Ransomes 67988, 67989 Accessories Manual

Brand: Ransomes

Model: 67988, 67989

Category: Lawnmowers

Type: Accessories Manual

Instruction Sheet

This kit is intended for use on LF-3800

™

, LF-4677

™

, and

LF-570

™

cutting units.

1. Park the mower on a flat and level surface, fully lower

the attachments to the ground, engage the parking

brake, turn the ignition switch to the off position, and

remove the key.

a. Wait for all movement to stop before making any

adjustments or modifications.

b. Allow sufficient time for the unit to cool down.

c. Take this opportunity to thoroughly inspect the

equipment and perform other required maintenance.

Groomer Identification__________________________________________________

1. The Turf Groomer has been pre-assembled into one

assembly and three bags of parts.

2. To help in the assembly process and prevent confusion

between right hand and left hand units, completely

install each Turf Groomer before starting on the next

reel.

a. Open each carton to inspect and familiarize your-

self with the contents.

b. Keep all components in original carton until ready

for assembly.

3. Remove the reels from the mower, following directions

given in the mower’s manuals.

4. Determine if a right hand (Product No. 67989) or a left

hand (Product No. 67988) Groomer is to be installed

for each reel. Move one reel and corresponding

groomer assembly to workbench. [See Figure 1]

Figure 1

CAUTION

Before you install this kit, read the mower’s manual to

become familiar with the mower, the controls, and

proper use of the equipment.

Stay alert for potential hazards and follow all safety

precautions. Read all instructions completely and make

sure you understand them before proceeding with the

assembly.

WARNING

Before you attempt to clean, adjust, or repair any of this

equipment, lower the attachments, disengage all drives,

shut down the engine, and allow the unit to cool.

Remove the key from the ignition switch and disconnect

the negative battery terminal to prevent accidental

discharge and potential bodily injuries.

Be careful to prevent entrapment of the hands and

fingers between moving and fixed components of the

machine.

To prevent personal injury and damage to the cutting

edges, handle the reel with extreme care. Always wear

gloves when picking up or moving reels, or groomer

blade assemblies.

Motor

End

Motor

End

Right Hand Groomer Required (67989)

Left Hand Groomer Required (67988)

Front

7” Reel Turf Groomer

Kit

Product No. 67988 and 67989

Litho in U.S.A. 5-2012 Part No. 4236782-Rev B

Reel Preparation_______________________________________________________

1. Remove existing front roller (A), roller scraper (B), front

roller adjusting brackets (C), and adjusting knobs (D).

NOTE:

Lift yoke is not shown for clarity. Do not remove lift

yoke from reels.

2. If powered rear roller brush is not installed:

a. Loosen retaining clamp and remove counterbalance

(E).

b. Remove top and bottom screw (G) from bearing

housing.

c. Block reel with a piece of wood, remove retaining

hardware, and coupler (F).

If powered rear roller brush is installed:

a. Remove hardware (I), belt cover (H), belt (J), and

both pulleys (K and L).

b. Remove top and bottom screws (M). Remove and

discard brush plate/adapter assembly (N).

NOTE:

A new brush plate / adapter assembly is

included with the groomer kit.

c. Block reel with a piece of wood. Remove and discard

retaining hardware and pulley adapter (P).

NOTE:

Do not remove spring or reel spacer from bearing

housing. Place cover over both bearing housing openings

to prevent contamination.

3. Modify frame for mounting groomer.

a. Get template bag of parts from box.

b. Determine if frame has required additional holes (T).

If holes are present, skip to step e. If holes are not

present, assemble template (R) to reel frame using

one 5/16-18 x 7/8” screw and nut (S). Align edge of

template and edge of reel frame.

NOTE:

Hole location is critical to smooth operation of

groomer adjustment. Holes not located properly may

cause adjusting mechanism to bind and may affect

ability to achieve proper belt tension.

c. Using holes (T) in template as a guide drill two new

25/64 in. (10 mm) holes in side of frame.

d. Repeat of other side of reel frame. Discard template

and mounting hardware

e. Enlarge existing 11/32 in. (9 mm) holes (U) in height

adjusting blocks to 25/64 in. (10 mm).

Figure 2

Figure 3

Figure 4

Groomer Assembly ____________________________________________________

1. Obtain groomer assembly (AN) and bag of parts.

2. Assemble one grease fitting (AR) onto each adjusting

knob (AP). Hook adjuster arms (AQ) of groomer onto

adjuster knobs. Thread adjusting knob onto reel studs.

NOTE:

Use upper notch of adjuster knobs for height of cut

less than 5/8 in. (16 mm)

Use lower notch of adjuster

knobs for height of cut above 5/8 in. (16 mm).

3. Assemble groomer assembly (AN) to reel frame using

two 5/16-18 x 1-3/4” hex head screws, lockwashers, flat

washers, and nuts (AS). Groomer assembly must sit

flat against reel frame adjusting block.

4. Secure groomer assembly castings to reel frame using

four 5/16-18 x 3/4” hex head screws and lockwashers

(AT) in holes drilled during preparation.

Figure 5

Groomer Adjusting Link Removal ________________________________________

1. Remove 3/8” nut, lockwasher, and eccentric nut (AV).

2. Remove 3/8-16 x 7/8” screw and lockwasher (AU).

3. Remove groomer adjusting link (AX).

4. Remove shim (CA).

NOTE:

Adjusting link and hardware will be assembled in

same location after inner belt cover and belt is installed.

Figure 6

Groomer Drive Pulley___________________________________________________

The groomer brush plate (AB) and adapter (AC) have been

pre-assembled for use with a rear roller brush.

1. Check to be certain seal (AD) and O-ring (AE) are

properly installed and are not damaged.

2. Inspect two holes (DA) on plate (AB). If holes are

tapped for #10-24 screw, plate is ok for use. If holes are

tapped for 1/4-20 screw, plate must be replaced.

3. Insert pulley coupler (AF) into bearing housing.

4. Taking care not to damage seal, slide adapter (AC) into

bearing housing. Secure with two 5/16-18 x 3” socket

head screws (AG).

5. Remove groomer shaft pulley (BZ - Figure 9). Slide

inner belt cover (BG) over groomer shaft.

6. Insert key (CB - Figure 9) into slot in groomer shaft.

Assemble groomer shaft pulley (BZ - Figure 9) onto

groomer shaft.

7. Insert key (AH) into keyway on coupler (AF).

8. Slide groomer drive pulley (AI), with stepped face

towards reel, onto coupler shaft (AF).

9. Slide inside roller brush pulley half (AJ) onto coupler

shaft.

10. Secure assembly to reel using 5/16-18 x 5” hex head

screw, lockwasher, and flat washer (AK).

NOTE:

Depending on which side of reel the spring is on, it

may be required to assemble the screw without the flat

washer and lockwasher first to fully seat the coupler onto

the reel shaft, then remove the screw and install the flat

washer and lockwasher.

11. Assemble 1/4-20 x 3/8” set screw (AL) to outside roller

brush pulley (AM). Thread outer pulley fully onto inside

pulley (AJ).

12. If groomer is to installed with a rear roller brush, install

seal (CF) onto roller brush shaft. Assemble backing

block (CD) to seal block (CC) using two M5 x 16 mm

socket head screws (CE). Assemble seal block to

brush plate (AB) using two 1/4-20 x 3/4” screws,

lockwashers, and flat washers (CG).

Figure 7

Groomer Belt _________________________________________________________

1. Move groomer shaft in slot so pulleys are as close

together as possible. Slide belt (AW) over pulleys.

2. Loosely assembly shim (CA), adjusting link (AX), and

3/8” hardware (AU and AV).

3. Place a deep well socket on eccentric (AV) and turn to

tighten belt (AW).

NOTE:

Use a deep well socket without the ratchet. The belt

must be adjusted with hand pressure only.

4. Hold socket securely and torque hardware (AU) to 20 ft

lb (27 Nm).

5. Remove socket and torque retaining nut (AV) to 8-10 ft

lb (11-13 Nm).

Figure 8

Figure 9

Groomer Roller Adjustment _____________________________________________

Groomer roller was adjusted at the factory but may have

moved during shipment and assembly.

Adjust nuts (AY) as required on both ends of roller to center

blades between roller grooves. Lock adjustment in place

with nuts (AZ).

Figure 10

Groomer Belt Cover ____________________________________________________

1. If powered rear roller brush is not installed:

a. Obtain groomer only cover (BA) from box.

b. Secure to drive assembly using #10-24 x 3/8” screws

(BB).

If powered rear roller brush is installed:

a. Obtain groomer and roller brush cover (BC) from

box.

b. Secure to drive assembly using #10-24 x 3/8” screws

(BB).

2. Insert 3/4 in. (19 mm) plug (BH) into opening in belt

cover.

Figure 11

Rear Roller Brush______________________________________________________

1. Assemble new cover bracket (BD) to brush plate using

hardware (BF From original brush plate).

2. Slide inside belt cover (BJ) onto cover bracket studs

and roller brush shaft. Secure to brush plate (AB) using

two #10-24 x 3/8” screws and flat washers (BK).

3. Slide small brush pulley (L) onto brush shaft. Adjust

locaction as required to align pulleys.

4. Remove outer pulley half (AM).

5. Place belt (J) around small pulley (L) and inside pulley

half (AJ). Tighten belt by threading outer pulley (AM)

onto inner pulley as far as possible by hand. Lock

adjustment in place with set screw (AL).

6. Assemble new brush belt cover (BE). Secure with

hardware (I).

7. Insert 5/8 in. (16 mm) plug (BL) into opening in belt

cover.

Figure 12

Adjustments __________________________________________________________

1. Adjustments and maintenance should always be

performed by an qualified technician. If proper

adjustment cannot be made, contact an authorized

Jacobsen Dealer.

2. Do not wear jewelry or loose fitting clothing when

adjusting or repairing any equipment.

3. Inspect the equipment on a regular basis; establish a

maintenance schedule and keep detailed records.

a. Keep the mower clean and moving parts properly

adjusted and lubricated.

b. Replace worn or damaged parts before operating the

machine.

c. Keep shields in place and all hardware securely

fastened.

4. Use the illustrations in the Parts Catalog as reference

for the disassembly and reassembly of components.

General recommendations ______________________________________________

1. Initially, expect an increased amount of grass removal

when using the Turf Groomer. Also expect an increased

amount of wear on the reel and bedknife; therefore,

sharpening will be required more frequently. With

continued usage, however, the frequency of

sharpening will decline.

2. Do not use the Turf Groomer immediately following top

dressing as the blades will pick up the top dressing and

pass it through the reel. The groomer should be raised

to its highest position.

3. Use the Turf Groomer on a regular basis, however, if

you wish to skip a day, the Turf Groomer should be

raised to its highest level. The blades will rotate though

the grooves in the roller and keep the roller grooves

clean.

Height of cut _________________________________________________________

Before this attachment can be put into regular use, several

passes should be made over a test area, each pass at a

different setting to obtain the best possible results for your

turf conditioning needs.

1. Record the settings and conditions during the first test.

Examine the test area a few days after the first

grooming and record the results.

2. Your requirements will determine the final settings and

they will be governed by the type and condition of the

grass, temperature and season of the year, the

frequency of cut, and many other variables.

3. Keep in mind that the conditions and settings will vary

from area to area and from one season to the next.

NOTE:

Over grooming can cause severe damage to turf.

Reel and Groomer Height of cut __________________________________________

1. To set the cutting height for the reel, loosen the wing

nut (D), and thread screw (A) in or out to obtain the

desired height of cut (B) on gauge bar (C).

a. Use a small metal scale to measure dimension (B)

as the height of cut. Once dimension (B) is obtained,

tighten wing nut (D).

b. Loosen wingnut (H). Set the groomer height by

threading groomer height screw (G) in or out. Tighten

wing nut. Groomer height must not be less than 1/2

of reel height of cut (B).

NOTE:

Do not set the blades at ground level or below.

To mow at this level may damage the machine as well as

the turf. The Turf Groomer was designed to be a

conditioner, not a vertical mower.

NOTE:

Jacobsen does not recommend setting the

groomer blades at less than half of the reel cutting

height. This height will also help eliminate natural graining

and smooth out uneven grass.

2. Loosen hardware (E) on both ends of the reel just

enough to allow inside knobs (F) to raise or lower the

roller.

NOTE:

Use upper notch of adjuster knobs (F) for height of

cut less than 5/8 in. (16 mm)

Use lower notch of adjuster

knobs (F) for height of cut above 5/8 in. (16 mm).

3. Place gauge bar across the front and rear rollers at one

end of the reel.

4. Slide the head of screw (A) over the bedknife and

adjust knob (F) to close the gap between the screw

head and the bedknife.

5. Repeat adjustment on opposite end of reel.

6. Recheck both ends of reel for proper adjustment and

tighten nuts (E).

7. Loosen hardware (J) just enough to allow outside

knobs (K) to raise or lower the groomer.

WARNING

Before you attempt to clean, adjust, or repair any of this

equipment, lower the attachments, disengage all drives,

shut down the engine, and allow the unit to cool. Remove

the key from the ignition switch and disconnect the

negative battery terminal to prevent accidental discharge

and potential bodily injuries.

Be careful to prevent entrapment of the hands and fingers

between moving and fixed components of the machine.

To prevent personal injury and damage to the cutting

edges, handle the reel with extreme care. Always wear

gloves when picking up or moving reels or groomer blade

assemblies.

8. Place the gauge bar across the front and rear rollers on

one end of the reel with head of screw (A) over the

bedknife.

9. Adjust knobs (K) to close gap between screw and

groomer blades. Repeat at other end of reel.

10. Tighten hardware (J).

11. Make absolutely certain that each Turf Groomer is

adjusted evenly on both ends and that all the cutting

units on the mower are adjusted to the same height.

Figure 1

Raising Groomer ______________________________________________________

Note:

The groomer is designed to be always ON whenever

the reel is turning.

1. The groomer blades should be raised to their highest

position when groomer is not in use.

2. To raise or lower the groomer, loosen hardware (L) on

both ends of the reel, and pivot the groomer up or

down. Tighten hardware (L).

Figure 2

B 0 - 1/2B

Pivot

Belt _________________________________________________________________

NOTE: To prevent permanent damage to the belt, do not

overtighten, twist, fold, or bend the belt.

Overtightening the belt may cause premature belt failure

and abraisive wear of the pulley and bearings. Twisting or

bending the belt will permanently damage the cord fibers of

the belt.

1. Once the belt has been adjusted as described in the

assembly process, no further adjustment is required.

2. Periodic inspections of the belt will be required to check

for wear.

3. Spare belts should be stored individually and not

compressed or bent into any form other than eliptical.

Lubrication ___________________________________________________________

Lubrication intervals are based on operating from 8 to 10

hours per day, 5 days per week under normal operating

conditions.

All maintenance intervals must be performed more

frequently when operating in extremely dusty conditions.

1. Always clean the grease fitting before and after

lubricating.

2. Lubricate with grease that meets or exceeds NLGI

Grade 2 specifications.

3. Apply grease with a manual grease gun and fill slowly

until pressure is felt. Do not use compressed air guns

to prevent damage to seals.

Grease each of the following points not more than once

a month.

a. Reel Height of Cut Knob (2 Fittings) (N).

b. Groomer bearing housings (2 Fittings) (P).

Remove plug to access fitting on belt side of

groomer.

c. Roller bearings (2 Fittings) (R).

d. Micro Adjust Pivot (2 Fittings - See Note) (S).

4. For smooth operation of pivot points and other friction

points, apply several drops of SAE 30 wt. oil every 40

hours, or as required.

Clean and lubricate individual parts and components

as required. Apply Anti-seize compound between

groomer plates.

Figure 3

TURF GROOMER

Turf Groomer Assembly

Right Hand Groomer Shown (Left Opposite)

Serial No. All

> Change from previous revision

TURF GROOMER

Item Part No. Qty. Description Serial Numbers/Notes

400210 1 Screw, 5/16–18 x 5” Hex Head

2 446136 9 Lockwasher 5/16 Heavy

3 452006 1 Washer, Flat 5/16

4 4162619 1 Pulley, Outer

5 415511 1 Set Screw, 1/4–20 x 3/8 Cup

6 4156934 1 Square Key, 1/8 x 1/8 x 1-7/8”

7 4162618 1 Pulley, Inner

8 4226320 1 Pulley, Rear Drive

9 434047 2 Screw, 5/16–18 x 3” Hex Socket

10 346882 1 Seal

11 3006899 1 Adaptor, Brush

12 3006021 1 O-Ring Seal

13 4272394 1 Coupler, Pulley

14 471219 2 Grease Fitting 1/8 PTF

15 4156919 2 Knob, Adjustment

16 443106 4 Nut, 5/16–18 Hex

17 — 1 Driven Assembly See Breakdown

18 4227241 1 Belt, Cog

19 4175224 1 Cover, Outer Groomer Belt Only used without Rear Roller Brush

20 403908 4 Screw #10–24 x 3/8” Hex Head

21 400184 4 Screw, 5/16–18 x 3/4” Hex Head

22 400194 2 Screw, 5/16–18 x 1-3/4” Hex Head

23 4175223 1 Cover, Inner Groomer Belt

24 4267170 1 Cover, Belt Only used with Rear Roller Brush

25 400180 2 Screw, 5/16-1/8 x 1/2” Only used with Rear Roller Brush

26 4192642 1 Cover, Groomer Belt, R.H. (67989) Only used with Rear Roller Brush

26 4192643 1 Cover, Groomer Belt, L.H. (67988) Only used with Rear Roller Brush

27 4175226 1 Cover, Outer Brush Belt Only used with Rear Roller Brush

28 4235040 1 Bracket, Brush Belt Cover Only used with Rear Roller Brush

29 455056 2 Flat Washer, 5/16

30 4192640 1 Cover, Inner Brush Belt, R.H. (67989) Only used with Rear Roller Brush

30 4192641 1 Cover, Inner Brush Belt, L.H. (67988) Only used with Rear Roller Brush

31 4196282 1 Plug, 5/8” Hole Only used with Rear Roller Brush

32 4196282 1 Plug, 3/4” Hole

33 452002 2 Flat Washer, #10 Only used with Rear Roller Brush

34 3009936 1 Pin Only used with Rear Roller Brush

35 3009937 1 Clip Only used with Rear Roller Brush

36 400104 1 Screw, 1/4-20 x 1/2” Hex Head Only used with Rear Roller Brush

37 453023 1 Flat Washer, 1/4 Only used with Rear Roller Brush

38 4191960 1 Block, Power Brush Seal

39 4191980 1 Block, Backing

40 450697 2 Screw, M5-0.8 x 16 mm Socket Head

41 4226322 1 Seal, V-Ring

42 400108 2 Screw, 1/4-20 x 3/4” Hex Head

43 446130 2 Lockwasher, 1/4

44 452002 2 Flat Washer

TURF GROOMER

Turf Groomer Assembly

Right Hand Groomer Shown (Left Opposite)

Serial No. All

> Change from previous revision

TURF GROOMER

Item Part No. Qty. Description Serial Numbers/Notes

434030 2 Screw, 3/8–16 x 7/8’” Socket Head

2 443110 1 Nut, 3/8–16 Hex

3 446142 3 Lockwasher 3/8 Heavy

4 367162 1 Tightener Belt, Eccentric

5 365260 1 Link

6 — 1 Driven Assembly See Breakdown

7 — 1 Groomer See Breakdown

8 345556 1 • Key, .125 x .125 x .980

9 4226321 1 • Pulley, Front Drive

10 453011 2 • Washer, Flat 3/8 x .831 x .063

11 446142 2 • Lockwasher, 3/8 Heavy

12 4156930 2 • Screw, 3/8–24 UNF x 1.00 Hex Head

13 471214 2 • Grease Fitting 1/4–28

14 446136 8 Lockwasher 5/16 Heavy

15 400198 2 Screw, 5/16–18 UNC x 2.25 Hex Head

16 364441 2 Spacer

17 4192282 2 Guide, Wheel

18 4156937 2 Stub, Shaft

19 400186 1 Screw 5/16–18 UNC x .875 Hex Head

20 4156942 1 Template, Reel Frame

21 443106 4 Nut, Hex 5/16–18 UNC

22 — 1 Drive Assembly See Breakdown

23 — 1 Roller Assembly See Breakdown

24 4157260 1 • Nut, 3/4–16 UNF

25 64163-04 1 Shim

TURF GROOMER

Drive Assembly

Right Hand Groomer Shown (Left Opposite)

Serial No. All

> Change from previous revision

TURF GROOMER

Item Part No. Qty. Description Serial Numbers/Notes

343616 1 Stud

2 364061 2 Bracket

3 400184 1 Screw 5/16–18 UNC x .750 Hex Head

4 400186 1 Screw 5/16–18 UNC x .875 Hex Head

5 400188 1 Screw 5/16–18 UNC x .1.00 Hex Head

6 400196 1 Screw 5/16–18 UNC x .2.00 Hex Head

7 4162617 1 Spacer

8 4162611 1 Groomer Bracket, Adj. Right Used on 67989

8 4162610 1 Groomer Bracket, Adj. Left Used on 67988

9 4156913 1 Pin

10 4156914 1 Push Plate

11 4156915 1 Plate

12 4244993 1 Bracket, Roller Assembly Right Used on 67989

12 4244992 1 Bracket, Roller Assembly Left Used on 67988

13 4162612 1 Plate Groomer Adj. Right Used on 67989

13 4162614 1 Plate Groomer Adj. Left Used on 67988

14 4235760 1 Spacer Bracket Right Used on 67989

14 4235721 1 Spacer Bracket Left Used on 67988

15 4176775 2 • Screw, 5/16-18 x 1” Special

16 444718 4 Nut, Hex Lock 5/16–18 UNC

17 446136 2 Lockwasher 5/16 Heavy .593

18 453009 3 Washer, Flat 5/16 x .688 x .08

19 455056 2 Washer, Flat 5/16

20 460026 1 Cotter Pin 1/8 x .750

21 471219 1 Grease Fitting 1/8 PTF

22 4156919 1 Knob, Adjustment

TURF GROOMER

Driven Assembly

Serial No. All

> Change from previous revision

TURF GROOMER

Item Part No. Qty. Description Serial Numbers/Notes

343616 1 Stud, Front Roller

2 364061 2 Bracket, Brush Adustable Front

3 400184 1 Screw 5/16–18 UNC x .750 Hex Head

4 400186 1 Screw 5/16–18 UNC x .875 Hex Head

5 400188 1 Screw 5/16–18 UNC x 1.00 Hex Head

6 400196 1 Screw 5/16–18 UNC x 2.00 Hex Head

7 444718 4 Nut Hex Lock 5/16–18 UNC

8 446136 2 Lockwasher 5/16 Heavy

9 453009 3 Washer, Flat 5/16 x .688 x .08

10 455056 2 Washer, Flat 5/16 x .375 x .104 BC

11 460026 1 Pin, Cotter 1/8 x .750

12 471219 1 Fitting, Grease 1/8 PTF

13 4162617 1 Spacer

14 4162610 1 Groomer Bracket, Adj. Left Used on 67989

14 4162611 1 Groomer Bracket, Adj. Right Used on 67988

15 4156913 1 Pin

16 4156914 1 Push Plate

17 4156915 1 Plate

18 4244992 1 Bracket, Roller Assembly, Left Used on 67989

18 4244993 1 Bracket, Roller Assembly, Right Used on 67988

19 4239142 1 Plate, Groomer

20 4235721 1 Spacer Bracket Left Used on 67989

20 4235760 1 Spacer Bracket, Right Used on 67988

21 4176775 2 Screw, 5/16-18 x 1” Special

22 4156919 1 Knob, Adjustment

TURF GROOMER

Blade Assembly

Serial No. All

> Change from previous revision

TURF GROOMER

Item Part No. Qty. Description Serial Numbers/Notes

471214 2 Grease Fitting 1/4–28

2 4156930 2 Screw, 3/8–24 UNF x 1.00 Hex Head

3 446142 2 Lockwasher, 3/8 Heavy

4 453011 2 Washer, Flat 3/8 x .831 x .063

5 4226231 1 Pulley, Front Drive

6 345556 1 Key, .125 x .125 x .980

7 367163 1 Spacer

8 2500227 1 Bearing Housing

9 336962 1 • Seal, Grease

10 365229 1 • Bearing

11 458461 2 • Snap Ring, Internal 1-3/8”

12 4156927 1 Spacer

13 443832 1 Hex Jam Nut 3/4–16 Plated

14 365230 40 Blade

15 364040 1 Shim, Washer

16 4195520 41 Spacer

17 4156924 1 Shaft

18 367029 2 Locknut (Jam), 3/4–16 UNF

19 4156928 1 Spacer

20 2500228 1 Bearing Housing

21 336962 1 • Seal, Grease

22 365229 1 • Bearing

23 458461 2 • Snap Ring, Internal 1-3/8”

24 4156926 1 Spacer

25 422530 2 Set, Screw, 1/4–28 x 1/4

26 367161 2 Spacer

> Change from previous revision

TURF GROOMER

Roller Assembly

Serial No. All

Page is loading ...

Ransomes 67988, 67989 Accessories Manual

Brand: Ransomes

Model: 67988, 67989

Category: Lawnmowers

Type: Accessories Manual

Download PDF

report

Ransomes 67988, 67989 Accessories Manual

Ransomes 67988, 67989 Accessories Manual

Related papers

Other documents