JUNG A1561.07BFFKOANM Operating instructions

Brand: JUNG

Model: A1561.07BFFKOANM

Type: Operating instructions

Light Management Radio-control pushbutton and pilot lamp

Ref.-no.: ..1561.07FKO..

Operating Instructions

Radio-control pushbutton and pilot lamp

1. Function

The radio-contol pushbutton permits radio-controlled or manual switching

and dimming of lamps.The starting brightness can be stored in the device

as memory brightness. The pushbutton with radio-control receiver is

plugged onto one of the following inserts:

 Universal touch dimmer 1254 UDE

 Standard touch dimmer 1225 SDE

 Relay insert single-channel 1201 URE

 Relay insert two-channel 1202 URE

 Tronic switching insert 1254 TSE

 LV triac switching insert 1244 NVSE

 Touch control unit 1240 STE

Relay insert with potential-free contact 1201-1 URE After reception of a

data telegram from a programmed radio-control detector and

corresponding darkness, the radio-contol pushbutton is switched on for

about 1 minute with the preset memory brightness. The radio-contol

pushbutton can be programmed to identify up to 30 radio channels.

Lightscapes

The radio-contol pushbutton can be included in up to five lightscapes

which are activated with the corresponding radio-control transmitters (e.g.

hand-held transmitter ‘Komfort’) and stored. The desired lightscape key

must be programmed beforehand into the radio-contol pushbutton.

All-ON / All-OFF

The programming of a radio channel (e.g. hand-held transmitter

‘Komfort’) always includes the simultaneous and automatic storage of the

functions of the All-ON or All-OFF key.The All-ON or All- OFF key of a

radio-control transmitter switches the load connected to the switching

actuator on or off.

Light control

In combination with a programmed radio-control presence detector, the

radio-contol pushbutton can be used for lighting control functions. For

more information, refer to the operating instructions of the radio presence

detector.

Stand: Mai-07 325 276 53

Light Management Radio-control pushbutton and pilot lamp

Ref.-no.: ..1561.07FKO..

Important

The present instructions describe the functions of the radio-control

pushbutton without lighting control. More information on light control with

a presence detector is set out in the operating instructions for these

devices.

WARNING!

Caution: The installation and assembly of electrical equipment may

only be performed by a skilled electrician.

2. Fitting

The radio-control pushbutton can only be operated in conjunction with the

inserts listed under ‘Functions’. Connection and fitting are described in

the operating instructions of the insert.

Procedure

1. Install the selected insert (1) in a flush-mounting box (deep model

recommended), the connecting terminals of the insert pointing

downwards.

2. Plug the radio-control pushbutton (2) together with frame (3) onto

the insert while the mains voltage is disconnected.

L The distance from electrical appliances (e.g. microwave oven, hi-fi and

TV sets) must be at least 0.5 m.

L To prevent saturation of the radio receiver (actuator), the radiocontrol

pushbutton must be at least 1 m away from the nearest transmitter.

Learning a Radio Transmitter

During programming of a transmitter, the sensitivity of a radiocontrol

receiver is reduced to a range of approx. 5 m. The distance between the

radio-control pushbutton and the transmitter to be programmed should be

between 0.5 m and 5 m.

Procedure

1. Switch off the load connected to the radio-control pushbutton by a brief

depression (< 0,4 s) of any of the two pushbutton rockers.

2. Depress both rockers of the radio-control pushbutton at the same time

for abt. 4 seconds (fig. B: double-sided operation) to switch over to the

programming mode. The LED blinks for abt. 1 min (Fig. C). The radio

pushbutton is then in the programming mode.

Light Management Radio-control pushbutton and pilot lamp

Ref.-no.: ..1561.07FKO..

> 4 s

Prog

1 min

3. Send a radio telegram from the selected transmitter (fig. D); see

„Radio-control transmitter“ operating instructions:

Programming a channel

Depress the channel key for more than 1 second.

Programming a lightscape key

Depress the lightscape key for more than 3 seconds.

Programming a detector

Remove the battery for about 2 minutes from the detector. Put the the

battery back in place and make a movement inside the detection range of

the detector within the next 10 minutes.

Programming a presence detector

Remove the battery(ies) for about 2 minutes from the transmitter. After

putting the battery back in place, the device starts transmitting

programming telegrams for about 30 s.

L It is not possible to program a combination consisting of presence-

control detector and detector.

4. The radio pushbutton confirms the storage by switching on the

LED permanently

Prog

1 min

5. The programming mode ends automatically after about 1 minute or

can be terminated by a short depression of the programming key. The

radio-control pushbutton is then again in the normal operating mode.

L When all 30 memories are occupied, it is necessary to delete an

already stored transmitter before a new one can be programmed.

Light Management Radio-control pushbutton and pilot lamp

Ref.-no.: ..1561.07FKO..

L The programming of a radio channel (e.g. hand-held transmitter

‘Komfort’) always includes the simultaneous and automatic storage of

the functions of the All-ON or All-OFF key.

Deleting a radio-control transmitter

A radio-control-transmitter in the pushbutton’s memory is deleted when

the same transmitter is programmed again into the memory (see above).

All channels and lightscape keys must be deleted one by one. Successful

deletion is indicated by the LED blinking fast (fig. F).

Prog

1 min

Deleting all radio-control transmitters

It is possible to delete all transmitters in the radio pushbutton. In this

case, the radio pushbutton is reset to the state as delivered.

1. Depress both faces of the radio pushbutton at the same time for

about. 20 s (Fig.. G: full-faced operation). After abt. 4 s, the LED

starts blinking (cf. Fig. C). After 20 s the LED emits brief flashes of

light for abt. 6 s.

> 20 s

2. Release the radio pushbutton briefly during these 6 s and press once

again both sides for about 1 s to start the deleting procedure.

3. During the deletion, the LED is illuminated. Successful deletion of all

radio transmitters is then indicated by a fast blinking LED (cf. Fig. F).

The LED is extinguished after abt. 1 min or after a brief press on the

button.

3. Operation

The radio-control pushbutton has an upper and a lower rocker. The

operation distinguishes between a short and a long depression of the

pushbutton rocker:

Light Management Radio-control pushbutton and pilot lamp

Ref.-no.: ..1561.07FKO..

Short depression of pushbutton (< 0,4 s)

The lights are switched on (on with memory brightness) or off. When the

lights are on, the LED is illuminated.

Short depression of pushbutton (> or = 0,4 s)

When the radio-control pushbutton is attached to an insert permitting the

dimming function, the brightness of the lamps connected can be

increased (upper rocker) and decreased (lower rocker) by a long

depression of the pushbutton rockers.

L To switch on the lamps at mimimum brightness, depress the lower

rocker for more than 0,4 seconds when the lamps are off.

3.1. Memory-function

The selected brightness level can be stored as memory value in the

radio-control pushbutton. A brief depression of the pushbutton recalls the

memory brightness level as the starting brightness of the lamp.

Storing the memory value

1. Select the desired brightness level for the lamps.

2. Depress both rockers at the same time for at least 4 seconds

(fig.I). This is confirmed by a soft-start, i.e. the lighting is shut off

briefly and then increased in brightness up to the stored memory

value.

L In as-delivered condition, the memory value is set to maximum

brightness.

L A saved memory value is not lost after a mains failure.

3.2. Lightscape

Before storing or recalling a lightscape, the lightscape key of the radio-

control transmitter must be programmed into the radio-control pushbutton

(see „Programming of a radio transmitter“). The data pertaining to a

lightscape (brightness of lamp) can then be stored in the radio-control

pushbutton. A lightscape can be changed at any time by storing it again.

Storing a lightscape

1. Select the desired brightness of the lamp.

2. Depress the lightscape key of the radio transmitter for at least 3

seconds. The old lightscape will at first be recalled (keep key

depressed). The new lightscape will activated and stored only after

about 3 seconds.

Light Management Radio-control pushbutton and pilot lamp

Ref.-no.: ..1561.07FKO..

4. Radio Transmission

Radio transmission takes place on a non-exclusive path. Therefore,

interference cannot be excluded. This type of radio transmission is not

suitable for safety applications such as emergency stops or emergency

calls. The range of a radio-control system depends on transmitter power,

receiver characteristics, air humidity, fitting height and building conditions.

Fig. I illustrates the penetration of building materials by radio waves:

Dry material Permeability

Timber, gypsum, gypsum-plasterboards approx. 90 %

Brickwork, particle boards approx. 70 %

Reinforced concrete approx. 30 %

Metal, metal grating, aluminium lamination approx. 10 %

Rain, snow approx. 0 - 40 %

Radio operation

 The inter-connection of this radio system with other

communication networks must comply with national legislation.

 This radio system must not be used for communication beyond

property boundaries.

 If utilized in conformity with its designated use, this unit fulfills the

requirements of the R&TTE Directive (1999/5/EC). The complete

declaration of conformity can be found in the Internet under:

www.jung.de/ce

The radio-control pushbutton may be operated in all countries of the EU

and the EFTA.

5. Specifications

Power supply : from flush-mounting insert

Receive frequency : 433,42 MHz, ASK

Number of radio channels : 30

Temperature range : approx. 0 °C ... +55 °C

Technical specifications subject to change.

Light Management Radio-control pushbutton and pilot lamp

Ref.-no.: ..1561.07FKO..

6. Guarantee

Our products are under guarantee within the scope of the statutory

provisions.

Please return the unit postage paid to our central service

department giving a brief description of the fault:

ALBRECHT JUNG GMBH & CO. KG

Service-Center

Kupferstr. 17-19

D-44532 Lünen

Service-Line: +(49) 23 55 . 80 65 51

Telefax: +(49) 23 55 . 80 61 65

E-Mail: [email protected]

General equipment

Service-Line: +(49) 23 55 . 80 65 55

Telefax: +(49) 23 55 . 80 62 55

E-Mail: [email protected]

KNX equipment

Service-Line: +(49) 23 55 . 80 65 56

Telefax: +(49) 23 55 . 80 62 55

E-Mail: [email protected]

The

-Sign is a free trade sign addressed exclusively to the

authorities and does not include any warranty of any properties.

JUNG A1561.07BFFKOANM Operating instructions

JUNG A1561.07BFFKOANM Operating instructions

JUNG A1561.07BFFKOANM Operating instructions

Related papers

Other documents