Rev:
Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: 1-800-426-8562
1245-771 1 of 7 6100-0226
Part No:
GROUNDED
OUTLET
GROUNDED
OUTLET BOX
GROUNDED
FIGURE 1
Maximum Load rating including surface: 250 lbs
Electrical Rating:
120V, 60Hz, 5.2A for Echo 2 leg tables
IMPORTANT SAFETY INSTRUCTIONS
For use with ECHO Electric Height Adjustable Tables, 2 Leg
For Commercial or Household Use Only
This product conforms to UL962 and is certied to CAN/CSA C22.2 No. 68.
When using an electrical furnishing, basic precautions should always be followed, including the following:
Read all instructions before using this table.
DANGER - To reduce the risk of electric shock:
1. Always unplug this furnishing from the electrical outlet before cleaning or servicing.
WARNING: TO REDUCE THE RISK OF BURNS, FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS:
1. Unplug from outlet before putting on or taking o parts.
2. Close supervision is necessary when this furnishing is used by, or near children, invalids, or disabled persons.
3. Use this furnishing only for its intended use as described in these instructions. Do not use attachments not
recommended by the manufacturer.
4. Never operate this furnishing if it has a damaged cord or plug, if it is not working properly, if it has been dropped or
damaged, or dropped into water. Return the furnishing to a service center for examination and repair.
5. Keep the cord away from heated surfaces.
6. Do not use outdoors.
7. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
8. To disconnect, turn all controls to the o position, then remove plug from outlet.
9. WARNING: RISK OF ELECTRIC SHOCK - CONNECT THIS FURNISHING TO A PROPERLY GROUNDED
OUTLET ONLY. SEE GROUNDING INSTRUCTIONS.
10. WARNING: RISK OF ELECTRIC SHOCK, FIRE, AND INJURY. REVIEW THE ASSEMBLY INSTRUCTIONS TO
CONFIRM THAT THE APPROPRIATE CRITICAL COMPONENTS AND ACCESSORIES ARE BEING USED WITH THE
FURNISHING.
SAVE THESE INSTRUCTIONS
This product must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for
electric current to reduce the risk of electric shock. This product is equipped with a cord having an equipment-grounding
conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and
grounded in accordance with all local codes and ordinances.
DANGER - Improper connection of the equipment-grounding conductor can result in a risk of electric shock.
Check with a qualied electrician or serviceman if you are in doubt as to whether the product is properly grounded.
Do not modify the plug provided with the product - if it will not t the outlet, have a proper outlet installed by a
qualied electrician.
This product is for use on a nominal 120-volt circuit and has a grounding plug that looks like the plug illustrated in sketch A
(see Figure 1). Make sure that the product is connected to an outlet having the same conguration as the plug. No adapter
should be used with this product.
ELECTRICAL MODULE & ACCESSORIES
LOCKING
CASTER
OR
PARTS
Desk
Installation Instructions
ECHO®
Scale 1 : 1
0 11/2
1/4 1/4
Tools Required
Rev:
Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: 1-800-426-8562
1245-771 2 of 7 6100-0226
Part No:
#2
4mm Hex 9/16”
NOTE: Footrest
is optional.
S200
S-1
S-1
S294
E1
B
C
D
KHGL
BC
A
NON-LOCKING
CASTER
S202 S-1
OR
F
E2 NOTE: Power
access is optional.
D2
(S294)
M6 x 50mm Screw
(8 Qty.)
(D)
Depth
TABLE SIZE(S)
(W)
Width
29”
(28.68”)
46” (45.68”)
54” (53.68”)
58” (57.68”)
64” (63.68”)
70” (69.68”)
D
W
#10 x 1" Pan Head Screw
(S-1) (8 Qty.)
M6 X 10mm Button Head
(S200) (4 Qty.)
(S202)
M5 X 16mm Pan Head Screw
(2 Qty.)
2
3
1
Rev:
Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: 1-800-426-8562
1245-771 3 of 7 6100-0226
Part No:
NOTE: Refer to instructions
(61000228) to learn more
about tether installation.
NOTE: The hitch is only
used with casters.
OR
S294
E1
E2E1
E1 F
C
M
D
D
LOCKING
CASTER
NON-LOCKING
CASTER
TUBE DIVIDER AND TETHER HITCH BRACKET INSTALLATION
M5
TUBE DIVIDERS TETHER HITCH
9/16”
(S294)
M6 x 50mm Screw
(8 Qty.)
5
4
BOTTOM
BOTTOM
Rev:
Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: 1-800-426-8562
1245-771 4 of 7 6100-0226
Part No:
AA
S200
S200
S-1
BC
A
NOTE: Power
access is optional.
WITHOUT
POWER ACCESS
WITH POWER
ACCESS
NOTE: Clamp
worksurface to
hold in place.
D2
A1 A1
#10 x 1" Pan Head Screw
(S-1) (6 Qty.)
M6 X 10mm Button Head
(S200) (4 Qty.)
OR
Rev:
Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: 1-800-426-8562
1245-771 5 of 7 6100-0226
Part No:
6
IMPORTANT!
MAKE SURE CONTROL BOX (F)
IS FIRMLY ATTACHED TO THE
WORKSURFACE!
H
C
1
S202
S202
G
2
3H
G
S-1
K
K1
7
3
4
5
6
L
H
C
#10 x 1" Pan Head Screw
(S-1) (2 Qty.)
(S202)
M5 X 16mm Pan Head Screw
(2 Qty.)
NOTE: Refer to instructions
(61000190, 61000191 and
61000192) to learn more
about cable tray installation.
1
Synchronizes motors by returning the table to lowest position. Resetting resolves most mechanism
issues. This procedure can be done with either a standard or programmable paddle.
Default Reset must be performed prior to rst use and once per month to ensure proper function.
Default Reset should also be performed if table is not operating properly.
Rev:
Part No:
Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: 1-800-426-8562
6100-0226
6 of 7
IMPORTANT! Remove all contents from under table!
1 2
COLLISION = REMOVE OBSTRUCTION
A
K
K
K
K
DEFAULT RESET
WAKE UP
TAP TO WAKE UP PADDLE 3TABLE HEIGHT IS SHOWNPADDLE SLEEPING
PROGRAMMABLE
PADDLE
STANDARD
PADDLE
NOTE: For Programmable Paddles (K)
only. Paddle (K) enters a power save
mode after 10 seconds of inactivity.
Prior to each use, user must “TAP AND
RELEASE” paddle (K) or “TAP AND
RELEASE” the menu button (K3) to
activate paddle (K).
Power save Mode: Paddle (K)
display not visible.
Tap and release to activate
paddle (K) prior to each use.
PROGRAMMABLE
PADDLE
STANDARD
PADDLE
1
245-771
K3
30.0
30.0
30.0
30.0
NOTE: Typically the table will move up slightly
but if a lower storage stop is set, it will raise up
all the way to the lower storage stop.
NOTE: This step only applies to
programmable paddle.
CUSTOMER SERVICE PHONE: 1-800-426-8562
Hold down paddle (C) for 15 seconds and release
3
2
1
THEN UP
2
K
KK
K
1
“HOLD FOR 15 SECONDS”
K
Press and hold down paddle (C) until table moves down and continue to hold until table stops moving up
4
Lower table all the way down
Press paddle (C) down
Lower table all the
way down
3Release paddle (C)
K
3Release paddle (C)
2
MOVES
DOWN SLIGHTLY
1
2
Rev:
Part No:
Page:
E.C.O. No: 6100-0226
7 of 7
RESET
1
245-771
RESET
-
1
-
2
-
3
-
4
-
5
-
6
-
7
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Haworth 6100-0189 Operating instructions
-
Haworth 6100-0018 Operating instructions
-
Haworth 6100-0051 Operating instructions
-
Haworth 7029-9930 Operating instructions
-
Haworth 6100-0251 Operating instructions
-
Haworth 7029-9932 Operating instructions
-
Haworth 6100-0060 Operating instructions
-
Haworth 7029-9903a Operating instructions
-
Haworth 6100-0128 Operating instructions
-
Haworth 7021-6844f Operating instructions
