Flowtoys 6142412774 Lumina Twirl Baton is the world's first durable, rechargeable illuminated twirling baton. Made with aerospace-grade carbon fiber and polycarbonate, it's thin, lightweight, yet super strong and rigid for optimal comfort and performance. The transparent end tubes allow for maximum glow and protection. It features a MicroUSB rechargeable capsule light unit with super bright multicolor LEDs and a built-in high power Li-ion battery. With its anti-vibration diffusive insert, it ensures quiet catches.
Flowtoys 6142412774 Lumina Twirl Baton is the world's first durable, rechargeable illuminated twirling baton. Made with aerospace-grade carbon fiber and polycarbonate, it's thin, lightweight, yet super strong and rigid for optimal comfort and performance. The transparent end tubes allow for maximum glow and protection. It features a MicroUSB rechargeable capsule light unit with super bright multicolor LEDs and a built-in high power Li-ion battery. With its anti-vibration diffusive insert, it ensures quiet catches.
Lumina Twirl™ Baton
features
operating instructions
troubleshooting
Presenting the world’s rst durable, rechargeable illuminated twirling baton, combining
high-performance materials typically used in the aerospace and racing industries. Thin and
lightweight, yet super-strong and rigid carbon ber shaft for optimum comfort and perfor-
mance. Transparent yet sti and impact-resistant polycarbonate end-tubes. Soft and clear,
yet incredibly durable silicone end caps for maximum glow and protection.
Made with the same high-tech materials that took humanity to space, your illuminated
owtoys twirling baton will help take your baton practice to new heights.
CAPSULE LIGHT
MicroUSB rechargeable light unit with
super bright multicolor LEDs. Built in high
power Li-ion battery. See accompanying
capsule light insert for instructions.
TUBES
Transparent yet virtually bulletproof polycarbonate.
Connects to owcaps via snap-button holes.
CARBON FIBER SHAFT
Custom woven 12mm carbon ber with
custom elastomer grip. Thin and lightweight,
yet super-strong and rigid.
COMPOSITE CONNECTOR
3d-printed connectors screw into
carbon ber shaft to create a rm and
secure connection.
FLOWCAP
Thick, soft, durable silicone end cap
with rigid inner structure that snaps securely
onto our tubes and releases with a rm twist.
Recessed end-button operates the light.
ANTI-VIBRATION
Diusive insert dampens vibration
for quiet catches.
FOREVER FLOW LIFETIME WARRANTY
Flowtoys are designed to last you a lifetime, but nothing is indestructible,
so we provide this warranty to enable you to freely nd your ow*.
If you manage to break a owtoys product, we oer free replacements on
defective or non-working parts due to intended use, and
50% credit for products in any condition at any time. Battery depletion is normal
wear & tear and covered for free in rst 2 years and half-price/capsule after.
If you need warranty support, please contact us at support@owtoys.com.
* Please check owtoys.com for full warranty details.
Flowtoys reserves the right to refuse coverage to anyone abusing this warranty.
Please contact us before sending in your product, or it may be returned to sender.
Lumina Twirl™ Baton
features
operating instructions
troubleshooting
Presenting the world’s rst durable, rechargeable illuminated twirling baton, combining
high-performance materials typically used in the aerospace and racing industries. Thin and
lightweight, yet super-strong and rigid carbon ber shaft for optimum comfort and perfor-
mance. Transparent yet sti and impact-resistant polycarbonate end-tubes. Soft and clear,
yet incredibly durable silicone end caps for maximum glow and protection.
Made with the same high-tech materials that took humanity to space, your illuminated
owtoys twirling baton will help take your baton practice to new heights.
CAPSULE LIGHT
MicroUSB rechargeable light unit with
super bright multicolor LEDs. Built in high
power Li-ion battery. See accompanying
capsule light insert for instructions.
TUBES
Transparent yet virtually bulletproof polycarbonate.
Connects to owcaps via snap-button holes.
CARBON FIBER SHAFT
Custom woven 12mm carbon ber with
custom elastomer grip. Thin and lightweight,
yet super-strong and rigid.
COMPOSITE CONNECTOR
3d-printed connectors screw into
carbon ber shaft to create a rm and
secure connection.
FLOWCAP
Thick, soft, durable silicone end cap
with rigid inner structure that snaps securely
onto our tubes and releases with a rm twist.
Recessed end-button operates the light.
ANTI-VIBRATION
Diusive insert dampens vibration
for quiet catches.
FOREVER FLOW LIFETIME WARRANTY
Flowtoys are designed to last you a lifetime, but nothing is indestructible,
so we provide this warranty to enable you to freely nd your ow*.
If you manage to break a owtoys product, we oer free replacements on
defective or non-working parts due to intended use, and
50% credit for products in any condition at any time. Battery depletion is normal
wear & tear and covered for free in rst 2 years and half-price/capsule after.
If you need warranty support, please contact us at support@owtoys.com.
* Please check owtoys.com for full warranty details.
Flowtoys reserves the right to refuse coverage to anyone abusing this warranty.
Please contact us before sending in your product, or it may be returned to sender.
TROUBLESHOOTING
My owcap won’t release from the tube.
Make sure to grip the top end of your owcap when removing it. If you grip lower down the cap,
the silicone can press against the tube, making it harder to remove.
My capsule lights are falling out of the owcap.
When installing capsule lights into a owcap, make sure to TWIST until you feel the light settle
into place. You should be able to wiggle it left and right a tiny bit.
CARING FOR YOUR BATON
Do not use glowsticks or WD-40 with tubing.
While polycarbonate is very strong, it breaks down in the presence of certain esters, including
those produced by chemical glowsticks, mineral spirits and WD-40. Do NOT put chemical glow-
sticks into the tubes, otherwise they can become brittle and shatter.
Make sure all caps and connectors are fully secured before use!
Check that the buttons in your caps and connectors are fully clicked into tubing holes.
Clean your grip!
Grip can wear out with use and is aected by oils from our skin. To prolong the life of your grip,
clean it after heavy use and before long periods of storage. Use rubbing alcohol and a cloth, OR
a cloth with warm soapy water to remove oils from the grip. Wipe away any soap residue with
clean water.
If your owcaps get dirty, you can clean them with soap and warm water, or put them in the
wash with your laundry: air-dry, no heat!
Flowtoys makes more LED batons and we make more than batons!
Visit us online to see our full line of lights, props and
gear for dance, twirling, juggling and lifestyle.
owtoys.com 2021.09
ATTACHING/REMOVING FLOWCAPS FROM TUBES:
To detach, twist cap rmly to release the internal snap-buttons and pull o the tube.
To install, place cap over tube, push and twist until the buttons click into the holes.
ATTACHING CAPSULES TO FLOWCAPS:
Insert capsule light into owcap, button side in. Twist and
push until light clicks/settles into place. The seams of the
capsule must be aligned with the buttons inside the cap
for it to t in the tube.
*click!*
Note: The owcap connects very rmly to the end of the tube.
To twist and remove, you must grip the tube that the cap is
connected to, not the carbon ber shaft.
Always check your connections before use.
Tip: If you nd it dicult to
remove the owcap from the
tube, check your hand grip.
You may be gripping the inter-
nal buttons against the tube!
We provide a grippy mat - you
can use it to help by holding
the tube with the grip mat,
while twisting the cap o.
USING YOUR FLOWCAPS
TROUBLESHOOTING
My owcap won’t release from the tube.
Make sure to grip the top end of your owcap when removing it. If you grip lower down the cap,
the silicone can press against the tube, making it harder to remove.
My capsule lights are falling out of the owcap.
When installing capsule lights into a owcap, make sure to TWIST until you feel the light settle
into place. You should be able to wiggle it left and right a tiny bit.
CARING FOR YOUR BATON
Do not use glowsticks or WD-40 with tubing.
While polycarbonate is very strong, it breaks down in the presence of certain esters, including
those produced by chemical glowsticks, mineral spirits and WD-40. Do NOT put chemical glow-
sticks into the tubes, otherwise they can become brittle and shatter.
Make sure all caps and connectors are fully secured before use!
Check that the buttons in your caps and connectors are fully clicked into tubing holes.
Clean your grip!
Grip can wear out with use and is aected by oils from our skin. To prolong the life of your grip,
clean it after heavy use and before long periods of storage. Use rubbing alcohol and a cloth, OR
a cloth with warm soapy water to remove oils from the grip. Wipe away any soap residue with
clean water.
If your owcaps get dirty, you can clean them with soap and warm water, or put them in the
wash with your laundry: air-dry, no heat!
Flowtoys makes more LED batons and we make more than batons!
Visit us online to see our full line of lights, props and
gear for dance, twirling, juggling and lifestyle.
owtoys.com 2021.09
ATTACHING/REMOVING FLOWCAPS FROM TUBES:
To detach, twist cap rmly to release the internal snap-buttons and pull o the tube.
To install, place cap over tube, push and twist until the buttons click into the holes.
ATTACHING CAPSULES TO FLOWCAPS:
Insert capsule light into owcap, button side in. Twist and
push until light clicks/settles into place. The seams of the
capsule must be aligned with the buttons inside the cap
for it to t in the tube.
*click!*
Note: The owcap connects very rmly to the end of the tube.
To twist and remove, you must grip the tube that the cap is
connected to, not the carbon ber shaft.
Always check your connections before use.
Tip: If you nd it dicult to
remove the owcap from the
tube, check your hand grip.
You may be gripping the inter-
nal buttons against the tube!
We provide a grippy mat - you
can use it to help by holding
the tube with the grip mat,
while twisting the cap o.
USING YOUR FLOWCAPS
-
1
-
2
Flowtoys 6142412774 Lumina Twirl Baton is the world's first durable, rechargeable illuminated twirling baton. Made with aerospace-grade carbon fiber and polycarbonate, it's thin, lightweight, yet super strong and rigid for optimal comfort and performance. The transparent end tubes allow for maximum glow and protection. It features a MicroUSB rechargeable capsule light unit with super bright multicolor LEDs and a built-in high power Li-ion battery. With its anti-vibration diffusive insert, it ensures quiet catches.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Flowtoys GLO-510 User manual
-
Flowtoys Composite LED Isolation Baton User manual
-
Flowtoys 43220-222986 User manual
-
Flowtoys MAN031 User manual
-
Flowtoys MAN033 User manual
-
Flowtoys HIGH PERFORMANCE User guide
-
Flowtoys podpoi v2 Capsule 2.0 Glow Poi Operating instructions
-
Flowtoys Vision Clubs Operating instructions
-
Flowtoys Crystal Poi User guide
-
Flowtoys Trikon User manual
Other documents
-
ESP ExB Series Technical And Operating Manual
-
Verathon GlideScope System AVL Single-Use Operation & Maintenance Manual
-
Sentinel 880 Sigma 130Ci User manual
-
Nagra PL-P User manual
-
Metra 3MHST12 Datasheet
-
3M LifeASSURE™ PDA Series Filter Cartridge Operating instructions
-
Bodum 11195-16 User manual
-
Sealife SportDiver User manual
-
-
ibis Mojo 3 Instruction book
