Overland Storage NEO XL Series Operating instructions
- Type
- Operating instructions
Overland Storage NEO XL Series
The Overland Storage NEO XL Series is a family of high-performance storage libraries that offer a range of features and capabilities to meet the demands of today's data-intensive workloads.
The NEO XL Series libraries are designed for use in a variety of applications, including:
- Data backup and recovery: The NEO XL Series libraries provide a reliable and efficient way to back up and recover data in the event of a system failure or disaster.
- Data archiving: The NEO XL Series libraries can be used to archive data that is no longer actively used, but still needs to be retained for compliance or other purposes.
Overland Storage NEO XL Series
The Overland Storage NEO XL Series is a family of high-performance storage libraries that offer a range of features and capabilities to meet the demands of today's data-intensive workloads.
The NEO XL Series libraries are designed for use in a variety of applications, including:
- Data backup and recovery: The NEO XL Series libraries provide a reliable and efficient way to back up and recover data in the event of a system failure or disaster.
- Data archiving: The NEO XL Series libraries can be used to archive data that is no longer actively used, but still needs to be retained for compliance or other purposes.
10400655-001 ©2015 Overland Storage, Inc. Page 1 of 2
*10400655001*
NEO
®
XL-Series Libraries
Add-on/Spare Power Supply Instructions
This document describes how to remove and replace a power
supply in a NEO XL-Series library or expansion module from
Overland Storage.
The NEO XL-Series library default comes with a single power
supply.
WARNING: To reduce the risk of electric shock or damage to
equipment, always remove any power cords while working with
the unit.
WARNUNG: Um das Risiko eines elektrischen Schlags oder
Schäden am Gerät zu vermeiden, ziehen Sie stets den
Netzstecker, bevor Sie an der Einheit arbeiten.
AVERTISSEMENT: Pour réduire le risque de choc électrique
ou endommagement de l'équipement, retirez toujours les
cordons électriques en travaillant avec l'appareil.
CAUTION: While working with the unit, observe standard
Electrostatic Discharge (ESD) precautions to prevent damage
to micro-circuitry or static-sensitive devices.
Install/Replace Power Supply
Locate and Disconnect the Old Power Supply
To simply add a new power supply to a library, skip to Remove
the Cover Plate for a Redundant Power Supply.
1. Locate the failed power supply on the rear of the library
using the LEDs; either the amber LED (2) will be lit or all
three LEDs will be off.
2. Unplug the AC power supply cord from the unit being
serviced.
Remove the Power Supply
1. Finger-loosen the three blue captive thumbscrews on
the power supply.
2. Using the thumbscrews, slowly pull the power supply
approximately 4 inches (10 cm) out of the library.
3. While using one hand to support the bottom of the power
supply, use the other hand to completely remove the
power supply from the module.
Proceed to Install the New Power Supply.
10400655-001 ©2015 Overland Storage, Inc. Page 2 of 2
http://support.overlandstorage.com
You can get additional technical support on the Internet at the Overland Storage Support web page, or by contacting Overland Storage using
the information found on the Contact Us page on our web site.
NEO XL-Series Library Add-on/Spare Power Supply
Remove the Cover Plate for a Redundant
Power Supply
1. Using a Phillips screwdriver, remove the three screws
securing the power supply cover plate.
2. Set the cover plate on a secure surface.
Install the New Power Supply
1. Position the new power supply onto the alignment rails.
2. Slide the power supply into the library until it is flush
with the back panel of the library.
3. Finger-tighten the blue captive thumbscrews to secure
the power supply to the library.
4. Attach the AC power cord to the new power supply.
5. Press the power button.
Verify the Power Supply Installation and
Operation
1. Verify the new power supply is operating properly by
checking:
• The white (1) and green (3) LEDs are lit.
• The amber (2) LED is off.
2. Using the OCP or RMI, confirm that the power supply is
operating correctly.
The event that indicated the power supply was faulty
should be cleared.
3. If the blue UID LED is still illuminated, deactivate it
using the
Maintenance > UID LED Control
screen in OCP or
RMI.
Return Old Parts to Overland
1. Place the old part in the anti-static bag and put it in the
replacement part’s box.
2. Use the existing packing material to secure it in the box.
3. Use an RMA to return the part to Overland Storage.
For return shipping details and RMA number, go to:
http://docs.overlandstorage.com/return-instructions.
-
1
-
2
Overland Storage NEO XL Series Operating instructions
- Type
- Operating instructions
Overland Storage NEO XL Series
The Overland Storage NEO XL Series is a family of high-performance storage libraries that offer a range of features and capabilities to meet the demands of today's data-intensive workloads.
The NEO XL Series libraries are designed for use in a variety of applications, including:
- Data backup and recovery: The NEO XL Series libraries provide a reliable and efficient way to back up and recover data in the event of a system failure or disaster.
- Data archiving: The NEO XL Series libraries can be used to archive data that is no longer actively used, but still needs to be retained for compliance or other purposes.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Overland Storage NEO Series Assembly Instructions
-
Overland Storage NEOxl 40 Assembly Instructions Manual
-
-
-
-
Overland Storage NEO 8000E User manual
-
-
-
-
