JUNG 1223NE Operating instructions

Type
Operating instructions

JUNG 1223NE: Enhancing Your Light Management

The JUNG 1223NE 3-wire extension unit insert is designed to extend the functionality of compatible JUNG main units, providing intelligent light control capabilities. It can be used in conjunction with presence detector or automatic switch attachments to create a motion-activated lighting system.

This extension unit transmits a light-independent switching signal to the main unit upon detecting movement, allowing for automated lighting control. It supports up to 5 parallel extensions when controlled by a universal dimmer and up to 10 extensions when controlled by other flush-mounting inserts.

JUNG 1223NE: Enhancing Your Light Management

The JUNG 1223NE 3-wire extension unit insert is designed to extend the functionality of compatible JUNG main units, providing intelligent light control capabilities. It can be used in conjunction with presence detector or automatic switch attachments to create a motion-activated lighting system.

This extension unit transmits a light-independent switching signal to the main unit upon detecting movement, allowing for automated lighting control. It supports up to 5 parallel extensions when controlled by a universal dimmer and up to 10 extensions when controlled by other flush-mounting inserts.

Light Management 3-wire extension unit insert
Ref.-no.: 1223 NE
Stand: Jul-08 325 351 13
Operating Instructions
3-wire extension unit insert
1. Safety instructions
Attention: Electrical equipment must be installed and fitted by
qualified electricians only. To prevent electric shocks, disconnect
the power supply before working on the device (by cutting out the
circuit breaker). Non-observance of the installation instructions may
causefire or other hazards.
2. Function
3-wire extension unit as a 3-wire extension unit (active extension) for
presence detectors or automatic switches. The extension unit can only be
used in conjunction with the presence detector attachment or automatic
switch attachment. Other attachments than those specified do not yield
any meaningful functions. In conjunction with the presence detector
attachment or the automatic switch attachment unit, the 3-wire extension
unit transmits a lightindependent switching signal to the main unit when a
movement is detected. The signals are processed in the attachment
(presence detector or automatic switch attachment) of the main unit.
Inserts that can be used for the main unit: Universal dimmer, LV dimmer
Triac-switching insert, Tronic-switching insert Relay insert, 2-channel
relay insert
Note: The extension unit is not suitable for direct switching of loads.
The extension unit must not be used in conjunction with more than one
main unit.
Light Management 3-wire extension unit insert
Ref.-no.: 1223 NE
2
3. Fitting instructions
The extension unit insert (1) is installed in a DIN 49073 flushmounting
box (see fig. A).
The connection terminals of the insert must be at the bottom (wall-
mounting). The attachment (2) is plugged onto the insert (1) together with
frame (3). The electrical contact with the insert is ensured by plug (4). B.
Connection diagram see fig. B.
Main unit (5).
Extension unit (6).
Further extension units (7).
Load (8)
Light Management 3-wire extension unit insert
Ref.-no.: 1223 NE
3
4. Technical data
Nominal voltage :AC 230 V ~, 50 / 60 Hz
N conductor required
Connection :to main unit (with presence detector
or automatic-switch attachment)
The number of parallel extensions is limited to
5 at maximum :when controlled from a universa
dimmer
10 at maximum :when controlled from other flush-
mounting inserts
Length of line :max. 100 m
5. Guarantee
Our products are under guarantee within the scope of the statutory
provisions.
Please return the unit postage paid to our central service
department giving a brief description of the fault:
ALBRECHT JUNG GMBH & CO. KG
Service-Center
Kupferstr. 17-19
D-44532 Lünen
Service-Line: +(49) 23 55 . 80 65 51
Telefax: +(49) 23 55 . 80 61 65
General equipment
Service-Line: +(49) 23 55 . 80 65 55
Telefax: +(49) 23 55 . 80 62 55
KNX equipment
Service-Line: +(49) 23 55 . 80 65 56
Telefax: +(49) 23 55 . 80 62 55
The
-Sign is a free trade sign addressed exclusively to the
authorities and does not include any warranty of any properties.
  • Page 1 1
  • Page 2 2
  • Page 3 3

JUNG 1223NE Operating instructions

Type
Operating instructions

JUNG 1223NE: Enhancing Your Light Management

The JUNG 1223NE 3-wire extension unit insert is designed to extend the functionality of compatible JUNG main units, providing intelligent light control capabilities. It can be used in conjunction with presence detector or automatic switch attachments to create a motion-activated lighting system.

This extension unit transmits a light-independent switching signal to the main unit upon detecting movement, allowing for automated lighting control. It supports up to 5 parallel extensions when controlled by a universal dimmer and up to 10 extensions when controlled by other flush-mounting inserts.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI