Toro Debris Kit, STX-38 EFI Stump Grinder Installation guide

Brand: Toro

Model: Debris Kit, STX-38 EFI Stump Grinder

Type: Installation guide

Toro Debris Kit, STX-38 EFI Stump Grinder enhances the performance and protection of your stump grinder. This kit includes a muffler guard, hydraulic cover, cylinder cover, hose cover, guard mount, and clamp plates. These components work together to minimize debris accumulation, protect vital components from damage, and improve overall grinding efficiency. With this kit, you'll experience reduced downtime for cleaning and maintenance, allowing you to focus on completing your grinding tasks quickly and effectively.

FormNo.3436-227RevA

DebrisKit

STX-38EFIStumpGrinderwithIntelli-Sweep

ModelNo.140-3624

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Muferguard

Bolt(5/16x2-1/2inches)

Locknut(5/16inch)

Replacethemuferguard.

Hydrauliccover1

Topbracket1

Bottombracket1

Leftbracket

Hookandloopfastener

Drillthehydrauliccoverandbracket

holes.

Cylindercover

Hosecover1

Bolt(1/4x1inch)

Nut(1/4inch)

Installthecovers.

Guardmount

Clampplate

Bolt(5/16x1-1/4inches)

Locknut(5/16inch)

Replacetheguardmount.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3436-227*A

PreparingtheMachine

NoPartsRequired

Procedure

1.Parkthemachineonalevelsurface.

2.Engagetheparkingbrake.

3.Lowerthegrinder.

4.Shutofftheengineandremovethekey.

5.Allowtheenginetocoolcompletely.

WARNING

Contactwithhotsurfacesmaycause

personalinjury.

Keepyourhands,feet,face,clothingand

otherbodypartsawaythemuferand

otherhotsurfaces.

ReplacingtheMufer

Guard

Partsneededforthisprocedure:

Muferguard

Bolt(5/16x2-1/2inches)

Locknut(5/16inch)

Procedure

1.Removetheexistingmuferguard(Figure1).

Important:Ensurethatyoudonotdamage

thefuellineasyouremovetheguard.

g309583

Figure1

1.Bolt(4)3.Washer(4)

2.Muferguard4.Nut(4)

2.Installthenewmuferguardusing2bolts(5/16

x2-1/2inches)and2nuts(5/16inch)intherear

holes(Figure2).

g309582

Figure2

1.Muferguard3.Nut—5/16inch(2)

2.Bolt—5/16x2-1/2inches

(2)

DrillingtheHydraulicCover

andBracketHoles

Partsneededforthisprocedure:

1Hydrauliccover

1Topbracket

1Bottombracket

Leftbracket

Hookandloopfastener

Procedure

1.Removetheexistinghydrauliccover(Figure3).

Retainthebolts.

g309727

Figure3

1.Bolt—5/16x1-1/4inch(2)

2.Existinghydrauliccover

2.Looselyinstallthenewhydrauliccoverusinga

boltthatyouretainedontheleftside(Figure4).

g309726

Figure4

1.Hydrauliccover

2.Bolt—5/16x1-1/4inch

3.Measureandcut5hookandloopfastenerstrips

ofapproximatelythefollowinglengths:

•14cm(5-1/2inches)

•15.5cm(6-1/8inches)

•20.7cm(8-1/8inches)

•25.1cm(10inches)

•33cm(13inches)

4.Cleanthesurfacesontheframeandhydraulic

covernearthehydrauliccylinderandthe

hydraulichoses.

5.Removethebackingfromthefastenerstrips

andadherethestripstotheframeandhydraulic

cover(Figure5andFigure6).

Note:Youwillusethebracketsinthekitto

securethecylinderandhosecoverstothe

fastener.Markthebracketlocationstohelpwith

thefastenerstripplacement(seeFigure7and

Figure8).

g309838

Figure5

1.14cm(5-1/2inch)fastener

strip

3.20.7cm(8-1/8inch)

fastenerstrip

2.25.1cm(10inch)fastener

strip

g309837

Figure6

1.15.5cm(6-1/8inch)

fastenerstrip

2.33cm(13inch)fastener

strip

6.Removethehydrauliccover.

7.Usingeachbracketasatemplate,drillholes

(1/4inchdiameter)intotheframe(Figure7and

Figure8).

g309860

Figure7

1.Leftbracket2.Drillahole(1/4inch

diameter)here.

g309861

Figure8

1.Drillahole(1/4inch

diameter)here.

3.Lowerbracket

2.Upperbracket

InstallingtheCovers

Partsneededforthisprocedure:

Cylindercover

1Hosecover

Bolt(1/4x1inch)

Nut(1/4inch)

Procedure

Figure9showsthe2coversforthisprocedure.

g309894

Figure9

1.Cylindercover

2.Hosecover

1.Installthehosecoveraroundthehoses,withthe

taperedendup(Figure10).

g309896

Figure10

1.Hosecover

2.Bolt(1/4x1inch)andnut

(1/4inch)

2.Aligntheholesonthebottomofthecoverwith

theholesintheframe.Adhereittothehookand

loopfastenerstrip.

3.Securethecoverusingtheleftbracket,2bolts

(1/4x1inch),and2nuts(1/4inch)asshown

inFigure10.

4.Securethecovertothehosesusingthecable

tie.

5.Installthecylindercoveroverthehydraulic

cylinder,withthetaperedendtowardtherod

(Figure11).

g309895

Figure11

1.Existingbolt(3/8inchx

1-1/4inch)

3.Cylindercover

2.Bolt(1/4x1inch)andnut

(1/4inch)

6.Aligntheholesinthecoverwiththeholesinthe

frame.Adherethecovertothehookandloop

fastenerstrips.

7.Securethebottomofthecoverusingthebottom

bracket,2bolts(3/8inchx1-1/4inch),and2

nuts(1/4inch)asshowninFigure11.

8.Placethehydrauliccoverontheframe,and

securethetopofthecylindercoverusingthe

topbracket,2bolts(5/16x1-1/4inch,previously

removed,and1/4inchx1-1/4inch)and1nut

(1/4inch)asshowninFigure11.

Note:Positionthetabonthehydrauliccover

overthetopbracket.

9.Securethehydrauliccoverusing1bolt(5/16x

1-1/4inch,previouslyremoved).

10.Adherethehosecovertothehookandloop

fastenerstriponthehydrauliccover.

ReplacingtheGuardMount

Partsneededforthisprocedure:

Guardmount

Clampplate

Bolt(5/16x1-1/4inches)

Locknut(5/16inch)

Procedure

1.Removetheshieldassemblyfromthegrinder

head(Figure12).Retainthefasteners.

g309639

Figure12

1.Bolt—5/16x1-1/4inches

(8)

3.Shieldassembly

2.Locknut—5/16inch(8)

2.Removebothshieldsandclampplatesfromthe

guardmount(Figure13).Retainthefasteners

andshields.

g309640

Figure13

1.Bolt—5/16x1-1/4inches

(12)

4.Locknut—5/16inch(12)

2.Clampplate(2)5.Guardmount

3.Shield(2)

3.Installthenewguardmountusing8boltsand8

nutsthatyouremovedinstep1(Figure14).

g309638

Figure14

1.Bolt—5/16x1-1/4inches

(8)

3.Locknut—5/16inch(8)

2.Guardmount

4.Installbothshieldstotheguardmountusing

aclampplateandthe6boltsand6nutsyou

removedfromeachshieldinstep2(Figure15).

Note:Donotusetherearholeintheclamp

platesinthisstep.

g309637

Figure15

1.Bolt—5/16x1-1/4inches

(12)

4.Guardmount

2.Clampplate(2)5.Locknut—5/16inch(12)

3.Shield(2)

5.Usingtheclampplateandguardmountasa

template,drillahole(5/16inchdiameter)into

bothshields(Figure16).

g309636

Figure16

1.Drillahole(5/16inchdiameter)here.

6.Installaboltandnutinbothholes.

Toro Debris Kit, STX-38 EFI Stump Grinder Installation guide

Toro Debris Kit, STX-38 EFI Stump Grinder Installation guide

Toro Debris Kit, STX-38 EFI Stump Grinder Installation guide

Related papers

Other documents