RADWAG HY10.120.HRP User manual

Brand: RADWAG

Model: HY10.120.HRP

Type: User manual

Quick Start

•PUE HY10

Indicator

ITKB-13-01-12-20-EN

To view the full user manual, go to the website or scan the QR code:

radwag.com/en/manuals/K5M

1. CONTENT

Indicator

×1

2. NOTES AND WARNINGS

Operate the indicator in a room where the temperature ranges between

-10–40 °C (14–104 °F) and where the relative humidity is below 80%. Potential

temperature change shall occur gradually and slowly.

-10

+14

+104

+40

Place the scale away from heat

sources. Avoid exposing the scale to

the sunlight.

Avoid exposing the scale to the inﬂu-

ence of a magnetic ﬁeld. Do not weigh

magnetic substances.

Not intended for use within EX zones.

Not intended for weighing explosive or

ﬂammable substances.

The indicator is ready for operation!

Press ON/OFF key to start the indicator.

3.2. Indicator Start-Up

3. PREPARING FOR WORK

3.1. Indicator Temperature Stabilization

Place the indicator on the workstation and leave it until it

reaches ambient temperature.

Prior to switching the device on let it

reach room temperature (estimated

stabilization time: 8 hours).

Connect the indicator to

the mains.

1 2

8 h

Programmable

workspace

Programmable

workspace

Tare:

Bruto:

0kg

2020.07.08

13:57:34

Polyfort FPP 30

Box AL

2486

st234

0.000

min max

-0- -0-

1 9

1865g

981.894736842105

1898.300

1518.640

1138.980

759.320

379.660

0.000

11 1

John Smith

Product:

Packaging:

Lot number:

Batch number:

Measurements

Average

Product:

Packaging:

Lot number:

Batch number:

Weighing

Tare:

Bruto:

0kg

John Smith 2020.07.08

13:57:34

Product:

Packaging:

Lot number:

Batch number:

Polyfort FPP 30

Box AL

2486

st234

0.000

min max

-0- -0-

1 9

1865g

981.894736842105

1898.300

1518.640

1138.980

759.320

379.660

0.000

11 1

Measurements

Average

Min

Max

Product:

Packaging:

Lot number:

Batch number:

Weighing

4. PANEL AND SCREEN

4.1. Keypad

4.2. Home Screen

Home

screen

Numeric

keypad

Operators

Back / Delete

Zeroing Taring

Operation conﬁrmation

or report printout

Quick access

keys

Quick access

keys

Programmable

workspace

Programmable

workspace

Weighing result

window

Status bar

Bar graph

Workspace

Weighing graph

Press key to enter the home screen.

Tare:

Gross:

0kg

2020.07.08

13:57:34

Polyfort FPP 30

Box AL

2486

st234

0.000

min max

-0- -0-

1 9

1865g

981.894736842105

1898.300

1518.640

1138.980

759.320

379.660

0.000

11 1

John Smith

Product:

Packaging:

Lot number:

Batch number:

Measurements

Average

Min

Max

Product:

Packaging:

Lot number:

Batch number:

Weighing

Tare:

Gross:

0kg

2020.07.08

13:57:34

Polyfort FPP 30

Box AL

2486

st234

0.000

min max

-0- -0-

1 9

1865g

981.894736842105

1898.300

1518.640

1138.980

759.320

379.660

0.000

11 1

John Smith

Product:

Packaging:

Lot number:

Batch number:

Measurements

Average

Min

Max

Product:

Packaging:

Lot number:

Batch number:

Weighing

Units

Start unit

Custom unit 2

Accessibility

Custom unit 1

Gravitational acceleration 9.80665

[g]

[ct]

[g]

[ct]

[g]

[ct]

[g]

[ct]

[g]

[ct]

Parameters

Weighing Databases Reports Working modes Communication Peripherals

Display

In / Out

Units Others User adjustment

Info

Update Remote desktopt

Access

[g]

[ct]

[lb]

Parameters

Weighing Databases Reports Working modes Communication Peripherals

Display

In / Out

Units Others User adjustment

Info

Update Remote desktopt

Access

[g]

[ct]

[lb]

Working Modes

Parts counting

Dosing

PGC

Animal weighing

Transactions

Weighing

Percent weighingi

Formulations

Density

Vehicle scale

SQC

Start unit

Start unit -

Platform 2

Start unit-

Platform 1

[g]

[ct]

[g]

[ct]

None None

5.1. Working Modes

5.2. Unit Selection

Press the current working mode pictogram to

display the list of all working modes.

Select working mode from the list.

Select units in the menu.

Select “Start unit” parameter in the menu. Next, select the platform to which the start

unit is to be assigned.

5. SETTINGS

Start unit

Jednostka startowa -

Platforma 2

Jednostka startowa -

Platforma 1

[g]

[ct]

[g]

[ct]

Brak Brak

Start unit

None g kg lb

Select start unit.

6. CONNECTING PERIPHERALS

100-240V AC

50-60Hz

USB (2)USB (1) RS 232 (1) ETHERNET 4IN4OUT

PLATFORM 1

RS232 (2) RS232 (3) Vk 1 Vk 2 Vk 3 PLATFORM 2ON/OFF

15 16

5 6

Power supply switch.

2 RS232 (2) connector.

3 RS232(3) M12 8P connector - optional.

Spot intended for cable gland / additional equipment connector (Vk1, RS485,

Analog OUT) – mounted depending on indicator type, by default plugged.

Spot intended for cable gland / additional equipment connector (Vk1, 12OUT,

PROFIBUS OUT) – mounted depending on indicator type, by default plugged.

Spot intended for cable gland / additional equipment connector (Vk1, 12IN,

PROFIBUS IN) – mounted depending on indicator type, by default plugged.

7 Platform 2 cable gland.

7. CLEANING AND MAINTENANCE

7.1. Notes and Warnings

8 Grounding terminal.

9 Power cord cable gland.

10 USB A connector.

11 USB M12 4P connector.

12 RS232(1) M12 8P connector.

13 Ethernet RJ45 connector.

14 4OUT M12 8P connector.

15 4IN M12 8P connector.

16 Platform 1 cable gland.

Prior to cleaning it is necessary

to disconnect the indicator from

the mains. Unplug the connector

from the electrical socket. Unused

communication interfaces must be

covered with hole plugs.

For cleaning use only soft cloths made

of microﬁber. Do not use any abrasive

cloths or any material that may scratch

the surface!

Apply the cleanser onto the cloth ﬁrst.

Avoid applying the cleanser directly

onto the device!

Avoid using aggressive cleaning

agents (e.g. solvents, cleansers

containing chlorine, corrosive

substances and bleach).

Avoid using cleansers containing

abrasive substances or scouring

preparations.

Avoid using intense water jet for

cleaning.

7.2. Cleaning Tips

• STAINLESS STEEL ELEMENTS, ALUMINUM can be cleaned with a soft cloth slightly moistened with a solution of water

and a mild detergent (e.g. soap or dishwashing liquid).

• Plastic elements can be cleaned with a soft cloth slightly moistened with a solution of water and a mild detergent

(e.g. soap or dishwashing liquid).

• Dry cleaned elements using soft and dry cloth or use dust-free paper towel to absorb the remaining moisture.

• Do not install the components until they are completely dry.

www.radwag.com

RADWAG HY10.120.HRP User manual

RADWAG HY10.120.HRP User manual

RADWAG HY10.120.HRP User manual

Related papers

Other documents