HySecurity StrongSlide M30 Installation guide

HySecurity
Brand
HySecurity
Model
StrongSlide M30
Type
Installation guide
StrongSlide™ M30
Installation Instructions
2support.hysecurity.com
Visit support.hysecurity.com for Installation manuals, replacement part instructions, part diagrams and more.
Contents
Safety Requirements ...................................................................................................................................2
Plan Site Design ..........................................................................................................................................3
Prepare Foundation .....................................................................................................................................4
Assemble Rebar .....................................................................................................................................5 - 6
Install Rebar ................................................................................................................................................7
Install Conduit in Rebar ...............................................................................................................................8
Pre-Assemble Anchors ................................................................................................................................9
Assemble Anchor Supports .......................................................................................................................10
Locate Anchors .......................................................................................................................................... 11
Finish Anchor Assemblies..........................................................................................................................12
Secure Anchors and Supports ................................................................................................................... 13
Pour Concrete ...........................................................................................................................................14
Install Arrestor Posts..................................................................................................................................15
Install Gate Supports .................................................................................................................................16
Adjust Clearances .....................................................................................................................................17
Fill Arrestor Posts ......................................................................................................................................18
Mount SlideDriver ......................................................................................................................................19
Mount Panels and Signs............................................................................................................................20
Safety Requirements
DANGER
Refer to UL 325, ASTM F2200, and SlideDriver operation manual for complete safety information. Failure to follow the
instructions and safety information may result in death or serious injury.
The StrongSlide automatic vehicular gate system is designed for UL 325 Usage Class IV installations only. A SlideDriver
installed on a StrongSlide gate is restricted to Usage Class IV only.
It is the responsibility of the system designer and/or installer ensure any safety or operational issues have been addressed.
3
MX5671 Rev. A ©2023
StrongSlide M30: Plan Site Design
Note: Determine roadway width and plan for additional clearances to install StrongSlide.
4support.hysecurity.com
StrongSlide M30: Prepare Foundation
5
MX5671 Rev. A ©2023
StrongSlide M30: Assemble Rebar
Note: Rebar and lumber not included.
6support.hysecurity.com
StrongSlide M30: Assemble Rebar
7
MX5671 Rev. A ©2023
StrongSlide M30: Install Rebar
8support.hysecurity.com
StrongSlide M30: Install Conduit in Rebar
9
MX5671 Rev. A ©2023
StrongSlide M30: Pre-Assemble Anchors
10 support.hysecurity.com
11
9
9
10
StrongSlide M30: Assemble Anchor Supports
Note: Rebar and lumber not included.
11
MX5671 Rev. A ©2023
StrongSlide M30: Locate Anchors
12 support.hysecurity.com
StrongSlide M30: Finish Anchor Assemblies
13
MX5671 Rev. A ©2023
StrongSlide M30: Secure Anchors and Supports
14 support.hysecurity.com
StrongSlide M30: Pour Concrete
15
MX5671 Rev. A ©2023
StrongSlide M30: Install Arrestor Posts
PAGE 11
16 support.hysecurity.com
StrongSlide M30: Adjust Clearances
17
MX5671 Rev. A ©2023
StrongSlide M30: Fill Arrestor Posts
18 support.hysecurity.com
StrongSlide M30: Mount SlideDriver
NOTICE
See SlideDriver installation instructions to complete SlideDriver installation.
CAUTION
SlideDriver operators are heavy.
Use proper lifting techniques when
installing the SlideDriver operator.
DANGER
Ensure all entrapment zones are protected per UL
325, ASTM F2200, and local codes and standards.
NOTICE
Disassemble the lid hinge on the electrical box for full access.
19
MX5671 Rev. A ©2023
StrongSlide M30: Mount Panels and Signs
20 support.hysecurity.com
StrongSlide M30: Install Gate Supports
GUIDE RAMP
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22

HySecurity StrongSlide M30 Installation guide

HySecurity
Brand
HySecurity
Model
StrongSlide M30
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents