WAGO 16-channel, 24VDC User manual

Pos: 2 /Dokumentation allgemein/Einband/Einband Handbuch - Deckbl at t oh ne V aria nt enfel d (S ta ndar d) @ 9 \mod_1285229289866_0.docx @ 64941 @ @ 1

Manual

WAGO-I/O-SYSTEM 750

16DO 24V DC 0.5A, ribbon cable, low-

side

switching

750-1501

16-

Channel Digital Output Module 24 VDC, Ribbon

Cable, Low-side Switching

Version 1.1.0

Pos: 3 /A lle Ser ien ( All ge mein e M odul e)/ Hin weise zur Dokumentation/Impressum für Standardhandbücher - allg. A nga ben, Ansc hrift en, Tel efonn ummer n und E-M ail-A dres sen @ 3\mod_1219151118203_21.docx @ 21060 @ @ 1

2 WAGO-I/O-SYSTEM 750

750-1501 16DO 24V DC 0.5A, ribbon cable, low-side switching

Manual

Version 1.1.0

WAGO Kontakttechnik GmbH & Co. KG

Hansastraße 27

D-32423 Minden

Phone: +49 (0) 571/8 87 – 0

Fax: +49 (0) 571/8 87 – 1 69

E-Mail: [email protected]

Web: http://www.wago.com

Technical Support

Phone: +49 (0) 571/8 87 – 5 55

Fax: +49 (0) 571/8 87 – 85 55

E-Mail: [email protected]

Every conceivable measure has been taken to ensure the accuracy and

completeness of this documentation. However, as errors can never be fully

excluded, we always appreciate any information or suggestions for improving the

documentation.

E-Mail: [email protected]

We wish to point out that the software and hardware terms as well as the

trademarks of companies used and/or mentioned in the present manual are

generally protected by trademark or patent.

=== Ende der Lis te f ür T e xtmar ke Ei nb and _vor ne = ==

WAGO-I/O-SYSTEM 750 Table of Contents 3

750-1501 16DO 24V DC 0.5A, ribbon cable, low-side switching

Manual

Version 1.1.0

Pos: 5 /D ok ument ati on al lg em ein/V erz eic hni sse /Inh alts ver zei chni s - Ü bersc hrift oG und Ver zeich nis @ 3\ mod_1219151230875_21.docx @ 21063 @ @ 1

Table of Contents

1 Notes about this Documentation ................................................................. 5

1.1 Validity of this Documentation ................................................................. 5

1.2 Copyright ................................................................................................... 5

1.3 Symbols ..................................................................................................... 6

1.4 Number Notation ....................................................................................... 8

1.5 Font Conventions ...................................................................................... 8

2 Important Notes ........................................................................................... 9

2.1 Legal Bases ............................................................................................... 9

2.1.1 Subject to Changes ............................................................................... 9

2.1.2 Personnel Qualifications ....................................................................... 9

2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with Underlying

Provisions ............................................................................................. 9

2.1.4 Technical Condition of Specified Devices ......................................... 10

2.2 Safety Advice (Precautions) .................................................................... 11

3 Device Description ..................................................................................... 13

3.1 View ........................................................................................................ 15

3.2 Connectors ............................................................................................... 16

3.2.1 Data Contacts/Internal Bus ................................................................. 16

3.2.2 Ribbon Cable and CAGE CLAMP

®

Connectors ............................... 17

3.3 Display Elements .................................................................................... 18

3.4 Operating Elements ................................................................................. 18

3.5 Schematic Diagram ................................................................................. 19

3.6 Technical Data ........................................................................................ 20

3.6.1 Device ................................................................................................. 20

3.6.2 Communication .................................................................................. 20

3.6.3 Supply ................................................................................................. 20

3.6.4 Outputs ............................................................................................... 20

3.6.5 Connection Type ................................................................................ 21

3.6.6 Climatic Environmental Conditions ................................................... 21

3.7 Approvals ................................................................................................ 22

3.8 Standards and Guidelines ........................................................................ 23

4 Mounting ..................................................................................................... 24

4.1 Mounting Sequence ................................................................................. 24

4.2 Inserting and Removing Devices ............................................................ 25

4.2.1 Inserting the I/O Module .................................................................... 25

4.2.2 Removing the I/O Module .................................................................. 26

5 Connect Devices ......................................................................................... 27

5.1 Connecting a Conductor to the CAGE CLAMP

®

................................... 27

6 Process Image ............................................................................................. 28

7 Accessories .................................................................................................. 29

8 Using Interference-Free I/O Modules in Safety Related Applications . 30

8.1 Important Notes ....................................................................................... 31

4 Table of Contents WAGO-I/O-SYSTEM 750

750-1501 16DO 24V DC 0.5A, ribbon cable, low-side switching

Manual

Version 1.1.0

8.2 Connecting the I/O Module to Safety Switching Devices or Safety

Modules ................................................................................................... 32

8.2.1 General Structure of a Potential Group .............................................. 32

8.2.2 Examples of Connection..................................................................... 33

9 Use in Hazardous Environments .............................................................. 34

9.1 Marking Configuration Examples ........................................................... 35

9.1.1 Marking for Europe According to ATEX and IEC-Ex ...................... 35

9.1.2 Marking for America According to NEC 500 .................................... 40

9.2 Installation Regulations ........................................................................... 41

9.2.1 Special Conditions for Safe Use (ATEX Certificate TÜV 07 ATEX

554086 X) ........................................................................................... 42

9.2.2 Special Conditions for Safe Use (ATEX Certificate TÜV 12 ATEX

106032 X) ........................................................................................... 43

9.2.3 Special Conditions for Safe Use (IEC-Ex Certificate TUN 09.0001 X)44

9.2.4 Special Conditions for Safe Use (IEC-Ex Certificate IECEx TUN

12.0039 X) .......................................................................................... 45

9.2.5 Special Conditions for Safe Use According to ANSI/ISA 12.12.01 .. 46

List of Figures ...................................................................................................... 47

List of Tables ........................................................................................................ 48

=== Ende der Lis te f ür T e xtmar ke V erz eic hnis _vor ne ===

WAGO-I/O-SYSTEM 750 Notes about this Documentation 5

750-1501 16DO 24V DC 0.5A, ribbon cable, low-side switching

Manual

Version 1.1.0

Pos: 7 /A lle Ser ien ( All ge mein e M odul e)/ Über sc hrif ten für all e Ser ie n/Hi nwei se zur D o kume nt ation /Hi nw eise zu dies er D o kume ntati on - Ü ber schr if t 1 @ 4\ mod_1237987661750_21.docx @ 29029 @ 1 @ 1

1 Notes about this Documentation

Pos: 8 /A lle Ser ien ( All ge mein e M odul e)/ Hin weis e z ur D oku men tati on/H i nweis e/Hi n weis : D okum ent atio n a ufbe wahr e n @ 4 \mod_1237987339812_21.docx @ 29026 @ @ 1

Always retain this documentation!

This documentation is part of the product. Therefore, retain the documentation

during the entire service life of the product. Pass on the documentation to any

subsequent user. In addition, ensure that any supplement to this documentation is

included, if necessary.

Pos: 9 /A lle Ser ien ( All ge mein e M odul e)/ Über sc hrif ten für all e Ser ie n/Hi nwei se zur D o kume nt ation /Gül tig keit sber eic h - Üb ersc hrif t 2 @ 1 2\mod_1338912448776_21.docx @ 96469 @ 2 @ 1

1.1 Validity of this Documentation

Pos: 10 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Hi n weis e zur D okum ent ati on/G ülti gkei ts berei c h/Gül tig kei tsber ei ch D oku men tat ion Bus kle mme 75 0-xxxx, o hne Var ia nten ang abe @ 14 \mod_1358944037947_21.docx @ 109346 @ @ 1

This documentation is only applicable to the I/O module 750-1501

(16DO 24V DC 0.5A, ribbon cable, low-side switching).

Pos: 11 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Hi n weis e zur D okum ent ati on/Hi nw eise /Ac htu ng: H in weis zur D oku ment ati on B uskl e mmen 750- xxxx @ 4\mod_1237986979656_21.docx @ 29023 @ @ 1

The I/O module 750-1501 shall only be installed and operated according to the

instructions in this manual and in the manual for the used fieldbus

coupler/controller.

Consider power layout of the WAGO-I/O-SYSTEM 750!

In addition to these operating instructions, you will also need the manual for the

used fieldbus coupler/controller, which can be downloaded at www.wago.com.

There, you can obtain important information including information on electrical

isolation, system power and supply specifications.

Pos: 12 .1 /All e Seri en (All ge meine Mo dul e)/H in weis e zur D oku ment ati on/U rh eber sc hutz aus führ lic h @ 4\mod_1235565145234_21.docx @ 27691 @ 2 @ 1

1.2 Copyright

This Manual, including all figures and illustrations, is copyright-protected. Any

further use of this Manual by third parties that violate pertinent copyright

provisions is prohibited. Reproduction, translation, electronic and phototechnical

filing/archiving (e.g., photocopying) as well as any amendments require the

written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.

Non-observance will involve the right to assert damage claims.

Pos: 12.2 /Dokumentation allgemein/Gliederungselemente/---Seite nwechs el--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1

6 Notes about this Documentation WAGO-I/O-SYSTEM 750

750-1501 16DO 24V DC 0.5A, ribbon cable, low-side switching

Manual

Version 1.1.0

Pos: 12.3 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en f ür alle S erie n/Hi nwei se z ur Dok um enta tio n/S ymbol e - Ü bers chr ift 2 @ 1 3\mod_1351068042408_21.docx @ 105270 @ 2 @ 1

1.3 Symbols

Pos: 12 .4.1 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und so nsti ge H inw eis e/G efa hr/G efa hr: _War nu ng vor P ers onenschäden allgemein_ - Erläu terung @ 13\mod_1343309450020_21.docx @ 101029 @ @ 1

Personal Injury!

Indicates a high-risk, imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Pos: 12 .4.2 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und sonsti ge Hinw eise/ Gefa hr/Gef ahr: _ Warnu ng vor Per son enschä den durc h elek trisc hen Str om_ - Erläuterung @ 13\mod_1343309694914_21.docx @ 101030 @ @ 1

Personal Injury Caused by Electric Current!

Indicates a high-risk, imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Pos: 12 .4.3 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und so nsti ge H inw eis e/W arn ung/ War nung : _ War nu ng vor P erso nens ch äde n all ge mei n_ - Er läuterung @ 13\mod_1343309877041_21.docx @ 101035 @ @ 1

Personal Injury!

Indicates a moderate-risk, potentially hazardous situation which, if not avoided,

could result in death or serious injury.

Pos: 12 .4.4 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuterungen/Sicherheits- und so ns tige H in weis e/ Vorsi cht /V orsi cht: _ Warnu ng vor Pers on ensc hä den allg em ein _ - Erläuterung @ 13\mod_1343310028762_21.docx @ 101038 @ @ 1

Personal Injury!

Indicates a low-risk, potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

Pos: 12 .4.5 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und sonstige Hinweise/Achtung/Achtung: _Warnung vor Sachschäden allgemein_ - Erläuterung @ 13\mod_1343310134623_21.docx @ 101041 @ @ 1

Damage to Property!

Indicates a potentially hazardous situation which, if not avoided, may result in

damage to property.

Pos: 12 .4.6 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und sonstige Hinweise/Achtung/Achtung: _Warnung vor Sachschäd en durc h elektr ostat isch e Aufla dung_ - Erläuterung @ 13\mod_1343310227702_21.docx @ 101044 @ @ 1

Damage to Property Caused by Electrostatic Discharge (ESD)!

Indicates a potentially hazardous situation which, if not avoided, may result in

damage to property.

Pos: 12 .4.7 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und sonstige Hinweise/Hinweis/Hinweis: _Wichtiger Hinweis allgemein_ - Erläuterung @ 13\mod_1343310326906_21.docx @ 101047 @ @ 1

Important Note!

Indicates a potential malfunction which, if not avoided, however, will not result in

damage to property.

Pos: 12 .4.8 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und so nsti ge H inw eis e/I nfor mat ion/ Inf or matio n: _W eiter e Inf or mati on allg emei n_ - Erl äuter ung @ 13 \mod_1343310439814_21.docx @ 101051 @ @ 1

WAGO-I/O-SYSTEM 750 Notes about this Documentation 7

750-1501 16DO 24V DC 0.5A, ribbon cable, low-side switching

Manual

Version 1.1.0

Additional Information:

Refers to additional information which is not an integral part of this

documentation (e.g., the Internet).

Pos: 12.5 /Dokumentation allgemein/Gliederungselemente/---Seite nwechs el--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1

8 Notes about this Documentation WAGO-I/O-SYSTEM 750

750-1501 16DO 24V DC 0.5A, ribbon cable, low-side switching

Manual

Version 1.1.0

Pos: 12 .6 /All e Seri en (Allg emeine Modul e)/Hi nweis e zur Do kument ation /Zahl ensy steme @ 3\ mod_1221059454015_21.docx @ 21711 @ 2 @ 1

1.4 Number Notation

Table 1: Number Notation

Number Code

Example

Note

Decimal

100

Normal notation

Hexadecimal

0x64

C notation

Binary

'100'

'0110.0100'

In quotation marks, nibble separated with

dots (.)

Pos: 12 .7 /All e Seri en (Allg emeine Modul e)/Hi nweis e zur Do kument ation /Schr iftko nventi one n @ 3\mod_1221059521437_21.docx @ 21714 @ 2 @ 1

1.5 Font Conventions

Table 2: Font Conventions

Font Type

Indicates

italic

Names of paths and data files are marked in italic-type.

e.g.: C:\Program Files\WAGO Software

Menu

Menu items are marked in bold letters.

e.g.: Save

>

A greater-than sign between two names means the selection of a

menu item from a menu.

e.g.: File > New

Input

Designation of input or optional fields are marked in bold letters,

e.g.: Start of measurement range

“Value”

Input or selective values are marked in inverted commas.

e.g.: Enter the value “4 mA” under Start of measurement range.

[Button]

Pushbuttons in dialog boxes are marked with bold letters in square

brackets.

e.g.: [Input]

[Key]

Keys are marked with bold letters in square brackets.

e.g.: [F5]

Pos: 13 /D o kume ntati on allg emei n/ Gli eder ungs ele me nte /---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Important Notes 9

750-1501 16DO 24V DC 0.5A, ribbon cable, low-side switching

Manual

Version 1.1.0

Pos: 14 /Alle Ser ien (Al lge meine Mo dule)/ Über schrif ten für alle Ser ien/ Wichti ge Erlä uteru ngen/ Wich tige Er läuter ungen - Übersc hrift 1 @ 4\mod_1241428899156_21.docx @ 32170 @ 1 @ 1

2 Important Notes

Pos: 15.1 /All e Seri en ( All ge meine Do kum ente) ( All ge meine Mo dule) /Wi cht ige Erl äut eru nge n/Ei nl eit ung Wic htige Erl äut eru nge n @ 3 \mod_1221059818031_21.docx @ 21717 @ @ 1

This section includes an overall summary of the most important safety

requirements and notes that are mentioned in each individual section. To protect

your health and prevent damage to devices as well, it is imperative to read and

carefully follow the safety guidelines.

Pos: 15.2 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en f ür alle S erie n/Wi chti ge Erl äuter u ngenR ec htlic he Gr undl ag en - Üb ersc hrift 2 @ 3\ mod_1221060626343_21.docx @ 21726 @ 2 @ 1

2.1 Legal Bases

Pos: 15.3 /Alle Serien (Allgemeine Dokumente) (Allgemeine Module)/Wichtige Erläuterungen/Änderungsvorbehalt - Übers chri ft 3 un d In halt @ 3\mod_1221060036484_21.docx @ 21720 @ 3 @ 1

2.1.1 Subject to Changes

WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any

alterations or modifications that serve to increase the efficiency of technical

progress. WAGO Kontakttechnik GmbH & Co. KG owns all rights arising from

the granting of patents or from the legal protection of utility patents. Third-party

products are always mentioned without any reference to patent rights. Thus, the

existence of such rights cannot be excluded.

Pos: 15.4 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htige Erl äuter unge n/Pers onalq uali fikati onPer sonal qual ifika tion 750- xxxx - Ü bersc hrift 3 u nd Inhal t @ 3\mod_1224061208046_21.docx @ 24063 @ 3 @ 1

2.1.2 Personnel Qualifications

All sequences implemented on WAGO-I/O-SYSTEM 750 devices may only be

carried out by electrical specialists with sufficient knowledge in automation. The

specialists must be familiar with the current norms and guidelines for the devices

and automated environments.

All changes to the coupler or controller should always be carried out by qualified

personnel with sufficient skills in PLC programming.

Pos: 15.5 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htige Erl äuter unge n/Bes timmu ngsg emäße V erwe ndung Besti mmung sgemä ße Verw endung 750-xxxx - Über schr if t 3 und I nhal t @ 3\ mod_1224064151234_21.docx @ 24070 @ 3 @ 1

2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with

Underlying Provisions

Fieldbus couplers, fieldbus controllers and I/O modules found in the modular

WAGO-I/O-SYSTEM 750 receive digital and analog signals from sensors and

transmit them to actuators or higher-level control systems. Using programmable

controllers, the signals can also be (pre-) processed.

The devices have been developed for use in an environment that meets the IP20

protection class criteria. Protection against finger injury and solid impurities up to

12.5 mm diameter is assured; protection against water damage is not ensured.

Unless otherwise specified, operation of the devices in wet and dusty

environments is prohibited.

Operating the WAGO-I/O-SYSTEM 750 devices in home applications without

further measures is only permitted if they meet the emission limits (emissions of

interference) according to EN 61000-6-3. You will find the relevant information

in the section “Device Description” > “Standards and Guidelines” in the manual

for the used fieldbus coupler/controller.

10 Important Notes WAGO-I/O-SYSTEM 750

750-1501 16DO 24V DC 0.5A, ribbon cable, low-side switching

Manual

Version 1.1.0

Appropriate housing (per 94/9/EG) is required when operating the WAGO-I/O-

SYSTEM 750 in hazardous environments. Please note that a prototype test

certificate must be obtained that confirms the correct installation of the system in

a housing or switch cabinet.

Pos: 15.6 /All e Seri en ( All ge meine Do kum ente) ( All ge meine Mo dule) /Wi cht ige Erl äut eru nge n/T echni sc her Zus tan d d er G erä te - Ü bersc hrift 3 und Inhalt @ 3\mod_1221060446109_21.docx @ 21723 @ 3 @ 1

2.1.4 Technical Condition of Specified Devices

The devices to be supplied ex works are equipped with hardware and software

configurations, which meet the individual application requirements. WAGO

Kontakttechnik GmbH & Co. KG will be exempted from any liability in case of

changes in hardware or software as well as to non-compliant usage of devices.

Please send your request for modified and new hardware or software

configurations directly to WAGO Kontakttechnik GmbH & Co. KG.

Pos: 15.7 /Dokumentation allgemein/Gliederungselemente/---Seite nwechs el--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Important Notes 11

750-1501 16DO 24V DC 0.5A, ribbon cable, low-side switching

Manual

Version 1.1.0

Pos: 15 .8 /All e Seri en (Allg emeine Modul e)/Ü berschr ifte n für alle S erie n/Wich tige Er läuter ung enSic herhei tshi nweis e - Übers chrif t 2 @ 6\mod_1260180299987_21.docx @ 46724 @ 2 @ 1

2.2 Safety Advice (Precautions)

Pos: 15.9 /All e Seri en ( All ge meine Do kum ente) ( All ge meine Mo dule) /Wi cht ige Erl äut eru nge n/Si cher hei ts hin weis e/Ei nl eitu ng Sich erh eitshi nweis e Hard ware @ 6\mod_1260180170493_21.docx @ 46720 @ @ 1

For installing and operating purposes of the relevant device to your system the

following safety precautions shall be observed:

Pos: 15.1 0. 1 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /G efahr /G efahr : N ich t an G erät en unter Sp ann ung arbei te n! @ 6\ mod_1260180365327_21.docx @ 46727 @ @ 1

Do not work on devices while energized!

All power sources to the device shall be switched off prior to performing any

installation, repair or maintenance work.

Pos: 15.1 0. 2 /S erie 750 ( W AGO -I/O-SY ST EM) /Wic htig e Er l äuter ung en /Sic her hei ts- un d s onsti ge H in wei se/G ef ahr/ Gefa hr: Ei nbau 07 50- xxxx nur in Geh äusen, S chrä nken oder ele ktrisc hen Betr iebsr äume n! @ 6\mod_1260180556692_21.docx @ 46731 @ @ 1

Install the device only in appropriate housings, cabinets or in electrical

operation rooms!

The WAGO-I/O-SYSTEM 750 and its components are an open system. As such,

install the system and its components exclusively in appropriate housings,

cabinets or in electrical operation rooms. Allow access to such equipment and

fixtures to authorized, qualified staff only by means of specific keys or tools.

Pos: 15.1 0. 3 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /G efahr /G efahr : U nfal l verh ütung sv orsc hri ft en b each ten! @ 6\mod_1260180657000_21.docx @ 46735 @ @ 1

Pos: 15.1 0. 4 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /G efahr /G efahr : A uf normg er echt e n Ansc hlu ss ac hten! @ 6\mod_1260180753479_21.docx @ 46739 @ @ 1

Pos: 15.1 1. 1 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/A cht ung : Defek te oder besch ädigt e Gerät e austaus chen! @ 6\mod_1260180857358_21.docx @ 46743 @ @ 1

Replace defective or damaged devices!

Replace defective or damaged device/module (e.g., in the event of deformed

contacts), since the long-term functionality of device/module involved can no

longer be ensured.

Pos: 15.1 1. 2 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/A cht ung : G erät e vor kriec hen den und i sol ier e nden Sto ffen sch ütz en! @ 6\ mod_1260181036216_21.docx @ 46747 @ @ 1

Protect the components against materials having seeping and insulating

properties!

The components are not resistant to materials having seeping and insulating

properties such as: aerosols, silicones and triglycerides (found in some hand

creams). If you cannot exclude that such materials will appear in the component

environment, then install the components in an enclosure being resistant to the

above-mentioned materials. Clean tools and materials are imperative for handling

devices/modules.

Pos: 15.1 1. 3 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/A cht ung : Rei nig ung nur mi t zul äss ig en M at erial ien! @ 6\mod_1260181203293_21.docx @ 46751 @ @ 1

Clean only with permitted materials!

Clean soiled contacts using oil-free compressed air or with ethyl alcohol and

leather cloths.

Pos: 15.1 1. 4 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/A cht ung : K ein K ont a ktspra y verw end en! @ 6\ mod_1260181290808_21.docx @ 46755 @ @ 1

12 Important Notes WAGO-I/O-SYSTEM 750

750-1501 16DO 24V DC 0.5A, ribbon cable, low-side switching

Manual

Version 1.1.0

Do not use any contact spray!

Do not use any contact spray. The spray may impair contact area functionality in

connection with contamination.

Pos: 15.1 1. 5 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/A cht ung : V erpol ung ver mei de n! @ 6\m od_ 1260184045744_21.docx @ 46767 @ @ 1

Do not reverse the polarity of connection lines!

Avoid reverse polarity of data and power supply lines, as this may damage the

devices involved.

Pos: 15.1 1. 6 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erläuter ung en/Sic herh eits hinwei se/Ac htung /Acht ung: El ektr ostatis che Entl adu ng verm eide n! @ 6\mod_1260181364729_21.docx @ 46759 @ @ 1

Avoid electrostatic discharge!

The devices are equipped with electronic components that may be destroyed by

electrostatic discharge when touched. Please observe the safety precautions

against electrostatic discharge per DIN EN 61340-5-1/-3. When handling the

devices, please ensure that environmental factors (personnel, work space and

packaging) are properly grounded.

Pos: 16 /D o kume ntatio n allg emein/ Glie derung sele mente /---Seite nwe chsel --- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 13

750-1501 16DO 24V DC 0.5A, ribbon cable, low-side switching

Manual

Version 1.1.0

Pos: 17 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n für al le S eri en/G erä teb esc hrei bu ng/G erä tebe schr eib ung - Üb ersc hrift 1 @ 3\ mod_1233756084656_21.doc x @ 27096 @ 1 @ 1

3 Device Description

Pos: 18.1 /Serie 750 (WAGO-I/O-SYST EM)/ Ger ätebesc hrei bung/Ei nlei tung /Anw endung /DO/A nwen dung 7 50-x5xx DO @ 3\mod_1233764594468_21.docx @ 27120 @ @ 1

The 750-1501 (16DO 24V DC 0.5A, ribbon cable, low-side switching) Digital

Output Module transmits binary control signals from the automation device to the

connected actuators (e.g., solenoid valves, contactors, transmitters, relays or other

electrical loads).

Pos: 18.2 /Serie 750 (WAGO-I/O-SYST EM) /Ger äte besc hrei bu ng/Ei nlei tu ng/I/ O-B eschr ei bung/ DO/I /O-B eschr eibu ng 750-150x 16 DO 1-Leiter Stecker @ 3\mod_1233764653921_21.docx @ 27128 @ @ 1

The I/O module has 16 output channels and connects to electronic modules via

20-pin ribbon cable.

Pos: 18.3 /Serie 750 (WAGO-I/O-SYST EM) /Ger äte besc hrei bu ng/Ei nlei tu ng/I/ O-B esc hrei bung /Al lg emei n/Ver wei s a uf K api tel "A nsc hlüss e" @ 8\ mod_1276775378035_21.docx @ 57956 @ @ 1

The assignment of the connections is described in the “Connectors” section.

Pos: 18.4 /Serie 750 (WAGO-I/O-SYST EM) /Ger äte besc hrei bu ng/Ei nlei tu ng/I/ O-B esc hrei bung /Al lg emei n/Ver wei s a uf El e ktroni k baus tei ne al s Z ub ehör @ 4 \mod_1236063336171_21.docx @ 27953 @ @ 1

Suitable electronic modules are available as accessories from WAGO.

Pos: 18.5 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htige Erl äuter unge n/Sic herhei ts- und sonstige Hinweise/AchtungAchtung: DO Induktionsspannungsbegrenzung Elektronik @ 3\mod_1233815757507_21.docx @ 27153 @ @ 1

Limit all induced voltage!

The electronic components of the I/O module can be damaged by the induced

voltage produced when inductive loads are de-activated.

An appropriate protection circuit, e.g., a recovery diode, must be installed in

parallel to the load to limit this induced voltage.

Pos: 18.6 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htige Erl äuter unge n/Sic herhei ts- u nd so nsti g e Hin weis e/ Acht ung Acht ung : DO Üb erl asts chu tz - externe Sicherung @ 4\mod_1235739218312_21.docx @ 27940 @ @ 1

Provide for overload protection!

Overloading can damage the electronic components of the I/O module.

Install an appropriate fuse to protect the I/O module against overloading!

Pos: 18.7 /Serie 750 (WAGO-I/O-SYST EM) /Ger äte besc hrei bu ng/Ei nlei tu ng/I/ O-B eschr ei bung/ DO/I /O-B eschr eibu ng 750- x5xx DO LS S / negativsch alt end ( 0 V) @ 3\mod_1233817190023_21.docx @ 27163 @ @ 1

The I/O module outputs provide negative switching. If the signal status of an

output channel is at "high" the 0V potential for field power will be switched to the

appropriate output connection.

Pos: 18.8 /Serie 750 (WAGO-I/O-SYST EM) /Ger äte besc hrei bung /Ei nlei tung /LED -Anz eig e/ LED Z ust an d Sig nal @ 3\ mod_1233755258578_21.docx @ 27087 @ @ 1

A green LED indicates the switched status of each channel.

Pos: 18.9 /Serie 750 (WAGO-I/O-SYST EM) /Ger äte besc hrei bu ng/Ei nlei tu ng/L ED-A nzeig e/Ver weis au f Kapit el "Anz eige elemen te" @ 5\mod_1246010525000_21.docx @ 36194 @ @ 1

The meaning of the LEDs is described in the “Display Elements” section.

Pos: 18.1 0 / Ser ie 7 50 ( WAG O-I/ O-SYST EM) /Ger äte besc hrei bu ng/Ei nlei tung /V ersorgung/Versorgung 24 V über CAGE CLAMP-Ans chlüss e oder Elektr onikb aust ein @ 4\mod_1236062578765_21.docx @ 27950 @ @ 1

The 24 V power supply can be fed in via the 24 V and 0 V CAGE CLAMP

®

connectors, or as an alternative, via the electronic module's ribbon cable.

Pos: 18.1 1 / Ser ie 7 50 ( WAG O-I/ O-SYST EM )/ Wichti g e Erl äuter ung en /Sic her hei ts- und s ons tige Hi nwei se /Hin wei s/Hi n weis: Pot enti alei ns peis e klem me ei nset ze n! ( kein e L K) @ 3\mod_1226499089640_21.docx @ 25026 @ @ 1

Use a supply module!

Use a supply module for field-side power supply of downstream I/O modules.

Pos: 18.1 2 / Ser ie 7 50 ( WAG O-I/ O-SYST EM )/G erät ebe schr eib ung /Ei nlei tung /V ersor gu ng/G al vanis ch e Tr en nung Fel d/S yste m @ 3\mod_1233756478750_21.docx @ 27102 @ @ 1

The field voltage and the system voltage are electrically isolated from each other.

Pos: 18.1 3 / Ser ie 7 50 ( WAG O-I/ O-SYST EM)/ Gerät ebesc hreib ung/ Einlei tung/ Versor gung /An ordnung unter Ber üc ksichti gung der Leis tungs konta kte beli ebig @ 3\mod_1233756233468_21.docx @ 27099 @ @ 1

With consideration of the power jumper contacts, the individual modules can be

arranged in any combination when configuring the fieldbus node. An arrangement

in groups within the group of potentials is not necessary.

Pos: 18.1 4 / Ser ie 7 50 ( WAG O-I/ O-SYST EM) /Ger äte besc hrei bu ng/Ei nlei tung /Ein satzb ereic h/Ein satzb ereic h 750-x xxx alle K oppler /Co ntroll er ohne Einsc hränk ung @ 3\mod_1232541691906_21.docx @ 26522 @ @ 1

14 Device Description WAGO-I/O-SYSTEM 750

750-1501 16DO 24V DC 0.5A, ribbon cable, low-side switching

Manual

Version 1.1.0

The I/O module 750-1501 can be used with all fieldbus couplers/controllers of the

WAGO-I/O-SYSTEM 750.

Pos: 19 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 15

750-1501 16DO 24V DC 0.5A, ribbon cable, low-side switching

Manual

Version 1.1.0

Pos: 20 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n für al le S eri en/G erä teb esc hrei bu ng/A nsic ht - Ü b erschr if t 2 @ 4\ mod_1240984217343_21.docx @ 31958 @ 2 @ 1

3.1 View

Pos: 21 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /G erät eb esc hrei bung /Ans ic ht/D ig itala usg ang skl emm en/ Ansic ht 75 0-150x 16 DO Stecker Flachbandkabel - Ab b @ 3 \mod_1224766423562_21.docx @ 24657 @ @ 1

Figure 1: View

Pos: 22 /Serie 750 (WAGO-I/O-SYST EM )/ Ger äteb esc hrei bu ng/A nsic ht /Ansi c ht mit Fl ach ban dka bel- Anschluss - L egend e @ 20\mod_1412696658916_21.docx @ 165335 @ @ 1

Table 3: Legend for Figure “View”

Pos.

Description

Details See Section

1

Marking possibility with

Mini-WSB

---

2

Status LEDs

“Device Description” > “Display Elements”

3

Data contacts

“Device Description” > “Connectors”

4

Connector

“Device Description” > “Connectors”

5 Release tab

“Mounting” > “Inserting and Removing

Devices”

6

CAGE CLAMP

®

connectors

“Device Description” > “Connectors”

Pos: 23 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

16 Device Description WAGO-I/O-SYSTEM 750

750-1501 16DO 24V DC 0.5A, ribbon cable, low-side switching

Manual

Version 1.1.0

Pos: 24 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n für al le S eri en/G erä teb esc hrei bung /Ans chl üsse - Üb ersc hrift 2 @ 4\ mod_1240984262656_21.docx @ 31961 @ 2 @ 1

3.2 Connectors

Pos: 25 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bu ng/A nsc hlüss e/D ate nko ntakt e/Kl em menbu s - Ü bersc hrift 3 @ 6\mod_1256294684083_21.docx @ 43660 @ 3 @ 1

3.2.1 Data Contacts/Internal Bus

Pos: 26.1 /Serie 750 (WAGO-I/O-SYST EM) /Ger äte besc hrei bu ng/A nsc hlüss e/D ate nkon takt e - F eldbu sko ppler /-c ontr oll er, A bbi ld ung und Besc hrei bu ng @ 3\mod_1231771259187_21.docx @ 26002 @ @ 1

Communication between the fieldbus coupler/controller and the I/O modules as

well as the system supply of the I/O modules is carried out via the internal bus. It

is comprised of 6 data contacts, which are available as self-cleaning gold spring

contacts.

Figure 2: Data Contacts

Pos: 26.2 /Serie 750 (WAGO-I/O-S YSTEM )/Wi chtig e Erläut eru ngen/ Sicher heits- und sons tig e Hi nw eis e/Ac htu ng/A ch tung : Bus kl em men ni c ht a uf G oldf eder kon ta kte l eg en! @ 7\ mod_1266318463636_21.docx @ 50695 @ @ 1

Do not place the I/O modules on the gold spring contacts!

Do not place the I/O modules on the gold spring contacts in order to avoid soiling

or scratching!

Pos: 26.3 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htige Erl äuter unge n/Sic herhei ts- und sonstige Hinweise/Achtung/Achtung: ESD - Auf g ute Erd ung der U mg ebu ng ac ht en! @ 7\ mod_1266318538667_21.docx @ 50708 @ @ 1

Ensure that the environment is well grounded!

The devices are equipped with electronic components that may be destroyed by

electrostatic discharge. When handling the devices, ensure that the environment

(persons, workplace and packing) is well grounded. Avoid touching conductive

components, e.g. data contacts.

Pos: 27 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 17

750-1501 16DO 24V DC 0.5A, ribbon cable, low-side switching

Manual

Version 1.1.0

Pos: 28 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bu ng/A nsc hlüss e/Fl ach ban dkab el- u nd C AGE C LAM P-A nschl üss e - Üb ersc hrif t 3 @ 9 \mod_1281677792700_21.docx @ 63520 @ 3 @ 1

3.2.2 Ribbon Cable and CAGE CLAMP

®

Connectors

Pos: 29 /S eri e 7 50 ( WA GO-I/ O-SYST EM)/ Gerät ebesc hrei bung/A nschl üss e/Digi talausg angs kle mmen/ Anschl üsse 750- 150x 16 D O S tec ker Fl ac hb and kabel @ 3\mod_1232518856187_21.docx @ 26492 @ @ 1

A 20-pole male connector is used to connect the field devices.

Via two CAGE CLAMP

®

connectors the field supply voltage is fed in.

Figure 3: Connectors

Table 4: Legend for Figure “Connectors”

Channel

Designation

Connector

Function

1

Output

DO 1

1 Output DO 1: Signal voltage

2

Output

DO 2

2 Output DO 2: Signal voltage

.

15

Output

DO 15

15 Output DO 15: Signal voltage

16

Output

DO 16

16 Output DO 16: Signal voltage

-

+24 V

17, 19

Field supply voltage +24 V (transmission)

-

0 V

18, 20

Field supply voltage 0 V (transmission)

-

+24 V

21

Field supply voltage +24 V (feed-in)

-

0 V

22

Field supply voltage 0 V (feed-in)

Pos: 30 /D o kume ntatio n allg emein/ Glie derung sele mente /---Seite nwe chsel --- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

18 Device Description WAGO-I/O-SYSTEM 750

750-1501 16DO 24V DC 0.5A, ribbon cable, low-side switching

Manual

Version 1.1.0

Pos: 31 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n für al le S eri en/G erä teb esc hrei bu ng/A nzei geel e ment e - Ü bersc hrift 2 @ 4\ mod_1240984390875_21.docx @ 31 964 @ 2 @ 1

3.3 Display Elements

Pos: 32 /S eri e 7 50 ( WA GO-I/ O-SYSTEM)/Gerätebeschreibung/Anzeigeelemente/Digitalausgangsklemmen/Anzeigeelemente 750-15xx 16 DO @ 3\mod_1232460663781_21.docx @ 26393 @ @ 1

Figure 4: Display Elements

Table 5: Legend for Figure “Display Elements”

Channel

Designation

LED

State

Function

1 State DO1 1

Off

Output DO 1: Signal voltage (0)

Green

Output DO 1: Signal voltage (1)

2 State DO 2 2

Off

Output DO 2: Signal voltage (0)

Green

Output DO 2: Signal voltage (1)

.

15 State DO 15 15

Off

Output DO 15: Signal voltage (0)

Green

Output DO 15: Signal voltage (1)

16 State DO 16 16

Off

Output DO 16: Signal voltage (0)

Green

Output DO 16: Signal voltage (1)

Pos: 33 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n für al le S eri en/G erä teb esc hrei bu ng/B edi enel eme nte - Üb ersc hrif t 2 @ 4 \mod_1239191655456_21.docx @ 30439 @ 2 @ 1

3.4 Operating Elements

Pos: 34 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bu ng/B edie nel emen te/ Bedi enel eme nte Bus kle mm e 75 0-xx xx nicht vor han den @ 4\mod_1236322031125_21.docx @ 28063 @ @ 1

The I/O module 750-1501 has no operating elements.

Pos: 35 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 19

750-1501 16DO 24V DC 0.5A, ribbon cable, low-side switching

Manual

Version 1.1.0

Pos: 36 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n für al le S eri en/G erä teb esc hrei bu ng/Sc he mati sch es S ch altbi ld - Über schr ift 2 @ 4\mod_1240984441312_21.docx @ 31967 @ 2 @ 1

3.5 Schematic Diagram

Pos: 37 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /G erät eb esc hrei bung /Sc he mati sche Sc hal tbil der/D ig ital aus ga ngs klem me n/Sc he matis ches Sc hal tbil d 75 0-1 5xx 16 D O LS S Stec ker @ 3\ mod_1233846401846_21.docx @ 27352 @ @ 1

Figure 5: Schematic Diagram

Pos: 38 /Doku ment ation all gemei n/Gli eder ungselemente/---Seite nwe chs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

20 Device Description WAGO-I/O-SYSTEM 750

750-1501 16DO 24V DC 0.5A, ribbon cable, low-side switching

Manual

Version 1.1.0

Pos: 39 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n für al le S eri en/G erä teb esc hrei bu ng/Te ch nisc he D ate n - Ü ber schr ift 2 @ 3\ mod_1232967587687_21.docx @ 26924 @ 2 @ 1

3.6 Technical Data

Pos: 40.1 /Serie 750 (WAGO-I/O-SYST EM )/ Ger äteb esc hrei bung /T echni sc he D ate n/VS (V ari able nst euer ung )/T ech nisc he D ate n G erät (VS ) ( nur Ger äte date n, kei ne T emp era turang aben) @ 20\mod_1413881815093_21.docx @ 166173 @ 3 @ 1

3.6.1 Device

Table 6: Technical Data – Device

Width

12 mm

Height (from upper edge of 35 DIN rail)

73 mm

Depth

100 mm

Weight

50 g

Pos: 40.2 /Serie 750 (WAGO-I/O-SYST EM )/ Ger äteb esc hrei bung /T echni sc he D ate n/VS (V ari able nst euer ung )/T ech nisc he D ate n K omm uni kati on ( VS) @ 4\mo d_1242119312796_21.docx @ 32970 @ 3 @ 1

3.6.2 Communication

Table 7: Technical Data – Communication

Bit width

16 bits

Pos: 40.3 /Serie 750 (WAGO-I/O-SYST EM )/ Ger äteb esc hrei bung /T echni sc he D ate n/VS (V ari able nst euer ung )/T ech nisc he D ate n V ers orgu ng (VS) @ 4\mod_1237879183953_21.docx @ 28889 @ 3 @ 1

3.6.3 Supply

Table 8: Technical Data – Supply

Voltage supply

Via system supply (internal bus) and

CAGE CLAMP® connectors

Supply voltage (Uv) field supply

24 VDC (-25 % … +30 %)

Current consumption field supply

approx. 11 mA

Current consumption system supply

approx. 40 mA

Isolation system/supply

500 V

Pos: 40.4 /Serie 750 (WAGO-I/O-SYST EM )/ Ger äteb esc hrei bung /T echni sc he D ate n/VS (V ari able nst euer ung )/T ech nisc he D ate n Di git ala usg äng e L SS ( VS) @ 4\mod_1237890510093_21.docx @ 28920 @ 3 @ 1

3.6.4 Outputs

Table 9: Technical Data – Inputs

No. of outputs

16

Output type

Low-side switching

Type of load

Lamps, resistive and inductive load

Switching frequency

max.

1 kHz

Output current