Deagostini MIG 29 Operating instructions

Brand: Deagostini

Model: MIG 29

Type: Operating instructions

PACK 22

Published in the UK by De Agostini UK Ltd, Royds Withy King, 65 Carter Lane, London EC4V 5EQ.

Published in the USA by De Agostini Publishing USA, Inc., 299 Park Avenue • New York, New York 10171.

Warning: Not suitable for children under the age of 14.

is product is not a toy and is not designed or intended for use in play.

Items may vary from those shown.

STAGE PAGE

106 Pylons 255

107 The port movable stabiliser (I) 246

108 The starboard outer wing panel (II) 248

109 The port movable stabiliser (I) 250

110 The port movable stabiliser (II) 253

255

Stage 106: Pylons

Assembly

Your Parts

1. Р277 — Bottom casing of

starboard outer wing panel

2. Р278 — Fairing

3. D118 — Connector (3 pcs)

4. D121 — Connector (3 pcs.)

CM screws

MM Screws

OM screws

1 For this stage, you will need the parts provided in this

stage and in Stage 105. Install the fairing (P278) on

the bottom casing of the starboard outer wing panel

(P277), as shown.

2 Proceed by installing the connectors (D118) on the

pylons (D115) as shown. Secure them with the OM

screws.

D115

P277P278

D118

P278 D118 D121

P277

256

5 Secure the pylons from inside the casing of the

starboard outer wing panel (277) with the MM

screws, as shown.

3 Install the connectors (D121) on the pylons (D115) as

shown and secure them with the OM screws.

6 Proceed by securing the pylons with the CM screws,

as shown.

4 Proceed by installing the pylons (D115) on the outer

casing on the starboard wing panel (P277), as shown.

D115

P277

D121

D115

P277

257

Stage 107: The starboard

outer wing panel (I)

Assembly

Your Parts

1. Р279 — Bottom half of

the aileron

2. Р280 — Top half of the

aileron

3. D122 — Rod

4. D123 — Connector

NM screws

QM Screws

LP screws

1 For this stage, you will need the parts provided in

this stage and in Stage 106. Connect parts P279

and P280, as shown, and secure them with two LP

screws.

2 Install the connector (D123) into the aileron as

shown, and secure it with two LP screws.

P279 P279P280 D123

P279

D122

D123 NM QM LP

P280

258

5 Secure the bottom surface of the outer wing panel

with the NM screws in the places shown.

3 Proceed by installing the assembled aileron on the

frame of the starboard outer wing panel, as shown.

6 Proceed by installing the rod of the ailerons drive

(D122), as shown, and secure it with a QM screw.

4 Install the bottom surface of the wing with the

pylons on the frame of the starboard outer wing

panel, as shown. For easy assembly, we recommend

previously removing the ailerons drive fairing and

then putting it back in place.

P279

P277

D111 P277

D111

D122 D123

P279

259

Stage 108: The starboard

outer wing panel (II)

Assembly

Your Parts

1. Р281 — Bottom half of

the ﬂap

2. Р282 — Top half of the

ﬂap

3. D124 — Hinge

4. D125 — Hinge

LP screws

RM Screws

1 For this stage you will need the parts provided in this

stage and in Stages 107 and 98. Connect parts P281

and P282, as shown, and secure them with two LP

screws.

2 Proceed by installing the hinge (D124) on the bottom

surface of the outer wing panel, as shown, and secure

it with two LP screws.

D124

P281

P282

P281

D124

D125

LP RM

P282

260

1 Install the

assembled ﬂap,

as shown.

2 Proceed by

installing the

hinge (D125)

on the bottom

surface of the

outer wing

panel, as shown,

and secure it

with two LP

screws.

3 Connect the

electric wires as

shown.

D125

P281

D124 P281

261

D111

D012

4 Proceed by carefully

placing the wires into

the model’s fuselage.

5 Carefully mount the

outer wing panel onto

the fuselage, as shown.

6 Proceed by securing

the outer wing panel

underneath with the RM

screws, as shown.

262

Stage 109: The port

movable stabiliser (I)

Your Parts

1. D126 — Top of the stabiliser.

2. Р283 — Bushing

BM screws

P283

D126

263

1 For this stage you

will need the parts

provided in this

stage. Carefully

install the bushing

(P283) on the axis

of the stabiliser, as

shown, and secure

it with a BM screw.

Assembly

D126

P283

264

Stage 110: The port

movable stabiliser (II)

Your Parts

1. D127 — Bottom of the stabiliser.

2. Р284 —Anchor plate

LM screws

SM Screws

P284

LM SM

D127

265

1 For this stage you

will need the parts

provided in this

stage and in Stage

109. Connect the

top of the stabiliser

(D126) with the

bottom of the

stabiliser (D127), as

shown, and secure

them with the SM

screws.

2 Insert the axis of the stabiliser into the fuselage pocket and proceed by installing the anchor plate (P284), as shown,

and secure it with the LM screws. Verify the mobility of the stabiliser.

Assembly

P284

D127

D126

Deagostini MIG 29 Operating instructions

Deagostini MIG 29 Operating instructions

Deagostini MIG 29 Operating instructions

Related papers

Other documents