2. Toro
  3. Stump Grinder Fit-Up Kit, TX 1000 Compact Tool Carrier

Toro Stump Grinder Fit-Up Kit, TX 1000 Compact Tool Carrier Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Toro Stump Grinder Fit-Up Kit, TX 1000 Compact Tool Carrier Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
FormNo.3413-793RevB
StumpGrinderFit-UpKit
TX1000CompactToolCarrier
ModelNo.23172
InstallationInstructions
WARNING
CALIFORNIA
Proposition65Warning
ThisproductcontainsachemicalorchemicalsknowntotheStateofCalifornia
tocausecancer,birthdefects,orreproductiveharm.
Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.
Installation
LooseParts
Usethechartbelowtoverifythatallpartshavebeenshipped.
ProcedureDescription
Qty.
Use
1
Nopartsrequired
–
Preparethemachine.
Rightshieldbracket1
Leftshieldbracket
1
Bolt(1/4x3/4inch)
4
2
Locknut(1/4inch)
4
Installtheshieldbrackets.
Shieldsupport
2
Shield
1
Bolt(1/4x1-1/2inch)
8
Washer8
3
Locknut(1/4inch)
8
Assembletheoperatorshield.
4
Quick-attachassembly
1Replacethequick-attachassembly.
©2017—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.Toro.com.
OriginalInstructions(EN)
PrintedintheUSA
AllRightsReserved
*3413-793*B
1
PreparingtheMachine
NoPartsRequired
Procedure
1.Parkthemachineonalevelsurface.
2.Engagetheparkingbrake.
3.Lowertheloaderarms.
4.Shutofftheengineandremovethekey.
g036689
Figure1
2
InstallingtheShield
Brackets
Partsneededforthisprocedure:
1Rightshieldbracket
1
Leftshieldbracket
4
Bolt(1/4x3/4inch)
4
Locknut(1/4inch)
Procedure
1.Measureinfromtheedgesoftheframeas
illustratedinFigure2andmarkthelocations
oftheholesformountingtheshieldbracketon
bothsidesofthemachine.
Note:Iftheholesexist,skiptostep3.
g213269
Figure2
1.7.0cm(2-3/4inches)
4.Holes
2.5.7cm(2-1/4inches)5.Referencebar
3.1.3cm(1/2inch)
2
2.Drillahole(9/32inch)throughtheframeateach
markedlocation.
3.Installtheleftshieldbracketontheleftframe
using2bolts(1/4x3/4inch)and2locknuts(1/4
inch)asshowninFigure3.
g202825
Figure3
1.Bolts(1/4x3/4inch)3.Locknut(1/4inch)
2.Leftshieldbracket
4.Installtherightshieldbracketontherightframe
using2bolts(1/4x3/4inch)and2locknuts(1/4
inch),similartoFigure3.
3
AssemblingtheOperator
Shield
Partsneededforthisprocedure:
2
Shieldsupport
1
Shield
8
Bolt(1/4x1-1/2inch)
8Washer
8
Locknut(1/4inch)
Procedure
1.Assembletheshieldandexibleskirttothe
shieldsupports,asillustratedinFigure4,using
8bolts(1/4x1-1/2inch),8washers,and8
locknuts(1/4inch).
g202842
Figure4
1.Locknut(8)5.Skirt
2.Washer(8)6.Shieldsupport(2)
3.Shield7.Shieldbracket(2)
4.Bolt(8)
2.Slidetheshieldsupportsintothepocketsinthe
shieldbracketsonthetractionunit(Figure4).
Note:Theskirtshoulddrapeovertheengine
orhood.
3
4
ReplacingtheQuick-Attach
Assembly
Partsneededforthisprocedure:
1
Quick-attachassembly
Procedure
1.Laythestumpgrinderatontheoor.
2.Placewoodblocksunderthebodyofthestump
grindersothatthequick-attachplateisoffthe
oor.
3.Removethelargebolt(1x2-1/4inch),washer,
nut(1inch),2smallbolts(1/2x1-1/2inches),
and2nuts(1/2inch)securingthequick-attach
assemblytothestumpgrinder(Figure5).
Removetheassembly.
g206389
Figure5
1.Largebolt(1x2-1/4inch),
washer,andnut(1inch)
3.Quick-attachassembly
2.Smallbolt(1/2x1-1/2
inches)andnut(1/2inch)
4.Installthenewquick-attachassemblytothe
stumpgrinderusingthehardwareyouremoved,
asshowninFigure5.
Note:Thenewquick-attachassemblyhasa
widerhoseloop.
5.Torquethelargebolt(1x2-1/4inch)to406N∙m
(300ft-lb),andtorquethesmallbolts(1/2x
1-1/2inches)to101N∙m(75ft-lb).
6.Routethehosesthroughthehoseloop(Figure
6).
g208071
Figure6
1.Hoseloop2.Hoses
4
/