVER
- Use batteries of the same type. Do not mix battery types together.
If the range of the remote control decreases the batteries will be exhausted.
Do NOT break open or throw on a fire, or place in the domestic waste exhausted batteries.
For disposal call your local waste disposal authority.
Do not place objects in front of the player, this will stop or reduce the operation of the remote control.
If other appliances are controlled by remote control, there is a possibility of interference from one
remote control to the other appliance. This is normal and cannot be helped.
BATTERY INSTALLATION
Insert 2 x “AAA” size batteries into the battery compartment. Be sure that the batteries are inserted
correctly to avoid damage to the remote control. Always remove the batteries when the remote
control will not be used for a long period of time, as this will cause leakage to the batteries a
nd
subsequently damage to your set.
REMOTE CONTROL
E-4
1. PLAY / PAUSE
2. SKIP -
3. PROGRAM
4. ALBUM UP
5. STOP
6. SKIP +
7. MODE
8. +10 TRACK
1
2
5
6
3
7
4
8
GENERAL OPERATION
1. Set the “FUNCTION” selector to “RADIO” mode.
2. Select desired band by using the “BAND” selector.
3. Adjust radio frequency to your desired station by using the “TUNING” control.
4. Adjust the “VOLUME” control to the desired level.
FM / FM-STEREO RECEPTION
- Set the “BAND” selector to FM mode for MONO reception.
- Set the “BAND” selector to FM ST. mode for FM STEREO reception. The Stereo indicator light up
to show FM ST. mode.
RADIO OPERATION
E-5
FOR BETTER RECEPTIO
N
FM - This appliance has a FM antenna located at the rear cabinet. This wire is completely unraveled
and extended for better reception.
AM - This appliance is equipped with a built - in directional ferrite AM antenna. Rotate the appliance
to get better reception.
CD / MP3 OPERATION
E-6
GENERAL OPERATI
ON
PLAY / PAUSE Press to start playing CD / MP3 disc.
Press again to stop playing CD / MP3 operation temporarily.
Press again to resume playback.
SKIP + & Press to go to the next track or back to the previous track.
SKIP - Press and hold while playing until you find the point of the sound.
STOP Press to stop all CD / MP3 operation.
PLAYBACK
1. Set the “FUNCTION” selector to “CD / MP3” mode.
2. Open the CD door and place a CD / MP3 disc with the label up in the CD compartment.
3. Close the CD door.
4. Focus search is performed if disc is inside.
For CD disc - Total number of tracks is read and appears on the display.
For MP3 disc - “MP3” appears on the display
.
5. Press the “PLAY / PAUSE” button to start playing CD / MP3 disc.
6. Adjust the “VOLUME” control to the desired level.
7. Press the “PLAY / PAUSE” button again when you want to stop playback temporarily.
8. Press the “STOP” button when finished.
Note. When playing MP3 discs, the disc will occasionally stop, this is normal, as the MP3 system of
operation is different from normal CD’s
CLOCK SETTING
OTHER FEATURES
MODE
Press the “MODE” button before or during playing CD / MP3 disc,
each press switches the mode function as follows:
1 - REPEAT 1
2 - REPEAT ALBUM ( *MP3 ONLY )
3 - REPEAT ALL
4 - RANDOM
5 - NORMAL PLAYBACK
REPEAT 1
REP
REP
ALBUM
REP
ALL
REPE
AT
ALB
UM
REPE
AT
ALL
NORMAL
PLAYBA
CK
RAND
RAND
OM
CD / MP3 OPERATION
PROGRAM
Be sure to press the “STOP” button before use.
1. Press the “PROGRAM” button, the display will show “P01” and flash.
2. Select desired track by using the “SKIP +” or “SKIP -” button. (You may select a desired album
by pressing the “ALBUM” button).
3. Press the “PROGRAM” button again to confirm desired track into the program memory.
4. Repeat step 2 and 3 to enter additional tracks into the program memory.
5. When all the desired tracks have been programmed, press the “PLAY / PAUSE” button to play the
disc in the order you have programmed.
6. Press the “STOP” button twice to terminate programmed playback.
E-7
1. Press the “TIME SET” button. (Do not release the “TIME SET” button during time setting).
2. Press the “HOUR” button to set Hours
3. Press the “MINUTE” button to set Minutes.
4. Release the Time Set button to start the clock.
Note this is a 12 Hr clock
FAULT GUIDE
Should you experience any problems please see guide below before cslling the help line.
E-8
If you are still having difficulty please call the Technical help line. Ring 01422 263313 (Normal
rates apply).
Opening hours Mon-Fri 8 am – 8pm. Sat 9 am – 4pm. Sun 11am – 4pm “Bank
holidays
as Sun”. or www.ekey.co.uk (24Hr)
Symptom
Possible Cause Remedy
Dead No operation No power to player
Ch
eck the power plug is in
firmly
and connected to a
power
supply.
No
radio operations but Led lit Function switch set to CD Switch to Radio or place a disc
into
the player
No
or noisy radio stations on
MW
Poor signal
Rotate
the case of the radio as
the
internal aerial is
directional.
The wire arerial is
not used on AM
No
or noisy stations on FM Poor signal Extend the wire aerial
Dirty
or damaged discs.
Carefully
clean the disc and
place
in the player label side
up.
Not
playing discs
Dirty
Laser lens Carefully clean the laser lens
with a cotton bud.
Batteries exhausted. Replace batteries.No, or intermittent Remote
control
operation.
Objects
in path of Infra red
signal.
Clear I/R path
IMPORTANT
If the mains plug requires replacement, please follow the following instructions.
DO NOT CONNECT THE CENTRE PIN (EARTH).
Connect the Blue wire to the (N) terminal ( this may be
coloured blue).
Connect the Brown wire to the (L) terminal adjacent to
the fuse ( this may be coloured brown).
This appliance must have a 3A fuse fitted.
E-9
ON HANDLING DISCS ON CLEANING DISCS
Do not touch the playback side of the disc.
Do not attach paper or tape to disc.
Fingerprints and dust on the disc cause sound
distortion and skipping of tracks. Wipe the disc
from the centre outwards with a soft cloth.
If you can not wipe off the dust with a soft cloth,
wipe the disc lightly with a slightly moistened soft
cloth and finish with a dry cloth.
Do not use any type of solvent such as thinner,
benzine, commercially available cleaners or anti-
static spray for vinyl Lps. It may damage the disc.
SPECIFICATIONS
Power Supply : 230V – 50Hz
Power Consumption : 13W
Output Power (RMS) : 2 X 2W
Terminal impedence : Speaker X 4ohms
Unit Dimension [main] : 204(L) x 135(W) x 188(H)mm
Unit Dimension [speaker] : 150(L) x 120(W) x 183(H)mm
Net Weight : 3.2kgs
Gross Weight : 3.8kgs
Tuning Frequency: AM: 540-1600KHz
FM : 88-108MHz
DC Operation : 9V ( 6 x UM-2)
Disc operation : CD and MP3. 7cm 12cm
discs
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
Akura APTMP221DR is a versatile 3-in-1 device that combines a radio, CD player, and MP3 player. You can listen to your favorite FM stations or CDs, or play MP3 files from a USB drive or SD card. The device also has a built-in clock and alarm so you can wake up to your favorite music. With its compact size and stylish design, the Akura APTMP221DR is the perfect addition to any home or office.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Coopers 8830 Operating instructions
-
Blaupunkt B 5 BL Owner's manual
-
Sencor SPT 3310 User manual
-
Samsung MM-ZC9 User manual
-
Panasonic RXVT80 Operating instructions
-
Sytech SY2022RJ Owner's manual
-
Sencor SPT 3800 User manual
-
-
Sony CMT-NE5 User manual
-