US Robotics Wireless 54Mbps ADSL Router User manual

Wireless 54Mbps ADSL Router

User Guide

R46.1172.00

rev 3 10/05

Wireless 54Mbps ADSL Router

Installation ................................................................................ 3

Configuring the Wireless 54Mbps ADSL Router ......................... 7

Troubleshooting ...................................................................... 63

Specifications .......................................................................... 75

Regulatory ................................................................................81

Warranty.................................................................................. 85

3

C

HAPTER

1

I

NSTALLATION

USR5473 Package Contents

USR9110 Wireless 54Mbps ADSL Router One (1) Ethernet cable

12VDC Power Supply USR5422 54Mbps USB Adapter

Installation Guide One (1) phone cable Installation CD-ROM

Prepare for Installation

Note: It is important that you have your serial number written down

before you install the Wireless 54Mbps ADSL Router. You can find

your serial number on the bottom label of the Wireless 54Mbps ADSL

Router. If you ever need to call our Technical Support department, you will

need this number to receive assistance.

Note: Be sure to find out what letter your CD-ROM drives uses before

you begin installing your new product. You will need to know this to

properly install your software.

Step One: Connect Microfilter(s) (if included or required by your ISP)

A microfilter removes interference between voice and DSL signals. Your ISP

will determine if a microfilter is necessary. If a microfilter was not included

with the Wireless 54Mbps ADSL Router, ask your ISP if you need to purchase

one or more.

To install a microfilter, plug each device (phone, fax machine, or other

telephony device) into the microfilter and then plug the microfilter into the

telephone wall jack. Do not install a microfilter on the cable that will con-

nect your Wireless 54Mbps ADSL Router to the telephone jack unless your

Model Number Serial Number

USR9110

I

NSTALLATION

4

microfilter has a connection for both the router and the phone.

Step Two: Connect your Wireless 54Mbps ADSL Router to the wall phone

jack

• Turn off your computer.

• Connect one end of the included phone cable to the ADSL port on the

Wireless 54Mbps ADSL Router. Connect the other end of the phone cable

to a wall phone jack.

Step Three: Connect your Wireless 54Mbps ADSL Router to your computer

and connect the power supply

Connect one end of the supplied Ethernet cable to your computer’s Ether-

net adapter. Connect the other end to the LAN port on the Wireless 54Mbps

5

ADSL Router.

Connect the included power adapter to the power socket on the Wireless

54Mbps ADSL Router. Plug the power adapter into a standard power outlet.

Turn on your computer.

’

Proceed to Chapter 2 to configure the Wireless 54Mbps ADSL Router.

I

NSTALLATION

6

7

C

HAPTER

2

C

ONFIGURING

THE

W

IRELESS

54M

BPS

ADSL R

OUTER

To access the Wireless 54Mbps ADSL

Router’s Web User Interface, launch a Web

browser and type the default IP address of

the Wireless 54Mbps ADSL Router in

address line: http://192.168.2.1.

By default, there is no password, so click LOGIN to access the Web

User Interface.

If you are logging in to the Web User Interface for the first time, the

country selection page will appear. Please select the country in which

you will be using the Wireless 54Mbps ADSL Router and then click

Apply. Then confirm your country selection by clicking OK.

C

ONFIGURING

THE

W

IRELESS

54M

BPS

ADSL R

OUTER

8

Navigating the Web User Interface

This is the advanced setup page:

Setup Wizard: Use the Setup Wizard if you want to quickly set up the

Wireless 54Mbps ADSL Router. Go to “Setup Wizard” on page 9.

Advanced Setup: Advanced Setup supports more advanced functions

like hacker attack detection, IP and MAC address filtering, virtual

server setup, QoS, as well as other functions. Go to “Advanced

Setup” on page 20.

Making Configuration Changes

Configurable parameters have a text box or a drop-down list. Once a

configuration change has been made on a page, click

SAVE SETTINGS

or

NEXT at the bottom of the page to enable the new setting.

Note: To ensure the screen refreshes after a command entry, be

sure that Internet Explorer is configured as follows: Click Tools,

Internet Options, General, Temporary Internet Files, and Settings.

The setting for Check for newer versions of stored pages should be

Every visit to the page.

S

ETUP

W

IZARD

9

Setup Wizard

1. Begin the Setup Wizard

If this is the first time the Setup Wizard has been launched, select

your country and click Apply. Verify you have selected the correct

country and click OK.

Click NEXT.

2. Create a password for the router

Follow the on-screen instructions to create a password for access to

the router. Remember that there is no current password to enter.

After creating and confirming a password, click NEXT.

C

ONFIGURING

THE

W

IRELESS

54M

BPS

ADSL R

OUTER

10

3. Enter your wireless network and security information

You will see the Channel and SSID page. Enter the appropriate

information for your wireless and security settings. Refer to the table

that follows for descriptions of the different settings. Click NEXT

when done.

Parameter Description

SSID Service Set ID. The SSID must be the same on the Wireless

54Mbps ADSL Router and all of its wireless clients.

SSID Broadcast Enable or disable the broadcasting of the SSID.

S

ETUP

W

IZARD

11

Click NEXT to continue.

4. Enter your Parameter Settings

Select the country of your Internet Service Provider (ISP) and the

name or type of your ISP. This will automatically configure the

Wireless 54Mbps ADSL Router with the correct Protocol,

Encapsulation and VPI/VCI settings for your ISP.

If your Country or Internet Service Provider is not listed, you will need

to manually enter the settings. Go to “Parameter Setting - Country or

ISP Not Listed” in this manual for more information. (It appears later

in this document.)

If your ISP uses PPPoA or PPPoE, then you will need to enter the

username, password and DNS Server address supplied by your ISP.

If your ISP uses 1483 Routing, then you will need to enter the IP

Wireless Mode This device supports both 11g and 11b wireless networks. Make

your selection depending on the type of wireless network that you

have.

Security Type For Security, you can select either No WEP, No WPA; WEP Only; or

WPA Only. If you select WEP or WPA, you will need to enter either

a Pass phrase or a Key on the next page.

Channel The radio channel used by the wireless router and its clients to

communicate with each other. This channel must be the same on

the Wireless 54Mbps ADSL Router and all of its wireless clients.

The Wireless 54Mbps ADSL Router will automatically assign itself

a radio channel, or you may select one manually.

Parameter Description

C

ONFIGURING

THE

W

IRELESS

54M

BPS

ADSL R

OUTER

12

address, Subnet Mask, Default Gateway and DNS Server address

supplied by your ISP.

Note: By default 192.168.2.1 is set for the DNS Server address,

this needs to be changed to reflect your ISP’s DNS Server

address.

Click NEXT to continue to the Confirm settings page.

Parameter Setting - Country or ISP Not Listed

If your Country or Internet Service Provider is not listed in the

dropdown menu, select Other. This will allow you to manually

configure your ISP settings.

For manual configuration you will need to know the Protocol, DNS

Server, Encapsulation, and VPI/VCI settings used by your ISP. If you

have a Static IP address you will also need to know the IP address,

Subnet Mask, and Gateway address. Please contact your ISP for

these details if you do not already have them.

After selecting Other you will be required to select the Protocol your

ISP uses from the Internet Service Provider dropdown list.

S

ETUP

W

IZARD

13

ISP uses Bridging - Parameter Setting

Enter the Bridging settings provided by your ISP.

Click NEXT to continue to the Confirm settings page.

Parameter Description

Management IP Address Enter the IP address provided by your ISP. (Default:

192.168.2.1)

VPI/VCI Enter the Virtual Path Identifier (VPI) and Virtual

Circuit Identifier (VCI) supplied by your ISP.

Encapsulation Select the encapsulation used by ISP from the

dropdown list.

C

ONFIGURING

THE

W

IRELESS

54M

BPS

ADSL R

OUTER

14

ISP uses 1483 Bridging-DHCP - Parameter Setting

Enter the Bridging settings provided by your ISP.

Click NEXT to continue to the Confirm settings page (see “5. Confirm

your settings” later in this document).

Parameter Description

DNS Server Enter the Domain Name Server address.

VPI/VCI Enter the Virtual Path Identifier (VPI) and Virtual

Circuit Identifier (VCI) supplied by your ISP.

Encapsulation Select the encapsulation used by ISP from the

dropdown list.

S

ETUP

W

IZARD

15

ISP uses 1483 Bridging-Fixed IP - Parameter Setting

Enter the bridging settings provided by your ISP.

Click NEXT to continue to the Confirm settings page (see “5. Confirm

your settings” later in this document).

Parameter Description

IP Address Enter the IP address provided by your ISP.

Subnet Mask Enter the subnet mask address provided by your ISP.

Default Gateway Enter the gateway address provided by your ISP.

DNS Server Enter the Domain Name Server address.

VPI/VCI Enter the Virtual Path Identifier (VPI) and Virtual

Circuit Identifier (VCI) supplied by your ISP.

Encapsulation Select the encapsulation used by ISP from the

dropdown list.

C

ONFIGURING

THE

W

IRELESS

54M

BPS

ADSL R

OUTER

16

ISP uses PPPoE - Parameter Setting

Enter the PPPoE (Point-to-Point Protocol over Ethernet) settings

provided by your ISP.

Click NEXT to continue to the Confirm settings page (see “5. Confirm

your settings” later in this document).

Parameter Description

VPI/VCI Enter the Virtual Path Identifier (VPI) and Virtual

Circuit Identifier (VCI) supplied by your ISP.

Encapsulation Select the encapsulation used by ISP from the

dropdown list.

Username Enter the ISP assigned user name.

Password Enter your password.

Confirm Password Confirm your password.

S

ETUP

W

IZARD

17

ISP uses PPPoA - Parameter Setting

Enter the PPPoA (Point-to-Point Protocol over ATM) settings provided

by your ISP.

Click NEXT to continue to the Confirm settings page (see “5. Confirm

your settings” later in this document).

Parameter Description

VPI/VCI Enter the Virtual Path Identifier (VPI) and Virtual

Circuit Identifier (VCI) supplied by your ISP.

Encapsulation Select the encapsulation used by ISP from the

dropdown list.

Username Enter the ISP assigned user name.

Password Enter your password.

Confirm Password Confirm your password.

C

ONFIGURING

THE

W

IRELESS

54M

BPS

ADSL R

OUTER

18

ISP uses 1483 Routing - Parameter Setting

Enter the RFC1483 Routing settings provided by your ISP.

Click NEXT to continue to the Confirm settings page (see “5. Confirm

your settings”).

Parameter Description

IP Address Enter the IP address provided by your ISP.

Subnet Mask Enter the subnet mask address provided by your ISP.

Default Gateway Enter the gateway address provided by your ISP.

DNS Server Enter the Domain Name Server address.

VPI/VCI Enter the Virtual Path Identifier (VPI) and Virtual

Circuit Identifier (VCI) supplied by your ISP.

Encapsulation Select the encapsulation used by ISP from the

dropdown list.

Page is loading ...

US Robotics Wireless 54Mbps ADSL Router User manual

This manual is also suitable for

US Robotics Wireless 54Mbps ADSL Router User manual

Related papers

Other documents