2. RADWAG
  3. TMX19C.6.H2.K
TMX19C.6.H2.K

RADWAG TMX19C.6.H2.K, PUE 5.19R, TMX15C.15.H2.K, TMX15IR.300.H6.K, TMX15R.15.H3.K, TMX19C.300.C3.K, TMX19IR.15.H3.K, TMX19IR.300.C2.K, TMX19IR.300.C3.K, TMX19IR.60.C2.K, TMX19R.15.F1.K User manual

  • Hello! I am an AI chatbot trained to assist you with the RADWAG TMX19C.6.H2.K User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Quick Start
•PUE 5
Indicator
ITKB-14-01-12-20-EN
To view the full user manual, go to the website or scan the QR code:
radwag.com/en/manuals/W4C
1. CONTENT
Indicator
×1
Indicator
×1
2. NOTES AND WARNINGS
Operate the indicator in a room free from dust where the temperature ranges
0–40 °C (32–104 °F) and where the relative humidity is below 80%. Potential
temperature change shall occur gradually and slowly.
Place the scale on a table or a wall bracket ensuring stability. For the most stable
and repeatable results it is recommended to use an anti-vibration table.
+0
o
C
+32
o
F
+104
o
F
+40
o
C
Place the scale away from heat
sources. Avoid exposing the scale to
the sunlight.
Avoid exposing the scale to the influ-
ence of a magnetic field. Do not weigh
magnetic substances.
Not intended for use within EX zones.
Not intended for weighing explosive or
flammable substances.
PUE 5.15
PUE 5.19
The indicator is ready for operation.
Press ON / OFF key to start the indicator.
3.2. Indicator Start-Up
3. PREPARING FOR WORK
3.1. Indicator Temperature Stabilization
Place the indicator on the workstation and leave it until it
reaches ambient temperature.
Prior to switching the device on let it
reach room temperature (estimated
stabilization time: 8 hours).
Connect the indicator to
the mains.
1 2
1
1- 8 h
Application
settings
192.192.0.00
TERMINAL
E2R
10:10
01.01.2020
POL
Mass Display
Proxy
Manager
MwManager
MWMH -
manager
MwManager State: Connected to MW-04
Connection method settings
RS 232 port settings
Connection method:
Device selection
MW01 MW-04
Application
settings
Parameters
User parameters
Communication
I/O functions
LH
1
1
2
3 4
RS 232
Port
Exit Disconnect
Com 57600 None 8 1
Baud rate Parity Data bits Stop bits
The PUE5 indicator operates in Windows environment. RADWAG applications are installed individually on customer’s
order. One of the basic applications is MwManager.
MwManager home screen.
4. HOME SCREEN
Application
settings
Parameters
Weighing result window Tare/Zero
Weighing platform
selection
Device
selection
Connection
method settings
Connection
settings
4.1. Home Screen
5. CONNECTING PERIPHERALS
ON OFF
InputsInputs
USB RS 232 USB Load CellLoad Cell
Load CellLoad Cell
Inputs
100-240V
AC
50/60Hz 0,2A
RS 232
RS 485
USB Ethernet USB
1 ON/OFF switch
2 Power cord cable gland
3 4IN connector (option)
4 RS232, RS485 or 2XPROFIBUS (IN, OUT) connector
5 USB M12 4 pin connector
6 RJ45 Ethernet connector
7 USB panel connector
8 USB panel connector
9
RS485 cable gland (option)
10 4OUT connector (option)
11 RS232 connector
12 USB M12 4 pin connector
13 Load cell cable glands (4pcs)
1
8
2
9
3
10
4
11
5
12
6 7
13
6. CLEANING AND MAINTENANCE
6.2. Cleaning Tips
6.1. Notes and Warnings
Avoid using aggressive cleaning
agents (e.g. solvents, cleansers
containing chlorine, corrosive
substances or bleach).
• Glasselementscanbecleanedwithglasscleaner.
•STAINLESSSTEELELEMENTS,ALUMINUMcanbecleanedwithasoftclothslightlymoistenedwithasolutionofwater
and a mild detergent (e.g. soap or dishwashing liquid).
•Plasticelementscanbecleanedwithasoftclothslightlymoistenedwithasolutionofwaterandamilddetergent
(e.g. soap or dishwashing liquid).
•Drycleanedelementsusingsoftanddryclothorusedust-freepapertoweltoabsorbtheremainingmoisture.
•Donotinstallthecomponentsuntiltheyarecompletelydry.
Avoid using cleansers containing
abrasive substances or scouring
preparations.
Avoid using intense water jet for
cleaning.
Prior to cleaning it is necessary
to disconnect the indicator from
the mains. Unplug the connector
from the electrical socket. Unused
communication interfaces must be
covered with hole plugs.
For cleaning use only soft cloths made
of microfiber. Do not use any abrasive
cloths or any material that may scratch
the surface!
Apply the cleanser onto the cloth first.
www.radwag.com
/