Ransomes 4226620 Accessories Manual

Brand: Ransomes

Model: 4226620

Type: Accessories Manual

This kit is intended for use with Eclipse 322

™

riding greens

mowers.

1. Park the mower on a flat and level surface, verify the

parking brake is engaged, turn the ignition switch to

the OFF position, and remove the key.

a. Wait for all movement to stop before making any

adjustments or modifications.

b. Allow sufficient time for the unit to cool down.

c. Take this opportunity to thoroughly inspect the

equipment and perform other required maintenance.

2. If this kit is to be added to a reel without a Turf

Groomer™ installed, counterweight kit 4225601 must

be installed before proceding. The counterweight kit is

not included with this kit, and must be ordered

separately.

NOTE:

Figure show reel with Turf Groomer installed.

Installation is the same for reels without Turf Groomer.

Preparation ___________________________________________________________________

1. Remove reels from Eclipse 322 mower. Refer to the

mowers Parts & Maintenance manual.

a. Disconnect battery power connector(s).

b. Disconnect reel motor connections. Remove any

cable ties securing wire harness to reel or lift yokes.

c. Remove yoke cap and pin.

d. Lift up on lift arm, and slide reel out and away from

mower.

2. Move reel to work bench.

3. If Turf Groomer is installed, proceed with Rear Roller

Brush Assembly.

4. If Turf Groomer is to be installed at this time, install the

Turf Groomer first, then proceed with Rear Roller

Brush Assembly.

5. If Turf Groomer is not installed, install counterweight kit

4225601, using instructions included in counterweight

kit.

Rear Roller Brush Assembly _____________________________________________________

1. Remove and discard zerk bolt (A) from motor end of

reel.

2. Loosely assembly set screw (Item 1) into eccentric nut

(Item 2).

3. Slide eccentric nut (Item 2) onto shoulder zerk bolt

(Item 3).

4. Assemble shoulder zerk bolt (Item 3) through bearing

housing (Item 4) and reel frame into rear roller.

NOTE:

There are two different sizes of zerk bolts included

in kit. Use the 3/8-24 shoulder zerk bolt for standard rear

roller, or 7/16-20 shoulder zerk bolt for heavy duty rear

roller.

5. Loosely secure bearing housing (Item 4) to reel frame

using one 5/16-18 x 1” screw (Item 5), two flat washers

(Item 6), one lockwasher (Item 7), and one nut (Item8).

6. Slide rear roller brush (Item 9) into housing.

Figure 1

CAUTION

Before you install this kit, read the mower’s manuals to

become familiar with the mower, the controls, and

proper use of the equipment.

Stay alert for potential hazards and follow all safety

precautions. Read all instructions completely and make

sure you understand them before proceeding with the

assembly.

WARNING

Before you attempt to clean, adjust, or repair any of this

equipment, disengage all drives, shut down the engine

and allow the unit to cool. Remove the key from the

ignition switch to prevent accidental starting and

potential bodily injuries.

INSTRUCTION SHEET

Rear Roller Brush Kit 62818

Litho in U.S.A. 8-2011

Part No. 4226620-Rev A

7. Remove and discard zerk bolt (B) from other end of

reel.

8. Loosely assembly set screw (Item 1) into eccentric nut

(Item 2).

9. Slide eccentric nut (Item 2) onto shoulder zerk bolt

(Item 3).

10.Slide bearing housing (Item 4) onto rear roller brush

(Item 9).

11.Assemble shoulder zerk bolt (Item 3) through bearing

housing (Item 4) and reel frame into rear roller.

12.Loosely secure bearing housing (Item 4) to reel frame

using one 5/16-18 x 1-3/4” screw (Item 10), two flat

washers (Item 6), spacer (Item 11), shield bracket

(Item 12), lockwasher (Item 7), and nut (Item 8).

13.Remove hardware (C and D) from bottom hole of Turf

Groomer cover. Retain lockwasher (C). Discard screw

and flat washer (D).

14.Assemble #10-24 x 2-1/4” pan head screw (Item 13)

and lockwasher (C) to Turf Groomer cover.

15.Assemble 3/8-16 x 3/4” hex head screw (Item 14),

lockwasher (Item 15), flat washer (Item 16), and spacer

(Item 17) to motor end of brush shaft.

16.Slide spacer (Item 18) and spring (Item 19) onto long

end of brush shaft.

17.Place key (Item 20) onto brush shaft.

18.Loosely assemble two set screws (Item 23) into brush

pulley (Item 22).

19.Place belt (Item 21) over Turf Groomer pulley and

brush pulley (Item 22). Slide brush pulley onto brush

shaft.

20.Use a straight edge to align pulleys and tighten set

screws (Item 23).

21.Assemble 3/8-16 x 3/4” screw (Item 14), lockwasher

(Item 15), and flat washer (Item 24) to end of brush

shaft.

22.Remove and discard 1/4” hardware (E).

23.Loosely assemble 5/16-1-1/4” hex head screw (Item

25), front shield bracket (Item 26), lockwasher (Item 7),

and nut (Item 8).

24.Assemble belt shield (Item 27) to shield brackets using

two 1/4-20 x 3/4” hex head screws (Item 28),

lockwashers (Item 29), and flat washers (Item 30).

25.Adjust belt shield and shield brackets as required to

provide even clearance for belt. Tighten belt shield and

shield brackets hardware.

Figure 2

Figure 3

Figure 4

Figure 5

Brush Adjustment______________________________________________________________

Brush should be adjusted so the bristles just touch the

roller an equal amount along the entire length of the roller.

Adjusting the brush too tight against the roller will result is

increased motor amperage and temperature, and will

shorten operating time for battery units.

To adjust brush:

1. Loosen hardware (G) and set screw (H) on both ends

of brush.

2. Turn eccentric nut (F) as required to obtain proper

adjustment. Repeat for opposite end of brush.

3. Tighten set screw (H) and hardware (G).

Parts List _____________________________________________________________________

Support ______________________________________________________________________

If you encounter any problems while installing this kit,

contact your Jacobsen Dealer, or contact the Jacobsen

Customer Care department.

Jacobsen, A Textron Company

11108 Quality Drive

Charlotte, NC 28273

800-848-1636

http://www.Jacobsen.com

Item Part No. Qty. Description Serial Numbers/Notes

415510 2

Set Screw, 1/4-20 x 1/4”

3008039 2

Eccentric Nut

3 1002225 2 Bolt, 3/8-24 Shoulder Zerk Used with Standard Rear Roller

3 1002228 2 Bolt, 7/16-20 Shoulder Zerk Used with Heavy Duty Rear Roller

4 4223938 2 Bearing Housing

4223930 1 Bearing, Ball

338763 1 Oil Seal

471214 1 Grease Fitting, 1/4-28 Straight

5 400188 1 Screw, 5/16-18 x 1” Hex Head

6 452006 4 Flat Washer, 5/16

7 446136 3 Lockwsaher, 5/16 Heavy

8 443106 3 Nut, 5/16-18 Hex

9 4223937 1 Brush Assembly

4223935 1 • Replacement Brush

10 400194 1 Screw, 5/16-18 x 1-3/4” Hex Head

11 3005970 1 Spacer, 3/8 x 5/8 x 1/2”

12 4225621 1 Bracket, Rear Shield

13 800911 1 Screw, #10-24 x 2-1/4” Pan Head

14 400258 2 Screw, 3/8-16 x 3/4” Hex Head

15 446142 2 Lockwasher, 3/8 Heavy

16 453011 1 Flat Washer, 3/8 x 13/16”

17 365293 1 Spacer, 5/8 x 7/8 x 5/32”

18 365294 1 Spacer, 5/8 x 7/8 x 1-1/8”

19 363818 1 Spring

20 363016 1 Key, 1/8 x 1/8 x 1/2”

21 4132996 1 Belt, Rear Roller Brush

22 4182082 1 Pulley, Roller Brush

23 415522 2 Set Screw, 5/16-18 x 3/8 Knurled Cup

24 452008 1 Flat Washer, 3/8 x 1”

25 400190 1 Screw, 5/16-18 x 1-1/4” Hex Head

26 4199902 1 Bracket, Front Shield

27 5001067 1 Shield, Belt

4181863 1 Decal, Read Manual for Service

28 400108 2 Screw, 1/4-20 x 3/4” Hex Head

29 446130 2 Lockwasher, 1/4 Heavy

30 453023 2 Flat Washer, 1/4 x 5/8”

Ransomes 4226620 Accessories Manual

Ransomes 4226620 Accessories Manual

Ransomes 4226620 Accessories Manual

Related papers

Other documents