Above All ABWP20LED40DS User manual

Brand: Above All

Model: ABWP20LED40DS

Category: Motorcycle Accessories

Type: User manual

LED FULL CUTOFF WALL PACK

Instructions Manual

SUITABLE FOR MODEL

IMAGE MAY VARY FROM ACTUAL PRODUCT

SAFETY INSTRUCTION

MAINTENANCE CAUTION

READ CAREFULLY BEFORE INSTALLING FIXTURE. PLEASE KEEP THIS MANUAL FOR FUTURE USING.

Fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding

is required for safety.

THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICATION CODE BY A PERSON

FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.

MAKE CERTAIN POWER OFF BEFORE INSTALLING OR MAINTAINING FIXTURE.

CHECK THAT VOLTAGE IS COMPATIBLE WITH FIXTURE DRIVER, USE APPROVED CONNECTORS FOR

ALL ELECTRICAL CONNECTIONS.

1. Review the wire connection before beginning, and make sure fixture is grounded properly.

2. For lighting controls, using functioning correctly.

3. Turn power off and wait for fixture cooling to operate.

4. Maintenance must be done by professionals.

WIRE CONNECTION

FOR 20W/30W/ 38W FULL CUTOFF WALL PACK WITH

PHOTOCELL

FOR 52W FULL CUTOFF WALL PACK WITH PHOTOCELL

Led Board DC IN+ Led Board DC IN-

BLACKRED

WAGO

RED

BLACK

AC INAC IN

PHOTOCELL

GROUND IN

BLACK

WHITE

RED

WAGO

RED

BLACK

POWER OUT(DC) POWER IN(DC)

POWER SUPPLY

RED

BLACK

WHITE

GREEN

BLACK

Led Board DC IN+ Led Board DC IN-

BLACKRED

AC INAC IN

PHOTOCELL

GROUND IN

WAGO

POWER SUPPLY

POWER OUT(DC) POWER IN(DC)

WAGO

BLACK

WHITE

RED

Universal voltage driver permits operation at 120 or

277V, 60Hz

Universal voltage driver permits operation at 120 or

277V, 60Hz

Add: 1501 Industrial Way N. Toms River, NJ 08755 Phone: 866-222-8866 E-mail: [email protected]

LED FULL CUTOFF WALL PACK

FOR 30W/ 38W FULL CUTOFF WALL PACK

Universal voltage driver permits operation at 120V

thru 277V,50/60Hz

FOR 20W FULL CUTOFF WALL PACK

Universal voltage driver permits operation at 120V

thru 277V,50/60Hz

FOR 52W FULL CUTOFF WALL PACK

Universal voltage driver permits operation at

120V thru 277V,50/60Hz

Ref#: 10050-21020

INSTALLATION

Install the fixture as the picture shows.(Installation height

≥ 6.6ft.)

≥6.6 FT.

GROUND

WALL

FIXED HOLE

CLIP

SCREW

BASE COVER

TOP COVER

WARRANTY

LED

BOARD

GROUND GROUND

ACN(WHITE)

ACL(BLACK)

POWER

RED(+)

RED

(DC+)

BLACK

(DC-)

BLACK(-)

WAGO

GROUND GROUND

LED

BOARD

RED(+)

RED

(DC+)

BLACK

(DC-)

BLACK(-)

POWER

DIMMER

ACN(WHITE)

ACL(BLACK)

DIM+(PURPLE)

DIM-(GRAY)

VAUX/12V

(YELLOW)

WAGO

GROUND

DIM+(BLUE)

RED(+)

RED

(DC+)

BLACK

(DC-)

BLACK(-)

DIM-(WHITE)

DIMMER

ACN(BLUE)

GREEN/YELLOW

ACL(BROWN)

LED

BOARD

POWER

Instructions Manual

1.Cut off the power before installation.

2.Unscrew the two fixed screws,unload the top cover, and fix

the base cover to the wall.

3. Pass the three phase cable by the base or 1/2NPT hole,

and connect it with AC driver and ground wire.

4. Connect DC wire from the reflector hole with DC LED

board. (Caution: red to red, black to black)

5.Close the cover, and tighten the two fixed screws.

6.Choose the suitable place to install, connect the power to

lighten up.(Finish the installation)

LIMITED FIVE-YEAR WARRANTY. Should this product fail to perform satisfactorily due to a defect or poor workmanship

within five years from the date of purchase, return it to the place of purchase and it will be replaced, free of charge.

Incidental or consequential damages are excluded from the warranty.

Add: 1501 Industrial Way N. Toms River, NJ 08755 Phone: 866-222-8866 E-mail: [email protected]

Above All ABWP20LED40DS User manual

Brand: Above All

Model: ABWP20LED40DS

Category: Motorcycle Accessories

Type: User manual

Download PDF

report

Above All ABWP20LED40DS User manual

Above All ABWP20LED40DS User manual

Related papers

Other documents