FSR FL-500P-5-B Installation guide

Brand: FSR

Model: FL-500P-5-B

Type: Installation guide

FSR 244 Bergen Boulevard, Woodland Park, NJ 07424, Phone: 973.785.4347 - Fax: 973.785.4207

43200 LIT1332B

BOX INSTALLATION - STEP 1

LOCATE AND POSITION BOX IN ACCORDANCE WITH FLOOR

PLANS. TOP SURFACE OF TEMPORARY COVER MUST BE SET

TO MATCH THE HEIGHT OF THE FINISHED FLOOR - ie STONE,

WOOD OR CONCRETE - SEE TYPICAL INSTALLATION HEIGHTS.

LEVEL AND ANCHOR BOX AS REQUIRED. USE SCREWS, NAILS,

OR WIRE TO PREVENT BOX FROM FLOATING DURING POUR.

REMOVE AND RETAIN TEMPORARY COVER AND SCREWS.

ROUTE CONDUITS TO BOX AS REQUIRED. GANG BRACKET

SCREWS MUST BE IN PLACE AND BOTTOMED TO ENSURE

SCREW VOIDS AFTER POUR. PLACE THIS INSTALLATION GUIDE

BACK INTO BOX, ALONG WITH ALL SUPPLIED ITEMS, AND

REINSTALL TEMPORARY COVER.

BOX INSTALLATION - STEP 2

SCREED TO TOP OF BOX SURFACE FOR 3/16" THICK

CARPET/FLOORING OR SPECIFIC HEIGHT TO ALLOW

FOR THICKER FINISHED FLOOR MATERIAL. HAND

TROWELING RECOMMENDED NEAR BOX EDGES.

BOX HAS NO HEIGHT ADJUSTMENT AFTER

CONCRETE POUR.

TEMPORARY

COVER

(8) #6-32 FLAT HEAD SCREW

CONCRETE SURFACE OR TOP

OF FINISHED FLOOR MATERIAL

Carpeted or Tile Floors, Cover types - BLP, BSQ, B, SLP, SSQ, S

TYPICAL INSTALLATION HEIGHTS

(4) LEVELING BOLT

FL-500P INSTALLATION INSTRUCTIONS

INSTALLING ELECTRONIC COMPONENTS

PULL WIRES AND CABLES TO BOX AS NECCESSARY (REMOVAL OF

GANG MOUNTING BRACKETS MAY BE REQUIRED). TERMINATE

WIRES AND CABLES TO ELECTRONIC COMPONENTS, AND INSTALL

ELECTRONIC COMPONENTS ONTO GANG MOUNTING BRACKETS.

REINSTALL TEMPORARY COVER IF FINISHED COVER IS TO BE

INSTALLED AT A LATER DATE.

INSTALLED

ELECTRONIC

COMPONENT

GANG

MOUNTING

BRACKET

(2) #8-32 x .25 LG

FLAT HEAD

SCREW

DIVIDER ASSEMBLY

GANG

MOUNTING

PLATE

(2) #8-32 x .375 LG

SELF TAPPING

PAN HEAD

SCREW

GANG PLATE ASSEMBLY

GANG DIVIDER ASSEMBLY

4" BOX DIVIDER 5"-6" BOX DIVIDER 7"-12" BOX DIVIDER

(2) #8-32 x .25 LG

PAN HEAD

SCREW

DIVIDER HOLDER

DIVIDER

(2) #8-32 x .25 LG

PAN HEAD

SCREW

DIVIDER HOLDER

DIVIDER

DIVIDER HOLDER

(2) #8-32 x .25 LG

PAN HEAD

SCREW

DIVIDER

Vinyl or Stained Concrete, Cover types - BK, SS, BRS

DIVIDER HOLDER MUST BE ORIENTED AS SHOWN WHEN ATTACHING

TO DIVIDERS, IN ORDER TO PROPERLY ASSEMBLE BOX INTERIOR.

* DIVIDER ASSEMBLY FOR 5" & 7" BOXES

POSITION DIVIDER ASSEMBLY IN BOX BEFORE INSTALLING

GANG PLATE ASSEMBLY. SECURE DIVIDER ASSEMBLY TO

GANG PLATE ASSEMBLY WITH SCREWS AS NOTED.

(FOR USE WITH FL-500P SERIES COVERS ONLY)

CONCRETE

TEMPORARY

COVER

FLOOR BOX

SCREED FLUSH

COVER FLUSH WITH CONCRETE

(FOR 1/8" THICK COVER) CARPET FLOORING

CONCRETE

CARPET 1/8" THICK

COVER WITH

EDGING

FLOOR BOX

TILE OR LAMINATE FLOORING

CONCRETE

FINISHED

FLOOR 1/8" THICK

COVER WITH

EDGING

FLOOR BOX

VINYL FLOORING STAINED FLOORING

CONCRETE

SCREED FLUSH

FLOOR BOX

TEMPORARY

COVER

COVER FLUSH WITH CONCRETE

(FOR 1/8" THICK COVER)

CONCRETE

FINISHED

FLOOR

FLOOR BOX

1/8" THICK COVER

SHIM TO VINYL

THICKNESS

CONCRETE

1/8" THICK COVER

FLOOR BOX

FLOOR BOX TEMPORARY COVER WILL EITHER BE INSTALLED DIRECTLY ON THE BOX OR SHIMMED

BASED ON THE COVER AND FLOORING SPECIFICATIONS. SHIM KITS SOLD SEPARATELY (FL-500P-CSK).

THE TEMPORARY COVER MAY NOT BE FLUSH WITH THE FINISH FLOOR IN ALL INSTALLATIONS.

1-GANG/2-GANG CONFIGURATION 1-GANG/3-GANG CONFIGURATION

2-GANG/2-GANG CONFIGURATION 3-GANG/1-GANG CONFIGURATION

4-GANG CONFIGURATION

GANG MOUNTING BRACKET CONFIGURATION

PER CUSTOMER SPECIFICATIONS, CONFIGURE GANG MOUNTING BRACKETS AS SHOWN BELOW AND

REASSEMBLE INTO BOX (DECORA WALL PLATES SHOWN AS REFERENCE AND NOT INCLUDED).

COVER PLATE

GANG

MOUNTING

BRACKET

OPTIONAL DIVIDER

GANG

MOUNTING

BRACKET

OPTIONAL DIVIDER

GANG MOUNTING BRACKET

OPTIONAL

DIVIDER

GANG MOUNTING BRACKET

OPTIONAL DIVIDER

DIVIDER

HOLDER

DIVIDER

HOLDER

DIVIDER

HOLDER

(2) DIVIDER

HOLDER

GANG MOUNTING BRACKET

(2) DIVIDER HOLDER

(NO DIVIDERS USED)

REMOVABLE LARGE CENTER DIVIDER

REMOVABLE SMALL

CENTER DIVIDER

REMOVABLE SMALL

CENTER DIVIDER

REMOVABLE LARGE CENTER DIVIDER

CENTER DIVIDER CONFIGURATION (NOT APPLICABLE ON 4" BOX)

SET ASIDE TEMPORARY COVER AND SCREWS FOR POSSIBLE RE-INSTALLATION.

REMOVE AND RETAIN GANG MOUNTING BRACKETS AND SCREWS TO CONFIGURE

CENTER DIVIDERS.

Vinyl or Stained Concrete, Cover types - SLD-ALM, SLD-Color

Wood / Floating Wood, Cover types - BK, SS, BRS (1/8"), SLD-ALM, SLD-Color (3/8")

Wood / Floating Wood, Cover types - BLP, BSQ, B, SLP, SSQ, S

POSSIBLE GANG DIVIDER LOCATION BOTH GANG MOUNTING BRACKETS ARE IDENTICAL, AS IS THEIR CONFIGURATION CAPABILITY

COVER FLUSH WITH CONCRETE

(FOR 3/8" THICK COVER) VINYL FLOORING STAINED FLOORING

CONCRETE

FINISHED

FLOOR 3/8" THICK COVER

SHIM TO VINYL

THICKNESS

FLOOR BOX CONCRETE FLOOR BOX

3/8" THICK COVER

CONCRETE

TEMPORARY

COVER

SHIM 1/4"

FLOOR BOX

SCREED FLUSH

CONCRETE FLOOR BOX

TEMPORARY

COVER

1/4" (SEE NOTE)

FINISHED

FLOOR

CONCRETE

FINISHED

FLOOR 1/8" THICK

COVER

FLOOR BOX

SLEEPER

SYSTEM

(IF USED) CONCRETE SLEEPER

SYSTEM

(IF USED)

FLOOR BOX

FINISHED

FLOOR 3/8" THICK

COVER

COVER ABOVE CONCRETE

(FOR COVER WITHOUT EDGING) WOOD FLOORING WOOD FLOORING

CONCRETE

EDGING

HEIGHT

FLOOR BOX

TEMPORARY COVER

FINISHED

FLOOR

FINISHED FLOOR

CONCRETE SLEEPER SYSTEM (IF USED)

1/8" THICK COVER

WITH EDGING

FLOOR BOX

COVER ABOVE CONCRETE

(FOR COVER WITH EDGING) WOOD FLOORING

FOR 3/8" THICK COVER LOWER TEMPORARY

COVER AN ADDITIONAL 1/4" FROM FINISHED

FLOOR DIMENSION OR USE SHIM KIT

NOTE:

TYPICAL INSTALLATION HEIGHTS FLOOR BOX TEMPORARY COVER WILL EITHER BE INSTALLED DIRECTLY ON THE BOX OR SHIMMED

BASED ON THE COVER AND FLOORING SPECIFICATIONS. SHIM KITS SOLD SEPARATELY (FL-500P-CSK).

THE TEMPORARY COVER MAY NOT BE FLUSH WITH THE FINISH FLOOR IN ALL INSTALLATIONS.

FSR FL-500P-5-B Installation guide

FSR FL-500P-5-B Installation guide

FSR FL-500P-5-B Installation guide

Related papers

Other documents