Ransomes 4156939 is a 7” Reel Turf Groomer Kit designed for use on LF 3800, LF 4677, and LF3407 cutting units. It helps to improve the appearance and health of your lawn by removing thatch and dead grass, which allows water and nutrients to reach the soil more easily. The groomer also helps to level the ground and disperse clippings, which reduces the need for raking.
Here are some of the key features of the Ransomes 4156939:
- Pre-assembled for easy installation
- Durable construction for long-lasting use
- Adjustable height settings for different lawn conditions
- Helps to improve the appearance and health of your lawn
Ransomes 4156939 is a 7” Reel Turf Groomer Kit designed for use on LF 3800, LF 4677, and LF3407 cutting units. It helps to improve the appearance and health of your lawn by removing thatch and dead grass, which allows water and nutrients to reach the soil more easily. The groomer also helps to level the ground and disperse clippings, which reduces the need for raking.
Here are some of the key features of the Ransomes 4156939:
- Pre-assembled for easy installation
- Durable construction for long-lasting use
- Adjustable height settings for different lawn conditions
- Helps to improve the appearance and health of your lawn
Instruction Sheet
This kit is intended for use on LF 3800, LF 4677 and
LF3407 cutting units.
1. Park the tractor on a flat and level surface, fully lower
the attachments to the ground, engage the parking
brake, turn the ignition switch to the off position, and
remove the key.
a. Wait for all movement to stop before making any
adjustments or modifications.
b. Allow sufficient time for the unit to cool down.
c. Take this opportunity to thoroughly inspect the
equipment and perform other required maintenance.
Groomer Identification__________________________________________________
1. The Turf Groomer has been pre-assembled into one
assembly and three bags of parts.
2. To help in the assembly process and prevent confusion
between right hand and left hand units, completely
install each Turf Groomer before starting on the next
reel.
a. Open each carton to inspect and familiarize your-
self with the contents.
b. Keep all components in original carton until ready
for assembly.
3. Remove the reels from the tractor, following directions
given in the tractor’s manuals.
4. Determine if a right hand (Product No. 67954) or a left
hand (Product No. 67973) Groomer is to be installed
for each reel. Move one reel and corresponding
groomer assembly to workbench. [See Figure 1]
Figure 1
CAUTION
Before you install this kit, read the tractor’s manual to
become familiar with the tractor, the controls and proper
use of the equipment.
Stay alert for potential hazards and follow all safety
precautions. Read all instructions completely and make
sure you understand them before proceeding with the
assembly.
!
WARNING
Before you attempt to clean, adjust, or repair any of this
equipment, lower the attachments, disengage all drives,
shut down the engine and allow the unit to cool. Remove
the key from the ignition switch and disconnect the
negative battery terminal to prevent accidental
discharge and potential bodily injuries.
Be careful to prevent entrapment of the hands and
fingers between moving and fixed components of the
machine.
To prevent personal injury and damage to the cutting
edges, handle the reel with extreme care. Always wear
gloves when picking up or moving reels, or groomer
blade assemblies.
!
Motor
End
Motor
End
Right Hand Groomer Required (67954)
Left Hand Groomer Required (67973)
Front
Front
7” Reel Turf Groomer Kit
Product No. 67954 and 67973
Litho in U.S.A. 6-2007 Part Number 4156939
REV A
2
Reel Preparation_______________________________________________________
1. Remove existing front roller (A), roller scraper (B), front
roller adjusting brackets (C) and adjusting knobs (D).
NOTE: Lift yoke is not shown for clarity. Do not remove lift
yoke from reels.
2. If powered rear roller brush is not installed:
a. Loosen retaining clamp and remove counterbalance
(E).
b. Remove top and bottom screw (G) from bearing
housing.
c. Block reel with a piece of wood, remove retaining
hardware and coupler (F).
If powered rear roller brush is installed:
a. Remove hardware (I), belt cover (H), belt (J) and
both pulleys (K and L).
b. Remove top and bottom screws (M). Remove brush
plate/adapter assembly (N).
NOTE: A new brush plate / adapter assembly is
included with the grromer kit.
c. Block reel with a piece of wood. Remove and discard
retaining hardware and pulley adapter (P).
NOTE: Do not remove spring or reel spacer from bearing
housing. Place cover over both bearing housing openings
to prevent contamination.
3. Modify frame for mounting groomer.
a. Get template bag of parts from box.
b. Determine if frame has required additional holes (T).
If holes are present, skip to step e. If holes are not
present, assemble template (R) to reel frame using 5/
16-18 x 7/8” screw and nut (S). Align edge of
template and edge of reel frame.
NOTE: Hole location is critical to smooth operation of
groomer adjustment. Holes not located properly may
cause adjusting mechanism to bind.
c. Using holes (T) in template as a guide drill two new
25/64 in. (10 mm) holes in side of frame.
d. Repeat of other side of reel frame. Discard template
and mounting hardware
e. Enlarge existing 11/32 in. (9 mm) holes (U) in height
adjusting blocks to 25/64 in. (10 mm).
Figure 2
Figure 3
Figure 4
A
E
B
F
C
G
D
I
M
J
N
K
H
L
P
U
R
S
S
T
3
Groomer Assembly ____________________________________________________
1. Obtain groomer assembly (AN) and bag of parts.
2. Assemble one grease fitting (AR) onto each adjusting
knob (AP). Hook adjuster arms (AQ) of groomer onto
adjuster knobs. Thread adjusting knob onto reel studs.
NOTE: Use upper notch of adjuster knobs for height of cut
less than 5/8” (16 mm). Use lower notch of adjuster knobs
for height of cut above 5/8in. (16 mm)
3. Assemble groomer assembly (AN) to reel frame using
two 5/16-18 x 1-3/4” hex head screws, lockwashers,
flat washers and nuts (AS). Groomer assembly must sit
flat against reel frame adjusting block.
4. Secure groomer assembly castings to reel frame using
four 5/16-18 x 3/4” hex head screws and lockwashers
(AT) in holes drilled during preparation.
Figure 5
AP
AR
AT
AQ
AQ
AN
AS
AS
AP
AR
AT
AS
AS
4
Groomer Drive Pulley __________________________________________________
The groomer drive pully assembly has been pre-assembled
for use with a rear roller brush. If rear roller brush is not
used, remove hardware (AA) and brush plate (AB) from
adapter (AC).
1. Check to be certain seal (AD) and O-ring (AE) are
properly installed and are not damaged.
2. Insert pulley coupler (AF) into bearing housing.
3. Taking care not to damage seal, slide adapter (AC)
(With or without brush plate) into bearing housing.
Secure with two 5/16-18 x 3” socket head screws (AG).
4. Insert key into keyway (AH) on coupler (AF).
5. Slide groomer drive pulley (AI) onto coupler shaft (AF).
6. Slide inside roller brush pulley half (AJ) onto coupler
shaft.
7. Secure assembly to reel using 5/16-18 x 4-1/2” hex
head screw, lockwasher and flatwasher (AK).
NOTE: Depending on which side of reel the spring is on, it
may be required to assemble the screw without the flat
washer and lockwasher first to fully seat the coupler onto
the reel shaft, then remove the screw and install the
flatwasher and lockwasher.
8. Assemble 1/4-20 x 3/8” set screw (AL) to outside roller
brush pulley (AM). Thread outer pulley fully onto inside
pulley (AJ).
Figure 6
Groomer Belt _________________________________________________________
1. Loosen hardware (AU) and eccentric hardware (AV)
on drive end of groomer.
2. Move groomer shaft in slot so pulleys are as close
together as possible. Slide belt (AW) over pulleys.
NOTE: It may be required to remove hardware (AU and
AV) and adjusting link (AX) to move adjuster shaft enough
to install the belt. If removed, parts must be installed before
proceeding.
3. Place a deep well socket on eccentric (AV) and turn to
tighten belt (AW).
NOTE: Use a deep well socket without the ratchet. The belt
must be adjusted with hand pressure ontly.
4. Hold socket securely and torque hardware (AS) to 20 ft
lb (27 Nm).
5. Remove socket and torque retaining nut (AV) to 8-10 ft
lb (11-13 Nm).
Figure 7
Figure 8
AB
AF
AG
AD
AH
AK
AC
AI
AL
AE
AJ
AM
AC
AA
AW
AU
AX
AV
AW
AM
Groomer
Shaft Pulley
AU
AX
AV
5
Groomer Roller Adjustment _____________________________________________
Groomer roller was adjusted at the factory but may have
moved during shipment and assembly.
Adjust nuts (AY) as required on both ends of roller to center
blades between roller grooves. Lock adjustment in place
with nuts (AZ).
Figure 9
Groomer Belt Cover ____________________________________________________
1. If powered rear roller brush is not installed:
a. Obtain groomer only cover (BA) from box.
b. Secure to drive assembly using #10-24 x 3/8” screws
(BB).
If powered rear roller brush is installed:
a. Obtain groomer and roller brush cover (BC) from
box.
b. Secure to drive assembly using #10-24 x 3/8” screws
(BB).
Figure 10
Rear Roller Brush______________________________________________________
1. Assemble new cover bracket (BD) to brush plate using
hardware (BF From original brush plate).
2. Slide small brush pulley (L) onto brush shaft. Adjust
locaction as required to align pulleys.
3. Remove outer pulley half (AM).
4. Place belt (J) around small pulley (L) and inside pulley
half (AJ). Tighten belt by threading outer pulley (AM)
onto inner pulley as far as possible by hand. Lock
adjustment in place with set screw (AL).
5. Assemble new brush belt cover (BE). Secure with
hardware (I).
Figure 11
AZ
AY
BA
BB
BC
BF
I
BD
AM
BE
J
L
6
Adjustments __________________________________________________________
1. Adjustments and maintenance should always be per-
formed by an qualified technician. If proper adjustment
cannot be made, contact an authorized Jacobsen
Dealer.
2. Do not wear jewelry or loose fitting clothing when
adjusting or repairing any equipment.
3. Inspect the equipment on a regular basis; establish a
maintenance schedule and keep detailed records.
a. Keep the mower clean and moving parts properly
adjusted and lubricated.
b. Replace worn or damaged parts before operating the
machine.
c. Keep shields in place and all hardware securely
fastened.
4. Use the illustrations in the Parts Catalog as reference
for the disassembly and reassembly of components.
General recommendations ______________________________________________
1. Initially, expect an increased amount of grass removal
when using the Turf Groomer. Also expect an
increased amount of wear on the reel and bedknife;
therefore, sharpening will be required more frequently.
With continued usage, however, the frequency of
sharpening will decline.
2. Do not use the Turf Groomer immediately following top
dressing as the blades will pick up the top dressing and
pass it through the reel. The groomer should be raised
to its highest position.
3. Use the Turf Groomer on a regular basis, however, if
you wish to skip a day, the Turf Groomer should be
raised to its highest level. The blades will rotate though
the grooves in the roller and keep the roller grooves
clean.
Height of cut _________________________________________________________
Before this attachment can be put into regular use, several
passes should be made over a test area, each pass at a
different setting to obtain the best possible results for your
turf conditioning needs.
1. Record the settings and conditions during the first test.
Examine the test area a few days after the first groom-
ing and record the results.
2. Your requirements will determine the final settings and
they will be governed by the type and condition of the
grass, temperature and season of the year, the
frequency of cut and many other variables.
3. Keep in mind that the conditions and settings will vary
from green to green and from one season to the next.
NOTE: Over grooming can cause severe damage to turf.
Reel and Groomer Height of cut __________________________________________
1. To set the cutting height for the reel, loosen the wing
nut (D) and thread screw (A) in or out to obtain the
desired height of cut (B) on gauge bar (C).
a. Use a small metal scale to measure dimension (B)
as the height of cut. Once dimension (B) is obtained,
tighten wing nut (D).
b. Loosen wingnut (H). Set the groomer height by
threading groomer height screw (G) in or out. Tighten
wing nut. Groomer height must not be less than 1/2
of reel height of cut (B).
NOTE: Do not set the blades at ground level or below.
To mow at this level may damage the machine as well as
the turf. The Turf Groomer was designed to be a
conditioner, not a vertical mower.
NOTE: Jacobsen does not recommend setting the
groomer blades at less than half of the reel cutting
height. This height will also help eliminate natural graining
and smooth out uneven grass.
2. Loosen hardware (E) on both ends of the reel just
enough to allow inside knobs (F) to raise or lower the
roller.
NOTE: Use upper notch of adjuster knobs (F) for height of
cut less than 5/8” (16 mm). Use lower notch of adjuster
knobs (F) for height of cut above 5/8in. (16 mm).
3. Place gauge bar across the front and rear rollers at one
end of the reel.
4. Slide the head of screw (A) over the bedknife and
adjust knob (F) to close the gap between the screw
head and the bedknife.
5. Repeat adjustment on opposite end of reel.
6. Recheck both ends of reel for proper adjustment and
tighten nuts (E).
7. Loosen hardware (J) just enough to allow outside
knobs (K) to raise or lower the groomer.
WARNING
Before you attempt to clean, adjust, or repair any of this
equipment, lower the attachments, disengage all drives,
shut down the engine and allow the unit to cool. Remove
the key from the ignition switch and disconnect the
negative battery terminal to prevent accidental discharge
and potential bodily injuries.
Be careful to prevent entrapment of the hands and fingers
between moving and fixed components of the machine.
To prevent personal injury and damage to the cutting
edges, handle the reel with extreme care. Always wear
gloves when picking up or moving reels, or groomer blade
assemblies.
!
7
8. Place the gauge bar across the front and rear rollers on
one end of the reel with head of screw (A) over the
bedknife.
9. Adjust knobs (K) to close gap between screw and
groomer blades. Repeat at other end of reel.
10. Tighten hardware (J).
11. Make absolutely certain that each Turf Groomer is
adjusted evenly on both ends and that all the cutting
units on the tractor are adjusted to the same height.
Figure 1
Raising Groomer ______________________________________________________
Note: The groomer is designed to be always ON whenever
the reel is turning.
1. The groomer blades should be raised to their highest
position when groomer is not in use.
2. To raise or lower the groomer, loosen hardware (L) on
both ends of the reel and pivot the groomer up or
down. Tighten hardware (L).
Figure 2
Belt _________________________________________________________________
A
E
B 0 - 1/2B
F
F
C
G
D
H
J
J
K
K
L
Pivot
8
NOTE: To prevent permanent damage to the belt, do not
overtighten, twist, fold or bend the belt.
Overtightening the belt may cause premature belt failure
and abraisive wear of the pulley and bearings. Twisting or
bending the belt will permanently damage the cord fibers of
the belt.
1. Once the belt has been adjusted as described in the
assembly process, no further adjustment is required.
2. Periodic inspections of the belt will be required to
check for wear.
3. Spare belts should be stored individually and not
compressed or bent into any form other than eliptical.
Lubrication ___________________________________________________________
Lubrication intervals are based on operating from 8 to 10
hours per day, 5 days per week under normal operating
conditions.
All maintenance intervals must be performed more
frequently when operating in extremely dusty conditions.
1. Always clean the grease fitting before and after lubri-
cating.
2. Lubricate with grease that meets or exceeds NLGI
Grade 2 specifications.
3. Apply grease with a manual grease gun and fill slowly
until pressure is felt. Do not use compressed air guns
to prevent damage to seals.
Grease each of the following points not more than once
a month.
a. Reel Height of Cut Knob (2 Fittings) (N)
b. Groomer bearing housings (2 Fittings) (P)
c. Roller bearings (2 Fittings) (R)
d. Micro Adjust Pivot (2 Fittings - See Note) (S)
4. For smooth operation of pivot points and other friction
points, apply several drops of SAE 30 wt. oil every 40
hours, or as required.
Clean and lubricate individual parts and components
as required. Apply Anti-seize compound between
groomer plates.
Figure 3
R
N
N
P
R
S
S
9
10
10
24
12
8
17
4
2
2
21
22
2
20
20
26
13
14
15
16
19
18
11
27
23
25
9
7
28
5
6
3
1
29
TURF GROOMER
Turf Groomer Assembly
Right Hand Groomer Shown (Left Opposite)
Serial No. All
11
> Change from previous revision
TURF GROOMER
Item Part No. Qty. Description Serial Numbers/Notes
1
400208 1 Screw 5/16–18 UNC x 4.50 Hex Head
2 446136 8 Lockwasher 5/16 Heavy .593
3 452006 1 Washer, Flat 5/16 .905 x .375 x .104 STL ZN&YL
4 4162619 1 Pulley, Outer
5 415511 1 Screw, Set 1/4–20 3/8 Cup
6 4156934 1 Square Key, .125 x .125 x 1.88 L
7 4162618 1 Pulley, Inner
8 4156931 1 Pulley, Rear Drive
9 434047 2 Screw, SHCS 5/16–18 UNC x 3 L Non Std
10 346882 1 Seal
11 3006899 1 Adaptor, Brush
12 3006021 1 O-Ring Seal
13 4156932 1 Coupler, Pulley
14 471219 2 Grease Fitting 1/8 PTF
15 4156919 2 Knob, Adjustment
16 443106 4 Nut, 5/16–18 Hex
17 — 1 Driven Assembly See Breakdown
18 4156936 1 V-Groove Belt
19 4164441 1 Cover, Brushless
20 403908 4 Screw #10–24 UNC x .375 Hex Head
21 400184 4 Screw, 5/16–18 UNC x .75 Hex Head
22 400194 2 Screw, 5/16–18 UNC x 1.75 Hex Head
23 446136 3 Washer, Lock 5/16 Heavy Part of Rear Roller Brush Kit
24 3006900 1 Cover, Belt Part of Rear Roller Brush Kit
25 400180 2 Screw, 5/16-1/8 x 1/2” Part of Rear Roller Brush Kit
26 4164440 1 Cover, Brush Belt Part of Rear Roller Brush Kit
27 4164001 1 Cover, Universal Part of Rear Roller Brush Kit
28 4156900 1 Bracket, Brush Belt Cover Part of Rear Roller Brush Kit
29 455056 2 Flat Washer, 5/16
12
TURF GROOMER
Turf Groomer Assembly
Right Hand Groomer Shown (Left Opposite)
Serial No. All
23
7
9
3
11
12
13
16
17
3
1
18
24
19
15
14
8
10
22
20
21
6
5
4
2
1
13
> Change from previous revision
TURF GROOMER
Item Part No. Qty. Description Serial Numbers/Notes
1
434030 2 Screw, 3/8–16 x 7/8’” Socket Head
2 443110 1 Nut, 3/8–16 Hex
3 446142 3 Lockwasher 3/8 Heavy
4 367162 1 Tightener Belt, Eccentric
5 365260 1 Link
6 — 1 Driven Assembly See Breakdown
7 — 1 Groomer See Breakdown
8 345556 1 • Key, .125 x .125 x .980
9 4156929 1 • Pulley, Front Drive
10 453011 2 • Washer, Flat 3/8 x .831 x .063
11 446142 2 • Lockwasher, 3/8 Heavy
12 4156930 2 • Screw, 3/8–24 UNF x 1.00 Hex Head
13 471214 2 • Grease Fitting 1/4–28
14 446136 8 Lockwasher 5/16 Heavy
15 400198 2 Screw, 5/16–18 UNC x 2.25 Hex Head
16 364441 2 Spacer
17 365343 2 Guide, Wheel
18 4156937 2 Stub, Shaft
19 400186 1 Screw 5/16–18 UNC x .875 Hex Head
20 4156942 1 Template, Reel Frame
21 443106 4 Nut, Hex 5/16–18 UNC
22 — 1 Drive Assembly See Breakdown
23 — 1 Roller Assembly See Breakdown
24 4157260 1 • Nut, 3/4–16 UNF
25
26
27
14
TURF GROOMER
Drive Assembly
Right Hand Groomer Shown (Left Opposite)
Serial No. All
19
11
16
2
5
20
21
13
6
3
17
20
16
7
9
17
15
1
8
22
16
16
4
12
14
16
19
10
19
2
15
> Change from previous revision
TURF GROOMER
Item Part No. Qty. Description Serial Numbers/Notes
1
346616 1 Stud
2 364061 2 Bracket
3 400184 1 Screw 5/16–18 UNC x .750 Hex Head
4 400186 1 Screw 5/16–18 UNC x .875 Hex Head
5 400188 1 Screw 5/16–18 UNC x .1.00 Hex Head
6 400196 1 Screw 5/16–18 UNC x .2.00 Hex Head
7 4162617 1 Spacer
8 4162611 1 Groomer Bracket, Adj. Right Used on 67954
8 4162610 1 Groomer Bracket, Adj. Left Used on 67973
9 4156913 1 Pin
10 4156914 1 Push Plate
11 4156915 1 Plate
12 4156916 1 Bracket, Roller Assembly Right Used on 67954
12 4156921 1 Bracket, Roller Assembly Left Used on 67973
13 4162612 1 Weldment, Plate Groomer Adj. Right Used on 67954
13 4162614 1 Weldment, Plate Groomer Adj. Left Used on 67973
14 4156918 1 Weldment, Spacer Bracket Right Used on 67954
14 4156923 1 Weldment, Spacer Bracket Left Used on 67973
15 4156919 1 Knob, Adjustment
16 444718 6 Nut, Hex Lock 5/16–18 UNC
17 446136 2 Lockwasher 5/16 Heavy .593
18 453009 5 Washer, Flat 5/16 x .688 x .08
19 455056 2 Washer, Flat 5/16
20 460026 1 Cotter Pin 1/8 x .750
21 471219 1 Grease Fitting 1/8 PTF
16
TURF GROOMER
Driven Assembly
Serial No. All
11
20
10
9
4
18
19
6
9
7
7
17
13
13
14
2
7
10
8
3
7
9
8
5
12
21
1
2
9
16
7
17
> Change from previous revision
TURF GROOMER
Item Part No. Qty. Description Serial Numbers/Notes
1
343616 1 Stud, Front Roller
2 364061 2 Bracket, Brush Adustable Front
3 400184 1 Screw 5/16–18 UNC x .750 Hex Head
4 400186 1 Screw 5/16–18 UNC x .875 Hex Head
5 400188 1 Screw 5/16–18 UNC x 1.00 Hex Head
6 400196 1 Screw 5/16–18 UNC x 2.00 Hex Head
7 444718 6 Nut Hex Lock 5/16–18 UNC
8 446136 2 Lockwasher 5/16 Heavy
9 453009 5 Washer, Flat 5/16 x .688 x .08
10 455056 2 Washer, Flat 5/16 x .375 x .104 BC
11 460026 1 Pin, Cotter 1/8 x .750
12 471219 1 Fitting, Grease 1/8 PTF
13 4162617 1 Spacer
14 4162610 1 Groomer Bracket, Adj. Left Used on 67954
14 4162611 1 Groomer Bracket, Adj. Right Used on 67973
15 4156913 1 Pin
16 4156914 1 Push Plate
17 4156915 1 Plate
18 4156921 1 Bracket, Roller Assembly, Left Used on 67954
18 4156916 1 Bracket, Roller Assembly, Right Used on 67973
19 4156922 1 Plate, Groomer
20 4156923 1 Weldment, Spacer Bracket Left Used on 67954
20 4156918 1 Weldment, Spacer Bracket, Right Used on 67973
21 4156919 1 Knob, Adjustment
18
TURF GROOMER
Blade Assembly
Serial No. All
11
12
13
5
6
7
8
9
10
1
2
3
4
10
20
21
18
19
8
9
4
3
2
1
15
16
17
14
19
> Change from previous revision
TURF GROOMER
Item Part No. Qty. Description Serial Numbers/Notes
1
471214 2 Grease Fitting 1/4–28
2 4156930 2 Screw, 3/8–24 UNF x 1.00 Hex Head
3 446142 2 Lockwasher, 3/8 Heavy
4 453011 2 Washer, Flat 3/8 x .831 x .063
5 4156929 1 Pulley, Front Drive
6 345556 1 Key, .125 x .125 x .980
7 367163 1 Spacer
8 458461 2 Snap Ring, Internal 1.375”
9 336962 1 Seal, Grease
10 365229 1 Bearing
11 2500227 1 Bearing Housing
12 4156927 1 Spacer
13 443832 1 Hex Jam Nut 3/4–16 Plated
14 365230 40 Blade
15 364040 1 Shim, Washer
16 365234 41 Spacer
17 4156924 1 Shaft
18 367029 1 Locknut (Jam), 3/4–16 UNF
19 4156928 1 Spacer
20 2500228 1 Bearing Housing
21 4156926 1 Spacer
22 422530 2 Set, Screw, 1/4–28 x 1/4
20
> Change from previous revision
TURF GROOMER
Roller Assembly
Serial No. All
12
9
3
4
1
2
5
6
7
8
10
11
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
Ransomes 4156939 is a 7” Reel Turf Groomer Kit designed for use on LF 3800, LF 4677, and LF3407 cutting units. It helps to improve the appearance and health of your lawn by removing thatch and dead grass, which allows water and nutrients to reach the soil more easily. The groomer also helps to level the ground and disperse clippings, which reduces the need for raking.
Here are some of the key features of the Ransomes 4156939:
- Pre-assembled for easy installation
- Durable construction for long-lasting use
- Adjustable height settings for different lawn conditions
- Helps to improve the appearance and health of your lawn
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Ransomes 2812002 Accessories Manual
-
Ransomes 62819 Accessories Manual
-
-
-
-
-
-
-
-
Other documents
-
Gleason Reel ACA/ACC Cord Reels Installation guide
-
Baroness LM551 Operating instructions
-
Toro Greensmaster 1018 Mower User manual
-
-
-
Toro Greenhouse Kit 4042 User manual
-
-
-
-
Toro Reelmaster 3555 Traction Unit User manual