2. Carmanah
  3. MX SERIES
MX SERIES

Carmanah MX SERIES Installation guide

  • Hello! I've reviewed the Carmanah user guide for MX 300 and MX 400 cabinet door replacement. This document provides instructions on how to safely replace the doors, including disconnecting power, removing old doors, and properly installing new ones. I'm ready to answer any questions you have about the process.
  • How do I disconnect power for Solar only system?
    How do I disconnect power for MX 300 AC Cabinet Module?
    How do I disconnect power for MX 400 AC Cabinet Module?
    What size drill bit is needed to remove the old door?
    How many rivets are used to secure MX300 Cabinet Door?
    How many rivets are used to secure MX400 Cabinet Door?
MX Series
MX 300 & 400 CABINET DOOR REPLACEMENT GUIDE
LEVEL 4
1
Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 | [email protected] | carmanah.com
1. Disconnect power to system:
•Solar only: disconnect solar connector and then battery connector.
•MX 300 AC Cabinet Module: open fuse holder.
•MX 400 AC Cabinet Module: turn off breaker.
90834REVA
2
Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 | [email protected] | carmanah.com
MX 300 & 400 CABINET DOOR KIT REPLACEMENT GUIDE
LEVEL 4
1.0 MX 300 Cabinet Door Replacement
1. AC only: remove green grounding wire ring terminal at bottom of cabinet door.
2. Drill out three rivets securing door hinge to cabinet using a 0.191" drill bit, and remove door.
3. Ensure all rivets have been cleared from mounting holes and all metal debris has been removed from MX
300 cabinet.
4. Align hinge holes on replacement door with holes on cabinet and fasten with three rivets provided. Ensure
rivets protrude completely through cabinet before riveting.
5. Reconnect green grounding ring terminal if removed.
6. Reapply power to system.
Ensure door is fully closed and locked. Failure to follow these steps can result in the door not fully
closing and latching. This can result in the door staying ajar and possible damage or injury resulting
in door hinge rivets failing.
3
Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 | [email protected] | carmanah.com
MX 300 & 400 CABINET DOOR KIT REPLACEMENT GUIDE
LEVEL 4
1.1 MX 400 Cabinet Door Replacement
2. Drill out four rivets securing door hinge to cabinet using a 0.191" drill bit, and remove door.
3. Ensure all rivets have been cleared from mounting holes and all metal debris has been
removed from MX 400 cabinet.
1. Remove green grounding wire ring terminal at top of cabinet door.
4
Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 | [email protected] | carmanah.com
MX 300 & 400 CABINET DOOR KIT REPLACEMENT GUIDE
LEVEL 4
4. Remove four screws securing lock on replacement door. Remove and discard lock and screws.
5. Remove hole plug, wing nut and washer from existing door.
6. Install hole plug into replacement door. Hole plug washer and wing nut go on inside of
replacement door.
Steps 4-6 are only needed if you have optional draw latch kit.
7. Align hinge holes on replacement door with holes on cabinet and fasten with four rivets
provided. Ensure rivets protrude completely through the cabinet before riveting.
8. Reconnect green grounding wire removed in step 1.
9. Reconnect power to system.
Ensure door is fully closed and locked. Failure to follow these steps can result in the door not fully
closing and latching. This can result in the door staying ajar and possible damage or injury resulting
in door hinge rivets failing.
/