1
© 2018 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 | midmark.com
Move System Spring Plunger Kit Installation (002-10324-00)
003-10175-00 AA2 2/6/20
Caution
Always disconnect power to chair before removing
covers or performing any service procedures.
Style A
MA10707i
Note
For parts list, refer to the Service and Parts manual.
Note
626 Shown.
Screws
Tabs
Step 1: Remove Top Cover
A) Position chair back at approximately 60°
B) Unplug chair.
C) Remove two screws from back of Top Cover.
D) Pull cover toward head end to disengage tabs,
then lift up to remove cover.
Note
For parts list, refer to the Service and Parts Manual.
2
© 2018 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 | midmark.com
Step 2: Remove Side Cladding.
A) Locate tab inside head end of chair. Push tab toward foot
end of chair. Pull cladding away from chair.
B) Pull down on three tabs located at the bottom foot end of the
cladding and pull cladding away from chair.
C) Locate tab inside at center of chair (footrest must be extended)
push tab up and pull cladding away from chair.
D) Push up on Cladding, tip up and remove.
E) Repeat process for opposite side.
MA10558-1i
Step 2: Remove Side Cladding.
A) Locate tabs inside at center of chair (footrest must be
extended). Push down on top tab and up on bottom tab.
Pull cladding away from chair.
B) Pull up on Cladding overhang, and remove.
C) Repeat process for opposite side.
626 224/225
Head End
Tab
Tabs
Center Tab
Head End Tab
MA10644i
Cladding
Overhang
Tab
Note
Remove all accessories (ex. chair arms) before performing this procedure.
Note
225 Shown.
3
© 2018 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 | midmark.com
Move System
Handle Assembly
Step 3: Remove Fixed cover.
A) Squeeze Snap-in Post together on the bottom corners of the Fixed Cover.
B) Pull upward on Fixed Cover corners.
C) lift back of Fixed Cover up then rotate 90°.
D) Slide Fixed Cover out from between Back Actuator and chair back.
Step 4: Remove Move System Handle Assembly.
A) Remove top and side Hex Head Screws.
B) Pull upward on Move System Handle Assembly. While pushing
the Spring Perch Bracket towards the seat end of the chair.
Hex Head Screw
Spring Perch
Bracket
Fixed Cover
Snap-in
Post
Bottom View
Fixed Cover
Note
626 Shown.
4
© 2018 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 | midmark.com
Spring
Plunger
Step 5: Remove Spring Plunger.
A) Push in Spring Washer slightly and rotate 90°,
B) Remove Spring Washer and Spring from Spring Plunger.
C) Unthread Hex Head Screw from Spring Plunger and remove.
Step 6: Reassemble (Reverse Order).
A) Insert Hex Head Screw into Move System Handle Frame, and secure Spring Plunger.
B) Slide Spring & Spring Washer onto Spring Plunger, rotate Spring Washer 90° to lock into place.
C) Push Spring Perch Bracket towards the seat end of the chair. Install Move System Handle Assembly,
secure with top and side Hex Head Screws.
D) Install Fixed Cover, Side Cladding, Top Cover.
Spring
Spring
Washer
Bottom View
Hex Head Screw
Move System
Handle Fame
/
