H3C S5500-28C-EI Quick start guide

H3C S5500-EI Series Ethernet Switches

Quick Start

Hangzhou H3C Technologies Co., Ltd.

http://www.h3c.com

Manual Version: T2-08225N-20071215-C-1.01

and its licensors

No part of this manual may be reproduced or transmitted in any form

or by any means without prior written consent of Hangzhou H3C

Technologies Co., Ltd.

Trademarks

H3C, , Aolynk, , H

3

Care,

, TOP G, , IRF,

NetPilot, Neocean, NeoVTL, SecPro, SecPoint, SecEngine, SecPath,

Comware, Secware, Storware, NQA, VVG, V

2

G, V

n

G, PSPT, XGbus,

N-Bus, TiGem, InnoVision and HUASAN are trademarks of Hangzhou

H3C Technologies Co., Ltd.

All other trademarks that may be mentioned in this manual are the

property of their respective owners.

Notice

The information in this document is subject to change without notice.

Every effort has been made in the preparation of this document to

ensure accuracy of the contents, but all statements, information, and

recommendations in this document do not constitute the warranty of

any kind, express or implied.

To obtain the latest information, please access:

http://www.h3c.com

Technical Support

customer_service@h3c.com

http://www.h3c.com

About This Manual

Related Documentation

In addition to this manual, each H3C S5500-EI Series Ethernet

Switches documentation set includes the following:

Manual Content

H3C S5500-EI Series Ethernet

Switches Operation Manual

It is used for assisting the users

in data configurations and

typical applications

H3C S5500-EI Series Ethernet

Switches Command Manua

It is used for assisting the users

in using various commands.

H3C S5500-EI Series Ethernet

Switches Installation Manual

It is used for assisting the users

in switch installation, booting up,

hardware and software

maintenance.

Organization

H3C S5500-EI Series Ethernet Switches Quick Start is

organized as follows:

Chapter Contents

1 Product Overview

Introduces the characteristics

and technical specifications of

S5500-EI Series Ethernet

Switches.

Chapter Contents

2 Installation Preparations

Introduces the installation

preparation and precaution of

S5500-EI Series Ethernet

Switches.

3 Installation

Introduces the procedures to

install an S5500-EI Series

Ethernet Switch, including the

setup of the mainframe, cards

and cables.

4 Lightning Protection of the

Switch

Introduces lightning protection

of S5500-EI Series Ethernet

Switches.

Conventions

The manual uses the following conventions:

I.

GUI conventions

Convention Description

< >

Button names are inside angle brackets.

For example, click <OK>.

[ ]

Window names, menu items, data table

and field names are inside square

brackets. For example, pop up the [New

User] window.

/

Multi-level menus are separated by forward

slashes. For example, [File/Create/Folder].

II. Symbols

Convention Description

Warning

Means reader be extremely careful.

Improper operation may cause bodily

injury.

Caution

Means reader be careful. Improper

operation may cause data loss or damage

to equipment.

 Note Means a complementary description.

Environmental Protection

This product has been designed to comply with the requirements

on environmental protection. For the proper storage, use and disposal

of this product, national laws and regulations must be observed.

Quick Start

H3C S5500-EI Series Ethernet Switches

Table of Contents

i

Table of Contents

Chapter 1 Product Overview ........................................................1-1

1.1 Introduction ........................................................................1-1

1.2 S5500-28C-EI LEDs ..........................................................1-3

1.3 S5500-28C-EI-DC LEDs ....................................................1-9

1.4 S5500-52C-EI LEDs ........................................................1-15

1.5 S5500-28C-PWR-EI LEDs...............................................1-15

1.6 S5500-52C-PWR-EI LEDs...............................................1-22

1.7 S5500-28F-EI LEDs.........................................................1-22

1.8 System Specifications of the S5500-EI Series ................1-28

1.9 Pluggable Modules...........................................................1-32

1.10 Optional Interface Modules ............................................1-34

1.10.1 Description of LEDs on Extended Modules.........1-34

1.11 CX4 Cable......................................................................1-35

Chapter 2 Installation Preparations.............................................2-1

2.1 Safety Precautions .............................................................2-1

2.2 Installation Site...................................................................2-1

2.2.1 Temperature/Humidity.............................................2-2

2.2.2 Cleanness................................................................2-2

2.2.3 Electromagnetic Susceptibility.................................2-3

2.2.4 Laser Safety ............................................................2-4

2.3 Installation Tools ................................................................2-5

Chapter 3 Installation....................................................................3-1

3.1 Installing the Switch into a 19-Inch Cabinet.......................3-1

3.1.1 Introduction to Mounting Ears .................................3-2

Quick Start

H3C S5500-EI Series Ethernet Switches

Table of Contents

ii

3.1.2 Introduction to Guide Rails ......................................3-4

3.1.3 Using Front Mounting Ears to Install the Switch .....3-5

3.1.4 Using Front Mounting Ears and a Tray ...................3-7

3.1.5 Using Front and Rear Mounting Ears......................3-8

3.1.6 Using Front Mounting Ears and Guide Rails.........3-12

3.2 Mounting the Switch on a Workbench .............................3-15

3.3 Connecting the Power Cables and the Grounding Cable..........3-16

3.3.1 Connecting the AC Power Cable...........................3-16

3.3.2 Connecting the DC Power Cable ..........................3-18

3.3.3 Connecting the Grounding Cable..........................3-25

3.4 Connecting the Console Cable ........................................3-28

3.4.1 Console Cable .......................................................3-28

3.4.2 Connection Procedure...........................................3-29

3.5 Installing and Removing Optional Interface Modules ......3-30

3.5.1 10 GE XFP Interface Module ................................3-31

3.5.2 Short-haul Dual-port 10 GE CX4 Interface

Module...........................................................................

3-35

3.6 Installing and Removing the Dedicated CX4 Cable.........3-36

3.6.1 Installing the Dedicated CX4 Cable.......................3-36

3.6.2 Removing the Dedicated CX4 Cable.....................3-36

3.7 Verifying the Installation...................................................3-37

Chapter 4 Lightning Protection of the Switch ............................4-1

4.1 Installation of Lightning Arrester for AC Power (Socket Strip

with Lightning Protection).........................................................

4-1

Quick Start

H3C S5500-EI Series Ethernet Switches

List of Figures

iii

List of Figures

Figure 1-1 CX4 cable ............................................................1-35

Figure 3-1 Appearance of a standard front mounting ear .......3-3

Figure 3-2 Appearance of a rear mounting ear .......................3-3

Figure 3-3 Appearance of a guide rail .....................................3-5

Figure 3-4 Fix front mounting ears (1).....................................3-6

Figure 3-5 Fix front mounting ears (2).....................................3-7

Figure 3-6 Fix front mounting ears and load-bearing screws ..........3-8

Figure 3-7 Fix rear mounting ears...........................................3-9

Figure 3-8 Fix front and rear mounting ears .........................3-10

Figure 3-9 Effect diagram of front and rear mounting ear

installation (1) .................................................................

3-11

Figure 3-10 Effect diagram of front and rear mounting ear

installation (2) .................................................................

3-12

Figure 3-11 Install front mounting ears .................................3-13

Figure 3-12 Install guide rails ................................................3-13

Figure 3-13 Install front mounting ears and guide rails.........3-14

Figure 3-14 Effect diagram of front mounting ear and guide rail

installation.......................................................................

3-15

Figure 3-15 Power socket (recommended)...........................3-16

Figure 3-16 Installing AC power cable retainer .....................3-17

Figure 3-17 Appearance of the 12V RPS socket ..................3-19

Quick Start

H3C S5500-EI Series Ethernet Switches

List of Figures

iv

Figure 3-18 12V RPS power cable........................................3-19

Figure 3-19 12V RPS power connector ................................3-20

Figure 3-20 12V RPS port.....................................................3-20

Figure 3-21 Connect the 12V RPS connector to the chassis........3-21

Figure 3-22 Appearance of the 48V RPS port ......................3-22

Figure 3-23 Connect the 48V RPS connector to the chassis........3-23

Figure 3-24 Appearance of the –48V RPS port ....................3-24

Figure 3-25 Connect the 48V RPS connector to the chassis........3-24

Figure 3-26 Ground the switch through a grounding strip .........3-26

Figure 3-27 Ground the switch by burying the grounding body

into the earth...................................................................

3-27

Figure 3-28 Ground through an AC PE wire .........................3-27

Figure 3-29 Ground through the PGND of a power cabinet .........3-28

Figure 3-30 Console cable ....................................................3-29

Figure 3-31 Appearance of a one-port 10 GE XFP interface

module............................................................................

3-31

Figure 3-32 Front panel of a one-port 10 GE XFP interface

module............................................................................

3-31

Figure 3-33 Appearance of a dual-port 10 GE XFP interface

module............................................................................

3-32

Figure 3-34 Front panel of a dual-port 10 GE XFP interface

module............................................................................

3-32

Figure 3-35 Install a 10 GE XFP interface module................3-33

Quick Start

H3C S5500-EI Series Ethernet Switches

List of Figures

v

Figure 3-36 Appearance of a short-haul dual-port 10 GE CX4

interface module .............................................................

3-35

Figure 3-37 Front panel of a short-haul dual-port 10 GE CX4

interface module .............................................................

3-35

Figure 4-1 Diagram of lightning arrester .................................4-2

Quick Start

H3C S5500-EI Series Ethernet Switches

List of Tables

vi

List of Tables

Table 1-1 Models of the S5500-EI series ................................1-2

Table 1-2 Mapping between two ports forming a Combo port.........1-2

Table 1-3 LEDs on the front panel of the S5500-28C-EI.........1-4

Table 1-4 LEDs on the front panel of the S5500-28C-EI-DC...........1-9

Table 1-5 Descriptions of the LEDs on the front panel of

S5500-28C-PWR-EI .......................................................

1-15

Table 1-6 Description of LEDs on the front panel of the

S5500-28F-EI .................................................................

1-22

Table 1-7 System specifications of the S5500-EI series.......1-28

Table 1-8 Pluggable modules that the S5500-EI series support

........................................................................................

1-33

Table 1-9 Description of the LED for each extended module slot

........................................................................................

1-35

Table 2-1 Dust concentration limit in the equipment room......2-3

Table 2-2 Harmful gas limits in the equipment room...............2-3

Table 3-1 Installation methods for a switch with a width of 440

mm (17.3 in) or 436 mm (17.2 in.)....................................

3-2

Table 3-2 Selection of mounting ear for the S5500-EI series...........3-4

Table 3-3 Console cable pinouts ...........................................3-29

Quick Start

H3C S5500-EI Series Ethernet Switches

Chapter 1 Product Overview

1-1

Chapter 1 Product Overview

1.1 Introduction

H3C S5500-EI Series Ethernet Switches (hereinafter referred to

as the S5500-EI series) are Gigabit Ethernet switching products

developed by Hangzhou H3C Technologies Co., Ltd. (hereinafter

referred to as H3C). The S5500-EI series support diversified service

features, IPv6 forwarding, and routing function, and provide 10GE

extended module slots. Through the H3C proprietary cluster

management, you can streamline network management. The

S5500-EI series are designed to operate at the convergence or

access layer of enterprise networks and metropolitan area networks

(MANs). The S5500-EI series support the IPv4/IPv6 dual stack and

can also be used for connecting server groups in data centers.

Table 1-1 lists the models of the S5500-EI series.

Quick Start

H3C S5500-EI Series Ethernet Switches

Chapter 1 Product Overview

1-2

Table 1-1 Models of the S5500-EI series

Model

Number of

auto-sensing

10/100/1000Base

-T Ethernet ports

Number of

1000Base-X

SFP ports

Number

of

console

ports

S5500-28C-EI 24 4

S5500-28C-EI-D

C

24 4

S5500-52C-EI 48 4

S5500-28C-PWR

-EI

24 4

S5500-52C-PWR

-EI

48 4

S5500-28F-EI 8 24

1

Together with an auto-sensing 10/100/1000BASE-T Ethernet port,

each 1000Base-X SFP port forms a Combo port. For each Combo

port, either the SFP port or the auto-sensing 10/100/1000BASE-T

Ethernet port can be used at a time. For the mapping between the two

ports forming a Combo port, refer to

Table 1-2.

Table 1-2 Mapping between two ports forming a Combo port

Model

1000Base-X

SFP port

number

Auto-sensing

10/100/1000Base-T Ethernet

port number

25 22 S5500-28C-EI

S5500-28C-EI-

26 24

Quick Start

H3C S5500-EI Series Ethernet Switches

Chapter 1 Product Overview

1-3

27 21

DC

S5500-28C-PW

R-EI

28 23

49 46

50 48

51 45

S5500-52C-EI

S5500-52C-PW

R-EI

52 47

25 17

26 18

27 19

28 20

29 21

30 22

31 23

S5500-28F-EI

32 24

For the convenience of monitoring the running of the S5500-EI

series, LEDs are also equipped on their front panel.

1.2 S5500-28C-EI LEDs

For descriptions about LEDs, see Table 1-3. You can switch the

Mode LED display mode between speed and duplex by pressing the

Mode button on the panel.

Quick Start

H3C S5500-EI Series Ethernet Switches

Chapter 1 Product Overview

1-4

Table 1-3 LEDs on the front panel of the S5500-28C-EI

LED Mark Status Description

Speed Solid green Rate of the port

Mode LED Mode

Duple

x

Solid

yellow

Duplex mode of

the port

Solid green

The switch is

started normally.

Flashing green (1

Hz)

The system is

running a

power-on self-test

(POST).

Solid red

The system fails

the POST or a

power failure

occurs.

Flashing yellow (1

Hz)

Some ports fail a

POST or a port

failure occurs.

Power LED PWR

OFF

The power is

disconnected.

Quick Start

H3C S5500-EI Series Ethernet Switches

Chapter 1 Product Overview

1-5

LED Mark Status Description

Solid green

The AC power

supply is normal

and the RPS is

connected and

works normally.

Solid yellow

The RPS input is

normal, but an AC

input failure

occurs or no AC

power is

connected.

Redundant

power system

LED

RPS

OFF

No RPS is

connected.

Solid green

The module is in

position and

works normally.

Flashing yellow

The switch does

not support the

module or a

module failure

occurs.

Module LED MOD

OFF

No module is

installed.

7-segment

digital LED

Unit

POST

runnin

g

The power

LED

flashes

green

The LED displays

the POST test ID.

Quick Start

H3C S5500-EI Series Ethernet Switches

Chapter 1 Product Overview

1-6

LED Mark Status Description

POST

failed

The power

LED

flashes

red

The LED flashes

the POST test ID

of the failed test.

Softwa

re

loading

The power

LED

flashes

green.

A bar rotates

clockwise around

the LED.

Fan

failure

The power

LED is

solid red.

The LED displays

F.

Over-t

emper

ature

alarm

The power

LED is

solid red.

The LED displays

t.

Cluster

state

The power

LED is

solid

green.

For a command

switch, the LED

displays C.

For a member

switch, the LED

displays S.

For a candidate

switch, the LED

displays c.

The LED displays

1 if there is only

one unit.

Quick Start

H3C S5500-EI Series Ethernet Switches

Chapter 1 Product Overview

1-7

LED Mark Status Description

Green

A 1000 Mbps link

is present. When

data is being

received or sent,

the LED flashes at

a high frequency.

Yellow

A 10/100 Mbps

link is present.

When data is

being received or

sent, the LED

flashes at a high

frequency.

Flashing

yellow (3

Hz)

The port fails the

POST.

Speed

OFF No link is present.

Green

The port works in

the full duplex

mode. The LED

flashes at a high

frequency when

data is being

received or sent.

10/100/1000B

ase-T port

status LED

—

Duplex

Yellow

The port works in

the half duplex

mode. The LED

flashes at a high

frequency when

data is being

received or sent

Quick Start

H3C S5500-EI Series Ethernet Switches

Chapter 1 Product Overview

1-8

LED Mark Status Description

Flashing

yellow (3

Hz)

The port fails the

POST.

OFF No link is present.

Green

A 1000 Mbps link

is present. When

data is being

received or sent,

the LED flashes at

a high frequency.

Flashing

yellow (3

Hz)

The port fails the

POST.

SFP port

status LED

(1000 Mbps)

—

The

Mode

button

has no

effect

on the

LED.

OFF No link is present.

Yellow

A 100 Mbps link is

present. When

data is being

received or sent,

the LED flashes at

a high frequency.

Flashing

yellow (3

Hz)

The port failed the

POST.

Speed

OFF No link is present.

SFP port

status LED

(100 Mbps)

—

Duplex

Green

The port operates

in the full duplex

mode. When data

is being received

or sent, the LED

flashes at a high

frequency.

Quick Start

H3C S5500-EI Series Ethernet Switches

Chapter 1 Product Overview

1-9

LED Mark Status Description

Flashing

yellow (3

Hz)

The port fails the

POST.

OFF No link is present.

1.3 S5500-28C-EI-DC LEDs

For descriptions about LEDs, see Table 1-4. You can switch the

Mode LED display mode between speed and duplex by pressing the

Mode button on the panel.

Table 1-4 LEDs on the front panel of the S5500-28C-EI-DC

LED Mark Status Description

Speed Solid green Rate of the port

Mode LED Mode

Duple

x

Solid

yellow

Duplex mode of

the port

Page is loading ...

H3C S5500-28C-EI Quick start guide

This manual is also suitable for

H3C S5500-28C-EI Quick start guide

Related papers

Other documents